I need some advice on rear wheel issue...
#1
Member
Thread Starter
Join Date: May 2011
Posts: 26
Bikes: Specialized Expedition 08
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I need some advice on rear wheel issue...
I have a comfort bike with entry level Alex z1000 26" wheels. I started riding it 3 or 4 years ago weighing as much as 371 now 319. About a year ago it started breaking spokes and now breaks them about every 100 miles. I am commuting to work these days. 12.5 miles round trip.
I assume I will get lots of replies that I need to have a wheel specialist build a new wheel for me. Well the one I talked to quoted me $375 to by the components, build the wheel, swap out my cassette, hub, etc.
Not in my budget....
So I go out to ebay today and I see a new Alex Z1000 rear wheel for about $40 (with shipping) My question is: Do you think it is reasonable to expect that a new wheel of the same type and brand might give me a year or two of non exploding spokes like the original wheel did?
or is it a crapshoot?
I assume I will get lots of replies that I need to have a wheel specialist build a new wheel for me. Well the one I talked to quoted me $375 to by the components, build the wheel, swap out my cassette, hub, etc.
Not in my budget....
So I go out to ebay today and I see a new Alex Z1000 rear wheel for about $40 (with shipping) My question is: Do you think it is reasonable to expect that a new wheel of the same type and brand might give me a year or two of non exploding spokes like the original wheel did?
or is it a crapshoot?
#2
Senior Member
Join Date: Jan 2011
Location: South Yorkshire, England.
Posts: 247
Bikes: Colnago CX-1 Record 11sp. Carbon Epic expert 29er, Claud Butler Dalesman. Proflex X-px Works, Cougar 653. KHS Montana Pro, Hercules Alassio. Ammoco Monte Carlo F/SS. Corratec Superbow Fun 29er. Claud Butler Midas. Kenisis T2. Peugeot Perthus.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I should imagine the new wheel will be the same as the old wheel but why don't you check out stronger wheels, maybe a higher spoke count would be stronger? Maybe Alex do a wheel which is only slightly more expensive than the z1000 but has more spokes and is stronger? You'd have to take advice on this, i'm just speculating.
#3
Member
Thread Starter
Join Date: May 2011
Posts: 26
Bikes: Specialized Expedition 08
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
That is probably a good suggestion but I am ignorant as to what would be compatible with my current hardware.... if anyone would like to point me to a slightly better or stronger wheel that is compatible with my specialized expedition sport 2008. I would be grateful!
#4
Nigel
Join Date: Mar 2011
Location: San Jose, CA
Posts: 2,991
Bikes: 1980s and 1990s steel: CyclePro, Nishiki, Schwinn, SR, Trek........
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times
in
6 Posts
Hi Nazran;
Not a crap shoot; you need to build or rebuild (or have someone do it for you) a wheel with properly tensioned spokes.
Personally; I would get this wheel:
https://www.amazon.com/Alex-shimano-A...6820369&sr=1-3
and this spacer for your 7 speed cassette to fit properly on the 8/9 speed freehub:
https://www.amazon.com/Avenir-7Spd-Ca...6820485&sr=1-2
(note get both from Niagara to save on shipping).
And then re-tension and stress relieve the spokes.
This is what I found on your bike:
https://www.bikepedia.com/quickbike/B...port&Type=bike
The 36 spoke wheel will be stronger.
You don't mention where you are, but I have a wheel that will fit you bike that will not have a spoke failure; it has 36 Wheelsmith DH13 spokes; properly tensioned, stress relieved and trued.
Not a crap shoot; you need to build or rebuild (or have someone do it for you) a wheel with properly tensioned spokes.
Personally; I would get this wheel:
https://www.amazon.com/Alex-shimano-A...6820369&sr=1-3
and this spacer for your 7 speed cassette to fit properly on the 8/9 speed freehub:
https://www.amazon.com/Avenir-7Spd-Ca...6820485&sr=1-2
(note get both from Niagara to save on shipping).
And then re-tension and stress relieve the spokes.
This is what I found on your bike:
https://www.bikepedia.com/quickbike/B...port&Type=bike
The 36 spoke wheel will be stronger.
You don't mention where you are, but I have a wheel that will fit you bike that will not have a spoke failure; it has 36 Wheelsmith DH13 spokes; properly tensioned, stress relieved and trued.
#5
Member
Thread Starter
Join Date: May 2011
Posts: 26
Bikes: Specialized Expedition 08
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Hi Nigel, thank you for the suggestions. I live in Texas. I'm a complete newb, but what is the spacer for?
#6
Senior Member
Join Date: Aug 2011
Posts: 179
Bikes: 2006 DBR Podium 2
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I recommend getting wheels stronger than the originals, especially for a big guy like you. (and like me). I have no suggestions though. I am getting some of those expensive custom wheels. A higher spoke count is always good though.
#7
Nigel
Join Date: Mar 2011
Location: San Jose, CA
Posts: 2,991
Bikes: 1980s and 1990s steel: CyclePro, Nishiki, Schwinn, SR, Trek........
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
Quoted: 384 Post(s)
Likes: 0
Liked 6 Times
in
6 Posts
7 speed cassettes are 4.5mm narrower than 8 and 9 speed cassettes. It is very difficult (old stock only) to find a 7 speed free hub, or wheel with a 7 speed free hub to accept your 7 speed cassette; thus the spacer solution.
#8
Senior Member
Join Date: Dec 2010
Location: northern Deep South
Posts: 8,904
Bikes: Fuji Touring, Novara Randonee
Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 2604 Post(s)
Liked 1,933 Times
in
1,213 Posts
So I go out to ebay today and I see a new Alex Z1000 rear wheel for about $40 (with shipping) My question is: Do you think it is reasonable to expect that a new wheel of the same type and brand might give me a year or two of non exploding spokes like the original wheel did?
or is it a crapshoot?
or is it a crapshoot?
To expound a bit further, buying a machine-built wheel is the cheapest way to get the parts. The build is just about guaranteed to be awful. That's why you need to get someone who knows how to build a wheel to do what the machine didn't -- the machine gets it round, but the spokes aren't tensioned correctly, so they'll unscrew, or fatigue and break. $50 is the going rate around here, so +/- $20, and that C-note should give you a wheel that should last a long time with minimal problems.