Cycling and bicycle discussion forums. 
   Click here to join our community Log in to access your Control Panel  


Go Back   > >

Recreational Cyclocross and Gravelbiking This has to be the most physically intense sport ever invented. It's high speed bicycle racing on a short off road course or riding the off pavement rides on gravel like :The Dirty Kanza". We also have a dedicated Racing forum for the Cyclocross Hard Core Racers.

User Tag List

Reply
 
Thread Tools Search this Thread
Old 11-30-05, 02:18 PM   #1
IchbinJay
Senior Member
Thread Starter
 
IchbinJay's Avatar
 
Join Date: Oct 2004
Location: Massachusetts
Bikes: Jamis Ventura Comp (2010) and Raleigh M80 (1998).
Posts: 446
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Canti Bosses...

Are there any bosses that can be fastened to a brakeless frame without brazing or welding of any kind?
IchbinJay is offline   Reply With Quote
Old 12-02-05, 01:22 PM   #2
ZenNMotion
Senior Member
 
Join Date: Dec 2003
Location: Inside the beltway
Bikes:
Posts: 236
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
I've never seen any, and if I did, I wouldn't trust them. But I'm guessing that your real question is, how can I use this old road bike frame for cross? If you have an older frame, set up for "normal reach" caliper brakes, you can use old-school centerpull brakes- these have lots of clearance for cross tires and plenty of stopping power. I have an old steel Schwinn commuter with Weinmann "Vaincoeur" centerpulls that I rescued off the neighbor's curb on garbage day that I can mount Michelin Muds (aggressive knobbys that measure 35mm) without a problem. I can also fit fenders in there as well- just barely with the muds, but easily with slightly lower profile 30c CX tires. Go find a bike shop that keeps old parts and I'm sure they will have a set of old weinmann's or universal's lying around- nobody specs or uses these anymore and it's too bad because they're still really good brakes, even if they're not pretty... But then, objectively, cantilevers with all the exposed cables are pretty odd looking also, especially on a high end CX frame with shaped tubing. Anyway, ask your LBS, buy a junker at Goodwill, check Ebay, or even pay a visit to the dump, it shouldn't be too hard to find some centerpulls. These may not work, however if you are trying to convert a road racing frame that uses short-reach caliper brakes as you may not be able to set the brake pads high enough to contact the rim properly, so you need to check that. But if not, just get an old frame that does- something like an old 70s-80's steel Raleigh Gran Prix or old Nishiki with centerpulls would make a perfectly useable cyclocross bike with lots of tire clearance. Those old roadies handle pretty nice on a cross course, too (I've done it with the Schwinn, it's fun!), although it might be a little heavy lifting over the barriers, it really wouldn't slow you down much over an expensive cross bike, especially in the C/B races your first couple of seasons. Spraypaint it neon pink, single ring with 1 bar-con shifter on a 6 speed freewheel and I guarantee you'd have more admirers than that Poser with the Carbon Ridley...

If you mean a brakeless bike, as in a track bike, then its something different. A real track fork does not have a drilled hole in the crown for a brake. And it's probably not possible or safe to drill it yourself. If you don't mind burning some paint, a frame builder could brake on canti bosses, shouldnt be too expensive. I've seen quotes for about 40 bucks per wheel. But if its a track frame you only need front cantis anyway for fixed gear riding, so just pick up a cheap used CX or hybrid fork and be done with it.

Last edited by ZenNMotion; 12-02-05 at 01:39 PM.
ZenNMotion is offline   Reply With Quote
Old 12-02-05, 01:49 PM   #3
ApolloCVermouth
Senior Member
 
ApolloCVermouth's Avatar
 
Join Date: Jul 2005
Location: Toronto
Bikes: homemade cyclocross, 2005 KHS Flite 100 frame + assorted parts
Posts: 140
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
This was just discussed in the Bike Mechanics forum.

Canti Bosses

If you find a frame you like it might be worth it to have bosses brazed on. I got two sets done on an old Nishiki for 75$ cdn. If you try to do this on a more modern road frame you might find the clearance to narrow in the seat stays.
ApolloCVermouth is offline   Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -6. The time now is 01:54 PM.