Belt Drive and Fixing a Flat
#1
Senior Member
Thread Starter
Join Date: Jun 2004
Posts: 74
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Belt Drive and Fixing a Flat
Hi Folks,
I'm starting to consider a belt drive for my next bike, and I'm curious about something that doesn't seem to get a lot of coverage. How challenging is it to fix a rear flat? More specifically, is it easy enough to remove the rear wheel while on the road? Or does a flat necessitate a call to AAA ;^) ? Presumably that depends at least somewhat on the specific frame. Are there particular hangers or other approaches that make it easy or hard?
Thanks in advance,
Stephen
Updated with additional comments below
Thanks to folks for the replies. The original post should have noted that I was wondering about an IGH along with a belt drive. My main questions are the difficulty of aligning and tensioning the belt correctly. From the comments it seems like it's manageable on the road with a little practice in advance.
I'm starting to consider a belt drive for my next bike, and I'm curious about something that doesn't seem to get a lot of coverage. How challenging is it to fix a rear flat? More specifically, is it easy enough to remove the rear wheel while on the road? Or does a flat necessitate a call to AAA ;^) ? Presumably that depends at least somewhat on the specific frame. Are there particular hangers or other approaches that make it easy or hard?
Thanks in advance,
Stephen
Updated with additional comments below
Thanks to folks for the replies. The original post should have noted that I was wondering about an IGH along with a belt drive. My main questions are the difficulty of aligning and tensioning the belt correctly. From the comments it seems like it's manageable on the road with a little practice in advance.
Last edited by sathomasga; 05-09-14 at 06:57 AM. Reason: Update
#2
OlyCommuter
Join Date: Dec 2004
Location: Olympia, WA
Posts: 175
Bikes: Spot Ajax for commuting, Jamis Dakota Sport for dirt.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The belt itself doesn't make wheel removal any more difficult than with a chain. But most belt-drive bikes use an IGH on the rear wheel (unless it's a single speed bike). This means that when you remove the wheel, you are also removing the gear unit, and that in turn means you need to disconnect the cable from the IGH first. It's not a big deal, just read through the procedure once or twice, maybe practice it once at home and you'll get it. It's most easily done with the bike upside down.
#3
No one carries the DogBoy
Most flats don't require removing the wheel.
These are the steps I learned riding a horizontal drop bike with fenders, an IGH and a fully covered crankcase.
1. Pull tire off one side of rim.
2. Locate hole in tube
3. Check tire for obstruction that caused hole in tube.
4. Remove obstruction in tire
5. Patch hole in tube.
6. Reinstall the tire on the rim
7. Inflate
8. Carry on.
These are the steps I learned riding a horizontal drop bike with fenders, an IGH and a fully covered crankcase.
1. Pull tire off one side of rim.
2. Locate hole in tube
3. Check tire for obstruction that caused hole in tube.
4. Remove obstruction in tire
5. Patch hole in tube.
6. Reinstall the tire on the rim
7. Inflate
8. Carry on.
#4
Formerly Known as Newbie
Join Date: Mar 2002
Location: Helsinki, Finland
Posts: 6,249
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 4 Times
in
3 Posts
Getting slightly off-topic, but that's not always the case with IGH. If the cable housing is attached to the frame with QR tabs, you can often get enough slack to remove the wheel by simply de-attaching (is that even a word?) the housing from the first 2-3 tabs.
Regarding frames, don't all belt driven bikes come with a break in drive side rear triangle, otherwise you wouldn't be able to remove or install the belt?
--J
Regarding frames, don't all belt driven bikes come with a break in drive side rear triangle, otherwise you wouldn't be able to remove or install the belt?
--J
__________________
To err is human. To moo is bovine.
Who is this General Failure anyway, and why is he reading my drive?
Become a Registered Member in Bike Forums
Community guidelines
To err is human. To moo is bovine.
Who is this General Failure anyway, and why is he reading my drive?
Become a Registered Member in Bike Forums
Community guidelines
#5
Senior Member
Some tires are easier to get back on than others. You may not be able to reinstall a difficult tire without removing the wheel. Finding the cause of the puncture is sometimes easy, sometimes difficult. Finding the difficult culprits is much easier with the wheel off the bike. With a large puncture or tear at the valve stem, a patch may not work. In the wet, a patch may not adhere. You may need to replace the tube, which requires removing the wheel.
I always remove the wheel for reparing a flat, but don't use a belt drive or IGH.
I always remove the wheel for reparing a flat, but don't use a belt drive or IGH.
#7
No one carries the DogBoy
Some tires are easier to get back on than others. You may not be able to reinstall a difficult tire without removing the wheel. Finding the cause of the puncture is sometimes easy, sometimes difficult. Finding the difficult culprits is much easier with the wheel off the bike. With a large puncture or tear at the valve stem, a patch may not work. In the wet, a patch may not adhere. You may need to replace the tube, which requires removing the wheel.
I always remove the wheel for reparing a flat, but don't use a belt drive or IGH.
I always remove the wheel for reparing a flat, but don't use a belt drive or IGH.
#8
OlyCommuter
Join Date: Dec 2004
Location: Olympia, WA
Posts: 175
Bikes: Spot Ajax for commuting, Jamis Dakota Sport for dirt.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Getting slightly off-topic, but that's not always the case with IGH. If the cable housing is attached to the frame with QR tabs, you can often get enough slack to remove the wheel by simply de-attaching (is that even a word?) the housing from the first 2-3 tabs.
Regarding frames, don't all belt driven bikes come with a break in drive side rear triangle, otherwise you wouldn't be able to remove or install the belt?
--J
Regarding frames, don't all belt driven bikes come with a break in drive side rear triangle, otherwise you wouldn't be able to remove or install the belt?
--J
And yes, you do need a break in the rear triangle to remove/reinstall the belt, but fortunately you don't have to do that to change a flat. I've had my Spot Ajax for almost two years and have never had to remove the belt. And only had one flat, then mounted some Schwalbe Marathons. Smooth riding since.
#9
contiuniously variable
On shimano hubs the cable can be unhooked in like .5 seconds, it has a lil directional screw that clamps down on the end & anchors into a slot, just pop it out of slot and you're golden. Be sure to thread the cable around the hub properly when re-instaling, or you'll end up not shifting correctly & possibly damaging the mechanisms inside.
- Andy
- Andy
#10
♋ ☮♂ ☭ ☯
Join Date: Feb 2005
Location: 40205 'ViLLeBiLLie
Posts: 7,902
Bikes: Sngl Spd's, 70's- 80's vintage, D-tube Folder
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
This is kind of elementary, but everyone should do a dry-run flat repair on any new bike and immediately pick up all the stuff you used and throw it in you bike bag.
Not very much fun on the side of the road wondering about something as the sun is going d
.................................................................................................... .........................o
.................................................................................................... .............................w
.................................................................................................... ................................n
.................................................................................................... .................................
That also means some cheap readers for we oLde people
But I agree with the posts about not removing the wheel at all once you learn your bike. I havent had a flat that required a tube/rim removal in almost a decade. KoW!
Not very much fun on the side of the road wondering about something as the sun is going d
.................................................................................................... .........................o
.................................................................................................... .............................w
.................................................................................................... ................................n
.................................................................................................... .................................
That also means some cheap readers for we oLde people
But I agree with the posts about not removing the wheel at all once you learn your bike. I havent had a flat that required a tube/rim removal in almost a decade. KoW!
__________________
☞-ADVOCACY-☜ Radical VC = Car people on bikes. Just say "NO"
☞-ADVOCACY-☜ Radical VC = Car people on bikes. Just say "NO"
#11
Banned
Join Date: Feb 2008
Location: Mississauga/Toronto, Ontario canada
Posts: 8,721
Bikes: I have 3 singlespeed/fixed gear bikes
Mentioned: 30 Post(s)
Tagged: 0 Thread(s)
Quoted: 4227 Post(s)
Liked 2,488 Times
in
1,286 Posts
The biggest problem with belt drives is that the rear wheel has to be 100% centered and aligned in the rear drop outs or else the belt will keep falling off the rear sprocket. This was a problem when the belt drives first came out. I don't know if the manufacturers corrected the problem or not...There is nothing wrong with chain drives. Chains are simple and easy to maintain or replace when they wear out. Why waste money on something that has no advantages...As for patching a tube without removing a wheel. Really ?? ...Try patching your tube in sub-freezing temps with snow and sleet or pouring rain.
#12
contiuniously variable
The biggest problem with belt drives is that the rear wheel has to be 100% centered and aligned in the rear drop outs or else the belt will keep falling off the rear sprocket. This was a problem when the belt drives first came out. I don't know if the manufacturers corrected the problem or not...There is nothing wrong with chain drives. Chains are simple and easy to maintain or replace when they wear out. Why waste money on something that has no advantages...As for patching a tube without removing a wheel. Really ?? ...Try patching your tube in sub-freezing temps with snow and sleet or pouring rain.
As for belts vs chains, chains are noisier, and stretch and corrode and wear the teeth of the ring & sprocket out. Belts, especially the center track design, have nowhere for debris and road go to sit, so now it's even simpler to maintain.
As for patching tubes, i don't think anything involving elastic and adhesive should be done below 38-42 degrees...
- Andy
Last edited by TransitBiker; 05-08-14 at 03:05 AM.
#14
contiuniously variable
- Andy
#15
Senior Member
Join Date: Jun 2007
Location: Minneapolis
Posts: 8,101
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 52 Post(s)
Likes: 0
Liked 17 Times
in
13 Posts
Again, that's with a new, clean chain. To me a belt drive is attractive because it is less effected by exposure to the elements. My chains can be in pretty rough shape during the winter between cleanings and I'm guessing a rubber band might be more efficient at times.
#16
Mostly harmless ™
Join Date: Nov 2010
Location: Novi Sad
Posts: 4,430
Bikes: Heavy, with friction shifters
Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1107 Post(s)
Liked 216 Times
in
130 Posts
That's true with a perfectly clean new chain and the way the Gates system is recommended to be set up (with a tension preload). If the belt drive system were to use no pre-load and a tensioner instead, the belt system would become more efficient once the rider starts putting out 200 watts or more.
Again, that's with a new, clean chain. To me a belt drive is attractive because it is less effected by exposure to the elements. My chains can be in pretty rough shape during the winter between cleanings and I'm guessing a rubber band might be more efficient at times.
Again, that's with a new, clean chain. To me a belt drive is attractive because it is less effected by exposure to the elements. My chains can be in pretty rough shape during the winter between cleanings and I'm guessing a rubber band might be more efficient at times.
#17
Senior Member
Join Date: Mar 2006
Location: Montgomery County, Pennsylvania
Posts: 6,489
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 6 Times
in
2 Posts
Good thread. It's giving me some things to think about. I've thought on and off about belt drives and hope others jump into the thread with what they know.
__________________
A conclusion is the place where you got tired of thinking. - S. Wright
Favorite rides in the stable: Indy Fab CJ Ti - Colnago MXL - S-Works Roubaix - Habanero Team Issue - Jamis Eclipse carbon/831
A conclusion is the place where you got tired of thinking. - S. Wright
Favorite rides in the stable: Indy Fab CJ Ti - Colnago MXL - S-Works Roubaix - Habanero Team Issue - Jamis Eclipse carbon/831
#18
OlyCommuter
Join Date: Dec 2004
Location: Olympia, WA
Posts: 175
Bikes: Spot Ajax for commuting, Jamis Dakota Sport for dirt.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#19
Banned
With experience comes wisdom.
#20
Senior Member
Not that interested in belt drives for the sake of having a belt drive but one of my dream commuters (aluboo commuter) has a belt drive and the break is at the bolt on drop outs.
I have seen most of the new ones similar to this, though this isn't an aluboo.
which really isn't that new of a technology. I have a '59 magneet that unbolts at the end of the rear triangle, it has been around for many miles before I found it and everything still holds together.
I have seen most of the new ones similar to this, though this isn't an aluboo.
which really isn't that new of a technology. I have a '59 magneet that unbolts at the end of the rear triangle, it has been around for many miles before I found it and everything still holds together.
#21
aka Phil Jungels
When I was a kid, we didn't have quick releases. Everything was nutted.
We always just laid the bike on it's side, removed the tire, fixed the problem, and pushed it to the nearest gas station for more air.
Worked every time - no problem.
But, I'm old!
We always just laid the bike on it's side, removed the tire, fixed the problem, and pushed it to the nearest gas station for more air.
Worked every time - no problem.
But, I'm old!
#22
Junior Member
Join Date: Dec 2014
Posts: 7
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I had the same question when considering a belt drive bike. I found a video that demonstrates exactly how it's done with a Spot Brand bike, so I thought I would add it to this old thread so future searchers can see it: acme-ajax tech 720p on Vimeo
I ended up buying a Spot Acme. They are well designed for belt drive. The only thing I needed was a 15mm wrench multitool to get the back wheel off when out on the road. One of several fixie tools will do the job (Topeak Urban 8 or Nutter tools are great).
The one thing I would recommend confirming before buying a bike is whether re-tensioning is required when removing the wheel. The Spots don't need it, but some others do - and that requires more tools and complexity. According to joe-bike.com, the Raleigh Cadent requires re-tensioning.
I ended up buying a Spot Acme. They are well designed for belt drive. The only thing I needed was a 15mm wrench multitool to get the back wheel off when out on the road. One of several fixie tools will do the job (Topeak Urban 8 or Nutter tools are great).
The one thing I would recommend confirming before buying a bike is whether re-tensioning is required when removing the wheel. The Spots don't need it, but some others do - and that requires more tools and complexity. According to joe-bike.com, the Raleigh Cadent requires re-tensioning.
#23
Senior Member
Join Date: Feb 2001
Location: England
Posts: 12,948
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 7 Times
in
7 Posts
Belt drives should use a vertical dropout to maintain tension. Std derailleur vertical dropouts have no way of adjusting tension, so you need either sliding vertical dropouts or eccentric bottom bracket.
Chain drive can use a horizontal dropout but tension is not so critical.
Chain drive can use a horizontal dropout but tension is not so critical.
#24
Senior Member
Join Date: Sep 2006
Location: Kansas
Posts: 2,248
Bikes: This list got too long: several ‘bents, an urban utility e-bike, and a dahon D7 that my daughter has absconded with.
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
Quoted: 363 Post(s)
Liked 66 Times
in
48 Posts
I have a belt drive coupled with an N360 on my commuter. It also has horizontal dropouts, the adjustment for tension is done that the Bottom Bracket (and in about 1500 mils I have not need to adjust it at all).
Removing the wheel is simple after removing the cables to the N360 (which is also pretty easy). It is no more complicated than removing any other single speed. The belt-break is in the chain-stay; however, it does not need to be opened for tyre changes; it only needs to be opened to replace the belt.
So, the operation is:
thats it, nothing special or hard.
Removing the wheel is simple after removing the cables to the N360 (which is also pretty easy). It is no more complicated than removing any other single speed. The belt-break is in the chain-stay; however, it does not need to be opened for tyre changes; it only needs to be opened to replace the belt.
So, the operation is:
- remove cables from hub
- loosen hub bolts
- pull wheel straight up (assuming bike is upside down)
thats it, nothing special or hard.
#25
Junior Member
Join Date: Jan 2015
Location: Chattanooga, TN
Posts: 18
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I run tubeless road tires, and carry a tire plug kit. Luckily I have only had to use it once, but it worked great. It's about the size of a co2 cannister, and fixed my flat in about a minute, didn't have to mess with the tire at all, just jammed this thing into the hole and reinflated to 100psi. On that day, I was just a few miles into a 50 mile ride, and it held air no problem for the remainder of the ride, I never had to top off the air or anything like that.
Amazon.com: Dynaplug Ultralite Tubeless Tire Repair Tool Kit, Made in USA: Automotive
Amazon.com: Dynaplug Ultralite Tubeless Tire Repair Tool Kit, Made in USA: Automotive