Go Back  Bike Forums > Bike Forums > Commuting
Reload this Page >

Lights for Riding in the Dark

Search
Notices
Commuting Bicycle commuting is easier than you think, before you know it, you'll be hooked. Learn the tips, hints, equipment, safety requirements for safely riding your bike to work.

Lights for Riding in the Dark

Thread Tools
 
Search this Thread
 
Old 11-07-11, 05:21 AM
  #1  
Senior Member
Thread Starter
 
Join Date: Jul 2011
Location: cherry hill, nj
Posts: 6,144
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 32 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Lights for Riding in the Dark

Wanted to get everyones opinion.

Will be starting to commute in the dark to and from work. Looking for a light that has a lot of lumens. I would think the brighter the better. Any suggestions?

Heard some people have a front light and also a helmet light. Opinions?
Heard some people use to blinkies on the back.... opinions?

suggestions, opinons, and ideas along with advise.... all welcome!
chefisaac is offline  
Old 11-07-11, 05:44 AM
  #2  
Bicikli Huszár
 
sudo bike's Avatar
 
Join Date: Jan 2010
Location: Fresno, CA
Posts: 2,116

Bikes: '95 Novara Randonee

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
My set up is a Planet Bike Superflash for the rear. The brightness seems to be a good bang for the buck, and it has a catchy flash pattern (or steady mode). I'm happy with it. Pretty confident anyone approaching can see me clearly. I've seen other cyclists using this a mile away, literally (it can be a bit bright for those behind you on a group ride, but steady mode seems to make it bearable).


And, recommended to me by scoatw, a Romisen RC-N3 II Cree flashlight for the front with a simple flashlight mount. It's handy because with the extender tube you can just use rechargeable AA's, and you also have a really powerful flashlight, for comparatively cheap (or if you like the smaller form factor, I suppose you could get a rechargeable CR123A, which is like a camera battery). Definitely not just a "be seen" light... it's bright enough to ride by in pitch dark. I'm really happy with it. Can't say enough about it, really. I can post pics of my setup later.



Last edited by sudo bike; 11-07-11 at 06:01 AM.
sudo bike is offline  
Old 11-07-11, 06:24 AM
  #3  
Senior Member
 
Join Date: Jul 2011
Posts: 621
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Two lights on the back - always. A light can stop working with little warning, certainly no noise.

The above only applies to Lights for Riding in the Dark. Lights for riding in the Bright of Day - it don't matter so much. ; )
jolly_ross is offline  
Old 11-07-11, 07:44 AM
  #4  
Senior Member
 
Join Date: Feb 2004
Location: No Va
Posts: 117
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Check the Electronics, Lighting & Gadgets subforum for more opinions than you can handle.

Redundancy is good. Most riders I see (myself included) have two lights in the back. I have one on the frame in steady mode and one on my backpack in blinkie mode. More lights can't hurt.

Lots of variables for headlights - lumens and light pattern are both important, and there are power source choices (generator / battery, rechargeable / throw away, internal / external). And again, redundancy is good. My main light (brightest) is on my handlebar. I have a "to be seen" light on my helmet.

I have a spare light in my backpack that will go in either white or red mode that I could strap anywhere I may need it.

DON'T place a red light facing forward.
ArtM is offline  
Old 11-07-11, 07:54 AM
  #5  
Resident smartass.
 
Fargo Wolf's Avatar
 
Join Date: Nov 2011
Location: Kamloops, BC, Canada
Posts: 488
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 32 Post(s)
Liked 2 Times in 2 Posts
All my stuff is Supercycle (the ONLY brand available at Canadian Tire) Two LED headlights (slightly smaller than a compact flashlight, but still really bright) mounted to the handle bar and a generator driven one mounted down lower, where the front brake attaches to the frame. For the rear, two LEDs attached to my rack top bag and one attached to my seat post. I also have one attached to my helmet now.
Fargo Wolf is offline  
Old 11-07-11, 10:34 AM
  #6  
Old, but not really wise
 
CptjohnC's Avatar
 
Join Date: Jul 2010
Location: Fairfax, VA commuting to Washington DC
Posts: 814

Bikes: 2010 Kona Dew Drop (the daily driver),'07 Specialized Roubaix (the sports car), '99 ish Kona NuNu MTB (the SUV), Schwinn High Plains (circa 1992?) (the beater)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I run two tactical flashlights -- on on my bars and one on my helmet (plus I carry a 'reserve' light in the panniers). I also run a flashing red light on the back of my helmet, a steady red light on the back of my rack, and one more blinky on the back of my panniers (with red reserve in the panniers, as well).

In full daylight, I generally don't bother much with lights, because in my opinion, they really add very little as compared to high vis clothing (I wear a reflective, hi-vis orange vest or hi vis t-shirts in summer, and a hi vis jacket w/ reflective accents in winter). I base this on what I see as a fellow cyclist approaching, as well as my experience as a driver coming up on cyclists.

I do run some or all lights during any periods of diminished light (fog, dawn/dusk, clouds, or when I know I'll be passing through tunnels or underpasses, or even streets that are particularly tree lined).

As a cheap solution for the front that is better than the typical walmart/target offerings, I would advocate for the tactical flashlights available from Costco (if you're a member) -- its a 3 pack of nominal 150 lumen lights for like $15. These are bright enough to 'see' by if you keep your speeds really modest, though you won't get the kind of road detail you really need for traversing unknown or serious dark streets. I use them on some unlighted stretches of MUP with reasonable comfort at speeds near 10MPH. One nice thing about mounting one to the helmet is that you can point the hot spot where you need it. They also have a pretty good flash mode for the 'to be seen' aspect. Not a perfect solution, but better than most offerings near the price. NOTE: These are NOT the tactical flashlights offered on Costco.com for a lot more money. I have not tried those.
CptjohnC is offline  
Old 11-07-11, 10:55 AM
  #7  
Noobie of the year :)
 
MijnWraak's Avatar
 
Join Date: Jul 2009
Location: Hour South of Boston
Posts: 287

Bikes: 1980's Miyata Seven Ten

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I'm in love with my Magicshine setup. The rear light is only $30 (+ battery costs), but can be seen literally a mile away, and lasts about 3 weeks on one charge. The headlight is excellent for my needs and is wicked bright, but drains its battery fairly quickly. I only ride at night 2/3 nights a week.
MijnWraak is offline  
Old 11-07-11, 11:18 AM
  #8  
Mirror slap survivor
 
Join Date: Apr 2005
Location: Sunny Florida
Posts: 1,297

Bikes: Gunnar Sport, Surly Pacer, Access MTB, Ibex Corrida, one day a Simple City

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
There are too many options to list, and most of them are good nowadays. LED headlight technology is fully mature. You are only limited by your budget. The tactical flashlights with a TwoFish block are excellent. I've heard good things about the Magicshine lights.

I use a DiNotte 600L up front, a DiNotte 140 on my helmet, a DiNotte taillight on the seatpost, a Planet Bike Superflash on the blinkie strap on the rear of my helmet, and a reflective LED vest.
Schwinnrider is offline  
Old 11-07-11, 11:31 AM
  #9  
Senior Member
 
Join Date: May 2008
Posts: 204
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Dinotte 800L up front and a 140r mounted to the seat rails.
kaseri is offline  
Old 11-07-11, 11:59 AM
  #10  
Senior Member
 
tarwheel's Avatar
 
Join Date: May 2007
Location: Raleigh, NC
Posts: 8,896

Bikes: Waterford RST-22, Bob Jackson World Tour, Ritchey Breakaway Cross, Soma Saga, De Bernardi SL, Specialized Sequoia

Mentioned: 36 Post(s)
Tagged: 0 Thread(s)
Quoted: 196 Post(s)
Likes: 0
Liked 6 Times in 4 Posts
There are lots of great options these days for LED lights. Like Schwinnrider said, your budget is your only limit. I also agree that redundancy is important. I use at least two helmet and bar/frame mount lights, front and rear. If you are trying to keep costs down, some good options for headlights are Magicshine, Nightrider Minewt 600, Dinotte, Light & Motion Stella series, Fenix and other flashlights. PB Superflash is hard to beat for an inexpensive tail-light.
tarwheel is offline  
Old 11-07-11, 12:16 PM
  #11  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,355 Times in 862 Posts
Schmidt hub dynamo, E6 halogen bulb headlight , B&M 4D topmount rear light.
Now, 2 bikes, recently placed the battery operated rear light, on my BikeFriday,
that came off my Koga WTR, Tubus Logo rear rack,..
when I added a wired into the headlight ..one in its place..

Clever kludge: , I made a light mount for the 2 bolt Euro taillight,
that was fitted onto the low, rear of the seatpost water bottle cage,
[used Zefal mudguard struts, for the project]

So as to not cover my lights with my Rain Cape ,

when I ride thru the Downpour.. North Pacific Coastal storms do that ..

Last edited by fietsbob; 11-07-11 at 03:11 PM.
fietsbob is offline  
Old 11-07-11, 01:59 PM
  #12  
Junior Member
 
Join Date: Oct 2010
Location: Redmond WA
Posts: 123
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by MijnWraak
I'm in love with my Magicshine setup.
Same here. I have the battery on my rack, it powers the front and rear lights. The front light is dimmable so that I can light up the unlit paths I ride on but tone it down for oncoming traffic, the tail light is superb. I got mine from Geomangear and am on my second season with the same setup, use it 4 days a week coming and going.
drbenjamin is offline  
Old 11-07-11, 02:22 PM
  #13  
smitten by саша
 
pwdeegan's Avatar
 
Join Date: Sep 2008
Location: Eugene, OR
Posts: 523

Bikes: Salsa La Cruz with Rohloff; mutt parts

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by fietsbob
Schmidt hub dynamo, E6 halogen bulb headlight , B&M 4D topmount rear light.
Now, 2 bikes, recently placed the battery operated rear light, on my BikeFriday,
that came off my Koga WTR, rear rack,.. when I added a wired into the headlight
one in its place..
Clever kludge: , I made a light mount for the 2 bolt Euro taillight, that was fitted
onto the low, rear of the seatpost water bottle cage,
[used Zefal mudguard struts, for the project]

So as to not cover my lights with my Rain Cape ,

when I ride thru the Downpour.. North Pacific Coastal storms do that ..
+1 on the dynohub setup. I relied on battery-powered LEDs for years, which are nice and bright. But creating bag fulls of dead batteries, or the hassle of trying to replace proprietary recharables (I had an old NiteRider setup; the rechargeable finally only provided power for about 15 minutes) depressed me. Over the long haul, you break even (or even save money) by buying a good dynohub and pairing it with a good LED lamp.

I still use battery-powered LEDs, but usually only as backups, as in a helmet mount light during the darkest moments (forest paths, black MUPs), or in the rare case of wanting to stand out even more to traffic (the Sauron-like swiveling 2W LED spotlight). In any event, I'm not generating bags of battery waste any longer.
pwdeegan is offline  
Old 11-07-11, 02:25 PM
  #14  
Senior Member
 
Kojak's Avatar
 
Join Date: Feb 2009
Location: PNW - Victoria, BC
Posts: 1,486

Bikes: 2002 Litespeed Vortex - 2007 Trek Madone 5.9 - 2004 Redline Conquest Pro - Specialized S-Works Festina Team Model - 93 Cannondale M 800 Beast of the East

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 6 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I sure liked my Light and Motion Stella 400 set up until some scumbag stole the set up off my bike. I think it's now the Stella 600, which I'll get as a replacement.

I hate scumbag thieves.
Kojak is offline  
Old 11-07-11, 02:37 PM
  #15  
Senior Member
 
Monster Pete's Avatar
 
Join Date: Apr 2010
Location: Warwick, UK
Posts: 1,049

Bikes: 2000-something 3 speed commuter, 1990-something Raleigh Scorpion

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
A bright light is good, but you also want a fairly wide viewing angle so you can see/be seen at positions other than head-on/directly behind. A dynohub with LED lights is virtually a 'fit and forget' solution as with proper voltage regulation LEDs last virtually forever. A head torch or helmet-mounted light (as applicable) gives you a bit of redundancy and extra light, and of course points wherever you're looking.

It largely depends where you're riding. In well-lit streets, lighting is basically there to make you visible rather than to light the way, and smaller, wide-angle lights will suffice. On unlit trails etc, you are mainly lighting the way, so should ideally have a bright, focused headlight in addition to your wide-angle headlight.
Monster Pete is offline  
Old 11-07-11, 02:38 PM
  #16  
Senior Member
 
Join Date: Oct 2011
Posts: 74
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Anybody try the Lezyne Super Drive? MSRP is $109.00. Many online stores are selling it for quite a bit more but it is available on the manufacturers online store for $109. Like the look. Hear they generally make good products. And I like that it runs off of an 18650 battery. 450 lumens is certainly enough for my needs (commuting on familiar paths at modest speeds). The battery is the main reason I want this light over comparable lights by other manufacturers. I can buy a spare for 10 bucks. And have 2 high capacity lithium-ion batteries without paying an arm and a leg for a proprietary design.

So...anybody with experience with this light?


(Edit): So just looked at those Romisen lights. They look like an EXCELLENT value. Might pull the trigger on one of those if Costco doesn't get the 3 flashlight pack in the next couple weeks. (thought I could mount two of the Costco ones for decent output).

Last edited by fizbiz; 11-07-11 at 02:57 PM.
fizbiz is offline  
Old 11-07-11, 03:24 PM
  #17  
xtrajack
 
xtrajack's Avatar
 
Join Date: Aug 2008
Location: Maine
Posts: 2,058

Bikes: Kona fire mountain/xtracycle,Univega landrover fs,Nishiki custom sport Ross professional super gran tour Schwinn Mesa (future Xtracycle donor bike)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I used the Magicshine for a while. I liked the output, I wound up having battery issues with it. I also had issues with the light head itself (switch malfunction, wouldn't always work, to the point that I lost confidence in it).

I switched to a sidewall generator set-up (B+M Dymotec and B+M Lumotec IQ Fly+, from Peter White, linked to above), while not as as bright as the Magicshine, it provides an adequate amount of light for a "to see with light" because it is focused better. It always works, no issues at all in over a year of use. I also have a 105 lumen (rated by mfg.) helmet light.

On the back I have a PBSF and 2 generic blinkies, all on steady mode.
xtrajack is offline  
Old 11-07-11, 04:06 PM
  #18  
Senior Member
 
canyoneagle's Avatar
 
Join Date: Nov 2007
Location: Santa Fe, NM
Posts: 4,599

Bikes: Vassago Moosknuckle Ti 29+ XTR, 90's Merckx Corsa-01 9sp Record, PROJECT: 1954 Frejus SuperCorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 174 Post(s)
Liked 157 Times in 75 Posts
Originally Posted by jolly_ross
Two lights on the back - always. A light can stop working with little warning, certainly no noise.

The above only applies to Lights for Riding in the Dark. Lights for riding in the Bright of Day - it don't matter so much. ; )
I'll play devil's advocate - at night, my reflective stuff will shine even if my rear lights (both of them) fail. At night the contrast is much greater so cyclists REALLY stand out.
During the day, cyclists easily disappear into the rest of the scenery, and blinkies help increase the chances that the cyclists are seen. Hi viz clothing can help, but I find that I notice active lighting moreso than hi viz colors.

OP - the best bang for the buck IMO is a flashlight (with a Cree LED) up front with a really good blinkie (PB superflash turbo) in the rear, with a more basic secondary rear blinkie.

I also run a bright (white) blinkie up front whenever I ride - it has saved my butt numerous times (drivers double taking and hitting brakes when entering from side streets or turning from the opposite direction).

I presently run a double setup - set #1 is a dynamo hub driving a Supernova E3 Pro "asymmetrical lens" headlight and its accompanying steady 3 LED tail light. The lens offers a better light dispersion at the cost of some absolute lumens.
Set #2 is a Planet Bike Blaze 2W up front on blink mode (always) and a Planet Bike (PB) Superflash Turbo on blink in the rear.

I used a magicshine for a year or so, and it was really bright. The light pattern (at the time, things may be better) had a huge hotspot, but the light was awesome for the money.
Despite the fact that the Magicshine is probably 2x brighter than my E3 Pro, I prefer the dispersion of the Supernova much better. No appreciable hotspots, bright enough to see very well, wide beam.
The Supernova "triple" is the high wattage dynamo offering that is recommended only for offroad use, but it would be interesting to compare with the Magicshine and other LED-based 700-1100 "claimed" Lumen lights to see how the beams compare. I've seen Peter White's site, which is nice, but he's only listed the lights he sells.

Last edited by canyoneagle; 11-07-11 at 04:22 PM.
canyoneagle is offline  
Old 11-07-11, 04:18 PM
  #19  
bored of "Senior Member"
 
Join Date: Oct 2007
Location: MD / metro DC
Posts: 2,883

Bikes: Cross-Check/Nexus commuter. Several others for various forms of play.

Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 642 Post(s)
Liked 593 Times in 453 Posts
Originally Posted by chefisaac
Wanted to get everyones opinion.

Will be starting to commute in the dark to and from work. Looking for a light that has a lot of lumens. I would think the brighter the better. Any suggestions?

Heard some people have a front light and also a helmet light. Opinions?
Heard some people use to blinkies on the back.... opinions?

suggestions, opinons, and ideas along with advise.... all welcome!
Yes, that's been my experience, too. They do work best for riding in the dark. The lights with more lumens do tend to be brighter, and I have seen many people with blinkies on the back as well as a few with helmet lights.

The ones I can't figure are the ones with front blinkies. After about 30 sec of that I'd be looking for a stick to put between my teeth so I wouldn't swallow my tongue.
slcbob is offline  
Old 11-07-11, 06:30 PM
  #20  
Senior Member
 
bhop's Avatar
 
Join Date: Jun 2008
Location: Los Angeles
Posts: 1,894

Bikes: Bianchi Via Nirone 7, Jamis Sputnik

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Magicshine rules. I got high beamed by a car the other day when mine was set to high. It's pretty damned bright. I use two planet bike superflash in the back, one on the bike, one on my backpack.
bhop is offline  
Old 11-07-11, 06:38 PM
  #21  
In the right lane
 
gerv's Avatar
 
Join Date: Dec 2005
Location: Des Moines
Posts: 9,557

Bikes: 1974 Huffy 3 speed

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 44 Post(s)
Liked 7 Times in 6 Posts
Originally Posted by pwdeegan
Over the long haul, you break even (or even save money) by buying a good dynohub and pairing it with a good LED lamp.
I really don't understand why more cyclists don't use dynohubs. I find the light more than adequate for my purposes and you can now buy lights in the 2-3 watt range that are well suited to even fast riding.

But the real clincher is that you don't have to change a battery or recharge anything. Oftentimes, you don't even have to switch it on.

Very convenient.
gerv is offline  
Old 11-07-11, 06:50 PM
  #22  
Junior Member
 
Join Date: Oct 2010
Location: Redmond WA
Posts: 123
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by gerv
I really don't understand why more cyclists don't use dynohubs.
Back in the day I used a sidewall bottle dynamo, and I disliked how the lights would turn off when I stopped (which is when I most want them on, many stops are at traffic lights and intersections). People used to rig up large capacitors to power the lights through stops, but I'm not electrically inclined enough to DIY. Are any of the modern dyno solutions equipped with reserve capcity to keep the lights on during stops?
drbenjamin is offline  
Old 11-07-11, 07:20 PM
  #23  
nashcommguy
 
Join Date: Feb 2006
Location: nashville, tn
Posts: 2,499

Bikes: Commuters: Fuji Delray road, Fuji Discovery mtb...Touring: Softride Traveler...Road: C-dale SR300

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Recently purchased a Niterider Mi-Newt 150 cordless, re-chargable headlight from https://www.nashbar.com for 70.00. It's a phenomenal light for the money. Too bright on high beam. I use it on it's lowest setting. It has a nice, tight light barrell. The strobe mode flashes between off and the highest setting...WAY too intense. Use a dimmer light w/a strobe option for that purpose. Mine's a Sette Glo available from https://www.pricepoint.com for 9.00US. Takes 3 AAA batteries.

For rear lights I use Sette blinkies which are PBSF knockoffs, but just as bright. I've got a couple of SFs and can discern no appreciable difference in the brightness. 3 modes. They're 9.00US as well from PP.com.

Have been using NR Trailrat 2.0 for years and they all gave out around the same time. I found a guy on e-bay who re-built them for a very good price, so I'm still using them even though the Mi-Newt is a vastly superior light...old habits die hard.
nashcommguy is offline  
Old 11-07-11, 09:13 PM
  #24  
Senior Member
 
devianb's Avatar
 
Join Date: Dec 2007
Location: Central Illinois
Posts: 869

Bikes: 2008 Dawes Haymaker 20XX Leader LD515 TotoCycling Road Bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 27 Post(s)
Likes: 0
Liked 32 Times in 19 Posts
I don't have a good recommendation for the front light, but for the rear I like the Radbot 500, although I hear the Radbot 1000 is much brighter. It is small, quite visible, different modes, only uses 2 aaa batteries, you can't accidentally turn it on if it is in your bag, not too expensive, and it looks good.
devianb is offline  
Old 11-07-11, 10:02 PM
  #25  
Senior Member
 
Join Date: Jul 2011
Location: Minneapolis, MN
Posts: 199

Bikes: Trek Allant

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by drbenjamin
Are any of the modern dyno solutions equipped with reserve capcity to keep the lights on during stops?
All of the B&M lights with "plus" in their names, and the newer ones like the Lumotec IQ CYO RT, have this feature, as do their taillights.
FanaticMN is offline  


Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.