Forum: Bicycle Mechanics

Looking to replace my CDale Ultra with something lighter. Found something I like...the steerer is 7.75". By my measurement I have 8.00" from crown to the top edge of the stem with the spacers I want. Will the .25" pose a problem if using a compression plug? Thanks!

This pisses me off , The piece that holds the bolt for the cages into the frame broke off. Now what? i am the second owner of the bike. its a 2005 Trek Pilot 2.1 i was taking off the front cage when i noticed the screw was a bit hard to get out. i got it off and took the cage off ( getting...

I recently bought a used Campy Sirocco rear wheel to use with my Kurt trainer for the winter (to avoid having to change tires- keeping the good road tire on my Fulcrum wheel and putting a trainer tire on the old Sirocco). To my dismay, when I went to put the cassette on it, the lockring (original...

Hi all, Due to having a few problems with my left crank arm coming loose all the time (Truvativ Isoflow, square taper) I'm considering changing the whole set up. I've been looking at hollowtec type cranks, and the compatable BB's, but my bike currently has the non-external bearings set up. I...

How many miles does your bike mechanic ride each year?

I have a new Roubaix Comp with the adjustable stem. I see how to adjust the angle. My question is dropping it lower on the steerer tube. If I pull off one spacer to lower the stem, does that spacer have to go back on the top of the stem ( under the top cap)? It seem as though it does't need to. ...

i recently cleaned up my chain, and now when i am riding i feel a vibration around the crank. if i get off and roll it around, i can feel it up to my saddle when it does it. it rolls smooth up to a point and then i will feel the vibration and then it will be smooth again. i also feel it when i am...

so my primary bike is out of commission, and my backup bike currently doesn't have any wheels... so i was wondering, if i put my wheels with the 105 cassette on the backup bike with tiagra shifters, will anything bad come of this (assuming i'm using the outer 9 cogs)?

OK, i need an issue cleared up, with standards to bicycles threads (for bottom brackets). I have checked "sheldon Brown" but i really did not get my answer.. Correct me if i'm wrong: English/British/Euro: The standard MTB and road.And some BMX...

Would there be interest in a bike repair wiki? Some website where the whole community contributes to create excellent articles for everything from simple bicycle maintenance to the more complex stuff? I thought about creating one a while back, but don't want to create just another bike repair...

Hello and thanks in advance. So my problem is this. I have a small crack in the rear of the frame where the seatpost would insert on my 2003 Cervelo Soloist (alum). I have been reading in this forum about TIG welding as an option but was curious to see what other thought was the best fix. ...

I am currently trying to find a cassette and chainset to suit my new build. My current bike uses an 11-28t cassette with a 34-50t compact chainset. I find that the lowest gear this provides isn't really low enough for some hills and I find myself having to mash a bit. How much difference would...

I bought a new rim and spokes to build a new rear wheel. They calculated the spoke lengths and gave me two different length spokes: 293 for the right side, and 295 for the left side. However, the two spoke lengths look the same size when I stand them up next to each other, and they both seem to...

For a road bike with Shimano components, what book should I ask Santa to bring this year? Quality pictures & diagrams are most helpful to me. Any thoughts appreciated!

I have a couple of Campy G3 hubs off Zonda rear wheels. Can these be used with any other rims than Campy? For the price of a replacement Zonda rim I can just buy a complete wheel.

I have an Ultegra 5-bolt Triple Crank with a 10 speed cassette, and would like to replace the small 30T chainring with something in the neighborhood of a 26T ring. Anybody have any experience with this that could recommend a vendor for the chainring?