Disc Break Problems
#1
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Disc Break Problems
I have a Kona Blast, i use it quite often around the city and doing so off roading, i also use it to do small drops and jumps etc. I have had it since march this year. I could feel my disc breaks (mech) were getting abit lose, so i chose to tighten them myself. They were great for the 1st day afterwards, but after doing some small lips and off road on wet grass they wernt working very well, i had to really pull on the lever to make them break and i could no longer pull skids (not that i do very often but i was just testing them). i thought that it was just because they were wet, and therefor not working to the full. But when taking the bike out the next day the breaks were the same.
I want to know what i can do about this, should i try tightening my brakes again? Or is it posible that my break pads have gone? i didnt think pad could wear away so quick and in such a short amount of time.
i am going to do some cross country and downhilling this weekend and they ned to be working properly by then.
Cheers for any help
Aidan
I want to know what i can do about this, should i try tightening my brakes again? Or is it posible that my break pads have gone? i didnt think pad could wear away so quick and in such a short amount of time.
i am going to do some cross country and downhilling this weekend and they ned to be working properly by then.
Cheers for any help
Aidan
#2
biketilldeath
Join Date: Dec 2004
Location: now residing in kamloops
Posts: 498
Bikes: 2005 Norco Aline:D
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
on the oppisite side of the calipur theres a little allen head screw tighten it untill just before the pad rubs. i prety sure thats what you problem is.
#3
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
i have tried just tightening my brakes (by pulling the cable through more). this works a little bit, but when i brake it does not stop instantly as it did before, the bike jus comes to a gradual stop.
Does this mean my pads have worn away?
Does this mean my pads have worn away?
#4
biketilldeath
Join Date: Dec 2004
Location: now residing in kamloops
Posts: 498
Bikes: 2005 Norco Aline:D
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
if you lay your bike on its side with the disk side down and look through the wheel at your brake there is a little allen head bolt tighten it a few clicks. spin the wheel, if it doesnt rub then tighten it a few more untill just before it rubs.
#8
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
so if i need new pads, do they cost a lot and will i be able to fit them my self (im not the most experienced work man but i know some stuff)
#9
Elite Rep
Join Date: Aug 2004
Location: Melbourne - Australia
Posts: 2,096
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
How about try and clean the rotors first if you havn't already. Use denatured alchol (metho spirits) and give them a good clean. If braking still sucks then your pads are most likely the problem. Pads, depending on quality, depend on price obviously. I'd say you would be able to fit them yourself, just gotta be carefull removing/installing. Take the wheel off, un-tension the brake, and there should be a pin thing you un-bend or slide-out that will allow you to release the pad. This might change depending on brake models, not really sure.
But just make sure that everything is tight and the pads are well cleaned before going out and buying new pads.
But just make sure that everything is tight and the pads are well cleaned before going out and buying new pads.
Last edited by blue_neon; 09-13-05 at 05:00 AM.
#11
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
guy at the shop told me that the pads were prob contaminated, so i bought some new pads and will try to fit them tonight... can anybody give me any suggestions to help me stop these new pads from becoming contaminated.
#12
Senior Member
Join Date: Feb 2005
Location: Spain, although I'm Hungarian
Posts: 1,855
Bikes: Check signature
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
guy at the shop told me that the pads were prob contaminated, so i bought some new pads and will try to fit them tonight... can anybody give me any suggestions to help me stop these new pads from becoming contaminated.
#13
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
ahhhh, that could be it... ive got a vfeeling my friend sprayed some WD40 on the breaks just before they started not working, could this of contaminated them
#14
Just Ride
Join Date: Sep 2004
Location: Melbourne - Australia
Posts: 1,343
Bikes: 2005 Giant Yukon with the works.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
More likely. Like what Drunken Chicken said, any type of oil that gets on the rotors or pads make the worst sound ever. In other words you would need to get new pads. Just always remember to rub Dentured Alochol (Methylated Spirits) on your rotors. Works well
#16
Senior Member
Join Date: Feb 2005
Location: Spain, although I'm Hungarian
Posts: 1,855
Bikes: Check signature
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
it also says on the the brake pad packaging that there will be a burn in period - how long will this be?
#17
I drink your MILKSHAKE
Join Date: Jul 2002
Location: St. Petersburg, FL
Posts: 15,061
Bikes: 2003 Specialized Rockhopper FSR Comp, 1999 Specialized Hardrock Comp FS, 1971 Schwinn Varsity
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Originally Posted by gingerbread
ahhhh, that could be it... ive got a vfeeling my friend sprayed some WD40 on the breaks just before they started not working, could this of contaminated them
#18
Senior Member
Join Date: May 2004
Posts: 1,398
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
so if i need new pads, do they cost a lot and will i be able to fit them my self (im not the most experienced work man but i know some stuff)
Otherwise, I would suggest that you sumberse your pads in denatured alcohol overnight. Clean them with a paper towel. Re-install them. They should be better at first but not "great" until you wear them in once again.
The alternative is to buy a blow torch and simply burn the contaminats off. But this will leave a glaze on the pad surfaces which you'll have to sand off.
Finally, keep any SPRAY LUBES well away from your discs and rotors. No more spray lubing for you. That crap really doesn't work well anyway.
AFTER you ride, put the chain through a cleaner an THAN LUBE. Use drops and put a single one on each chain roller. Let it settle overnight. This will keep the lube for splattering onto your breaking surfaces.
#19
Senior Member
Join Date: May 2004
Posts: 1,398
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
guy at the shop told me that the pads were prob contaminated, so i bought some new pads and will try to fit them tonight... can anybody give me any suggestions to help me stop these new pads from becoming contaminated.
#20
Senior Member
Join Date: May 2004
Posts: 1,398
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
it also says on the the brake pad packaging that there will be a burn in period - how long will this be?
#21
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
so ive cleaned the disc and rotors and installed the new pads, i did the front wheel 1st... when i put the wheel back on i could not have the brakes as tight as i liked them because they were rubbing against the disc. is there anywhere other than the cable you pull through and the allen key slot on the back of the caliper that i can loosen the pads so that i can tighten the lever.
when i put the rear wheel on, after installing new pads, the same problem occured again but much worst. i have totaly losened the allen key slot on the back and let the cable go very lose, but the disc still rubs also as the cable is so loose when i pul the lever the break does not react. Therefore is there somewhere i can losen the pads to stop them rubbing.
there are 2 other allen key slots near the one i losened on the back of the caliper, do these losen the pads
sorry if this is hard to understand but i found it difficult to explain
cheers for any help
when i put the rear wheel on, after installing new pads, the same problem occured again but much worst. i have totaly losened the allen key slot on the back and let the cable go very lose, but the disc still rubs also as the cable is so loose when i pul the lever the break does not react. Therefore is there somewhere i can losen the pads to stop them rubbing.
there are 2 other allen key slots near the one i losened on the back of the caliper, do these losen the pads
sorry if this is hard to understand but i found it difficult to explain
cheers for any help
#22
Elite Rep
Join Date: Aug 2004
Location: Melbourne - Australia
Posts: 2,096
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by gingerbread
so ive cleaned the disc and rotors and installed the new pads, i did the front wheel 1st... when i put the wheel back on i could not have the brakes as tight as i liked them because they were rubbing against the disc. is there anywhere other than the cable you pull through and the allen key slot on the back of the caliper that i can loosen the pads so that i can tighten the lever.
when i put the rear wheel on, after installing new pads, the same problem occured again but much worst. i have totaly losened the allen key slot on the back and let the cable go very lose, but the disc still rubs also as the cable is so loose when i pul the lever the break does not react. Therefore is there somewhere i can losen the pads to stop them rubbing.
there are 2 other allen key slots near the one i losened on the back of the caliper, do these losen the pads
sorry if this is hard to understand but i found it difficult to explain
cheers for any help
when i put the rear wheel on, after installing new pads, the same problem occured again but much worst. i have totaly losened the allen key slot on the back and let the cable go very lose, but the disc still rubs also as the cable is so loose when i pul the lever the break does not react. Therefore is there somewhere i can losen the pads to stop them rubbing.
there are 2 other allen key slots near the one i losened on the back of the caliper, do these losen the pads
sorry if this is hard to understand but i found it difficult to explain
cheers for any help
1. Depending on your brakes you CANNOT adjust the 'toe' of the pads unlike normal 'v-brakes'. Although you CAN tighten the cable tension at the brake levers if you dont want to use the allen key hole. Where the rubber housing comes out of the lever there will be a notch. Screw it out, you will tension the cable, tightening the brake (screwing it back in will loosen it back).
2. V-Brakes are a lot better to adjust, you have 3 options and you can get a perfect non-rubbing wheel with perfect tension, thats what I LOVE about them. Lower end disk brakes dont have the 'toe' features (like V's) to my knowlegde that can move the location of the pads. You really only have one adjustment, and that is the cable tension. Although I must add different models of disks have different features so you might be able to adjust the positioning of the pads but that would depend on brake model, so i couldn't really help you there.
#24
MudLover
Join Date: Nov 2004
Location: Melbourne, Australia
Posts: 56
Bikes: Giant AC 2005, Custom BMX(no 2 parts from same brand) and no-name (but reliable) duallie
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
on the subject of 'toe' ing, ive noticed that my rotor is at a bit of an angle to the pads and cant seem to fix it. Whats up with that?
#25
Beginner Expert
Thread Starter
Join Date: Jun 2005
Posts: 115
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
so back from the bike shop, the guy says: i have to take the wheel off, put a small screwdriver between the pads to open them out a little bit, as they sometimes stick together when installing them...
has anybody else had this problem, and does it sound like a reasonable explanation
has anybody else had this problem, and does it sound like a reasonable explanation