Chain for modern Triple and 5 speed freewheel
#1
Senior Member
Thread Starter
Join Date: May 2010
Location: Austin,Texas
Posts: 801
Bikes: 73 Super Sport, 86 Tempo, 86 Peloton, 87 Super Sport, 83 Peugeot PFN10, 76 Super Course MK IV, 94 Univega Alpina 5.5
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quoted: 175 Post(s)
Liked 70 Times
in
34 Posts
Chain for modern Triple and 5 speed freewheel
What chain would work with a 5 speed Suntour freewheel and a 10 speed Campy Triple?
#2
Senior Member
Replace your 5 speed Suntour with a 6 speed Suntour 6 Ultra-spaced freewheel, then run any 8 speed chain, or an old school SEDIS 6 speed narrow. You still might get some chain rub inside the front rings in some configurations.
#5
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,793
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1390 Post(s)
Liked 1,322 Times
in
835 Posts
SRAM PC-58 or equivalent. I second the recommendation to replace the 5-speed with an ultra-6.
__________________
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
"Far and away the best prize that life offers is the chance to work hard at work worth doing." --Theodore Roosevelt
Capo: 1959 Modell Campagnolo, S/N 40324; 1960 Sieger (2), S/N 42624, 42597
Carlton: 1962 Franco Suisse, S/N K7911
Peugeot: 1970 UO-8, S/N 0010468
Bianchi: 1982 Campione d'Italia, S/N 1.M9914
Schwinn: 1988 Project KOM-10, S/N F804069
#6
Senior Member
Thread Starter
Join Date: May 2010
Location: Austin,Texas
Posts: 801
Bikes: 73 Super Sport, 86 Tempo, 86 Peloton, 87 Super Sport, 83 Peugeot PFN10, 76 Super Course MK IV, 94 Univega Alpina 5.5
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quoted: 175 Post(s)
Liked 70 Times
in
34 Posts
Why an ultra-6? Is it 120mm?
#7
Senior Member
A Suntour Ultra-6 freewheel takes up only slightly more (a few millimeters ish as I recall) horizontal space than almost all 5 speed freewheels of any brand. This is because the spacing cog-center to cog-center of an Ultra is narrower than regular 5 speed freewheels (identical to Shimano HG-7 cassettes as it happens). This means you can typically swap it onto your rear hub without making any other changes to the rear hub or hub spacing of the frame.
Furthermore you can use high-quality and light 7 or 8 speed chains with excellent performance in a friction-shifting set-up, which will also work adequately with the typical 7/8/9/10 double or triple crankset. The 7/8 speed chains will perform nicer on the narrower Ultra-6 spaced cogs than on the regular, wider-spaced 5 speed cogs.
Furthermore you can use high-quality and light 7 or 8 speed chains with excellent performance in a friction-shifting set-up, which will also work adequately with the typical 7/8/9/10 double or triple crankset. The 7/8 speed chains will perform nicer on the narrower Ultra-6 spaced cogs than on the regular, wider-spaced 5 speed cogs.
Last edited by Drakonchik; 06-02-10 at 01:52 PM.
#9
Senior Member
Thread Starter
Join Date: May 2010
Location: Austin,Texas
Posts: 801
Bikes: 73 Super Sport, 86 Tempo, 86 Peloton, 87 Super Sport, 83 Peugeot PFN10, 76 Super Course MK IV, 94 Univega Alpina 5.5
Mentioned: 2 Post(s)
Tagged: 1 Thread(s)
Quoted: 175 Post(s)
Liked 70 Times
in
34 Posts
I guess the consensus is that it will work to use a Suntour 5 speed freewheel with a modern triple and that 7/8 speed chain would work best. I f I were to coldset the rear drops I would probably go all the way from 120mm to 130mm to use 8/9/10 speed freehubs.
Thread
Thread Starter
Forum
Replies
Last Post
waltloc
Classic & Vintage
37
08-18-15 07:24 PM