I got a Bike with Clipless Pedals but
I don't want have cleats.
I do not know where to get them ,but also my shoe size are 17s. Which might make it even harder. What should i do?? |
Get different pedals?
You need special shoes too. Not just cleats. |
Other Pedals will work on the bike?
|
Yes. All you need is a 15mm wrench. Please note, I think the left pedal screws in reverse direction (right = loose)
|
Thanks, How much are pedals these days like 10 dollars?
and do you know anything about airing up tires that need adapter? |
Here you go.
pedals http://www.nashbar.com/bikes/SubCate..._200276_200316 If you are talking about Presta valves you just unscrew the small part at the top and then screw on your Shrader adapter, connect your pump and air up the tires. When finished disconnect your pump ad unscrew your adapter. Tighten down you presta vale and put the cap back on a ride. Good luck |
Originally Posted by lechwe
(Post 11276902)
|
And, be sure if you go the Walmart (or other local store) route, you need 9/16" and not 1/2"... The 1/2" are for one piece cranks. The LBS will have some cheap pedals and will know what you need.
You may even be able to trade someone your clipless for their platform pedals... If you find someone who wants your style of clipless, whatever they are. |
Originally Posted by musicmaster
(Post 11275682)
Yes. All you need is a 15mm wrench.
http://www.parktool.com/images/produ...0218_39913.jpg Buy some used pedals from a bike shop and they'll remove your current pedals and install the ones you buy from them. The may charge you $5 for the labor (or maybe not) but the pedal wrench shown above is $25 and a cheap pedal wrench will cost at least $10. |
Do note that you'll need the cleats that specifically work with the pedals on your bike. There are many different kinds of pedal systems, and you can't use the cleat from one system with the pedal from another system.
|
Originally Posted by RonH
(Post 11278725)
Pedal wrenches are thin. Not like a 15mm wrench from the hardware store.
http://www.parktool.com/images/produ...0218_39913.jpg Buy some used pedals from a bike shop and they'll remove your current pedals and install the ones you buy from them. The may charge you $5 for the labor (or maybe not) but the pedal wrench shown above is $25 and a cheap pedal wrench will cost at least $10. |
Of course, some pedals use a fat Allen wrench in the inboard end of the spindle (many Crank Brothers, the Time RXS road pedals I have now, and some others).
OP, here's my method of removing pedals -- 1. Stand over the bike (if you have a workstand, pull the bike off and put it on the floor). 2. Level the cranks. 3. Put the wrench on the forward pedal, and position it so the free end points towards the front wheel. 4. Brace the bike's top tube against your chest, and pull up on both the wrench and the rearward pedal. 5. That's it; just be careful that you don't yank the wrench into the downtube of the frame. Since you'd pull up on both ends of the crank, you get a lot of leverage. This will help remove pedals that aren't ridiculously frozen into place. It also helps me to avoid having to remember "lefty-tighty... wait, on which side, as viewed from where?...", although I've also remembered it by thinking that the right side screws on "right", as in "correctly" (righty-tighty, lefty-loosey). |
many to choose from , get the big platform type, the molded nylon plastic ones at the bottom of the market $9 a pair
will be adequate in dry weather but get slippery when the world around you, is wet . they look like this: http://www.universalcycles.com/shopp...5&category=114 |
All times are GMT -6. The time now is 08:21 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.