First
#1
Member
Thread Starter
Join Date: Mar 2011
Posts: 33
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
First
Been sitting on this awhile now...my first frame recently back from powder coat and built up. Nothing fancy, just very large (if the top tube were horizontal it would be a 66cm frame.) Built with a torch, some files, a bench clamp, some chunks of angle iron, and a magnetic protractor. Also a few choice words here and there. Proud to say that it came out very straight, aligned within a millimeter via string method at the seat tube, and rides very nicely, stable at low and high speeds. Best road frame I've ridden that actually fit me!
Pretty much taught myself how to do this by scouring this forum for a few months and reading the free version of Paterek, then jumped in. Had a lot of fun problem solving due to not having a lot of the specialized tools or a jig available.
Anyway, big thanks to everyone past and present here whose knowledge I gleaned!
Pretty much taught myself how to do this by scouring this forum for a few months and reading the free version of Paterek, then jumped in. Had a lot of fun problem solving due to not having a lot of the specialized tools or a jig available.
Anyway, big thanks to everyone past and present here whose knowledge I gleaned!
Last edited by jharley; 06-14-12 at 09:13 PM.
#2
Senior Member
Join Date: Feb 2004
Location: Denver, CO
Posts: 55
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Congratulations. That thing looks fantastic. I've wanted to jump into frame building for awhile now but I've been scared off by some of the professional's comments. Do you have any tips for a first time builder?
#3
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,392
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,690 Times
in
2,513 Posts
that looks really good, thanks for posting pictures
#4
Member
Thread Starter
Join Date: Mar 2011
Posts: 33
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Biggest tip is don't be scared! I believe if you read enough, think carefully, and go slow, anyone can end up with a straight, rideable bike using minimal tooling. At least as good as an off the shelf frame, but with the benefit of having enjoyed the process of making it. Keep in mind that despite the way frame building gets talked about, these things don't need to be built to aerospace tolerances. In the end, its "just" a bicycle.
I found this little clip really inspiring when I was teaching myself:
https://www.youtube.com/watch?v=TMA8X5pk2kI
The part at 3:20 when he checks alignment of the seat and headtubes by eyeball....super accurate and completely free. They don't need no stinking jig or new fangled alignment table!
Have fun!
I found this little clip really inspiring when I was teaching myself:
https://www.youtube.com/watch?v=TMA8X5pk2kI
The part at 3:20 when he checks alignment of the seat and headtubes by eyeball....super accurate and completely free. They don't need no stinking jig or new fangled alignment table!
Have fun!
#5
Randomhead
Join Date: Aug 2008
Location: Happy Valley, Pennsylvania
Posts: 24,392
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Liked 3,690 Times
in
2,513 Posts
I built a frame or two using the eyeball the ht/st alignment method. Of course, you also have to check that the DT is parallel to the sides of the BB shell or you have real problems. There was a post from someone on the framebuilders email list that said he used that method for his first 100 frames. It's really slow, and you have to be meticulous, and you still might end up with a crooked frame, so it's not for everyone. OTOH, you can easily end up with a crooked frame if you rely on your fixture too much, so there's that to consider as well.
Unfortunately, I can't use this method anymore, eyes are bad.
Unfortunately, I can't use this method anymore, eyes are bad.
#6
Senior Member
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,063
Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4197 Post(s)
Liked 3,849 Times
in
2,300 Posts
If you don't spin out when doing parking lot auto cross you don't learn... Some of the issue i have with this interweb frame discussion is the lack of allowing to make a mistake.
Aligning a bike during the build has a number of methods that all, if done well, can produce a well riding bike. As many have said before, it's how you use your tools, not which tools you own. Andy.
Aligning a bike during the build has a number of methods that all, if done well, can produce a well riding bike. As many have said before, it's how you use your tools, not which tools you own. Andy.
Thread
Thread Starter
Forum
Replies
Last Post
10speedterror
Classic & Vintage
1
09-04-11 09:03 PM