Go Back  Bike Forums > Bike Forums > Road Cycling
Reload this Page >

Fixing a Bent Wheel

Notices
Road Cycling “It is by riding a bicycle that you learn the contours of a country best, since you have to sweat up the hills and coast down them. Thus you remember them as they actually are, while in a motor car only a high hill impresses you, and you have no such accurate remembrance of country you have driven through as you gain by riding a bicycle.” -- Ernest Hemingway

Fixing a Bent Wheel

Old 11-07-04, 07:33 PM
  #1  
silly rabbit...
Thread Starter
 
pk273340's Avatar
 
Join Date: Aug 2004
Location: CT and Philly
Posts: 119

Bikes: 2006 CAAD 8 with si cranks and campy Veloce

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Fixing a Bent Wheel

the rear wheel of my trek 1000 is out of true.
When i spin it it spins free for about a half a revolution and then rubs against the left brake pad. i know this is bad but can it be repaired and for how much, or do i need a whole new wheel.
my bike is a 2001 trek 1000, with the stock vuelta airline 2 wheels.
pk273340 is offline  
Old 11-07-04, 07:56 PM
  #2  
World Champion, 1899
 
Maj.Taylor's Avatar
 
Join Date: Sep 2004
Location: Bush-Whacked, U.S.A.
Posts: 623

Bikes: Litespeed Vortex

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
If it's only truing, it's no big deal. Quite frankly, I think bike shops charge too much for the typical truing. If I'm not mistaken, they may charge $20-$25. I really don't know b/c I've trued my own wheels for at least 15 years now.

And that's what you should be looking to do. Truing a wheel is very easy. Take it to the bike shop a couple of times and have them let you watch. Then go out and read up on how to true a wheel. With not very much practice at all, you'll be keeping your own wheels true in no time.

All that said, make sure you know the difference between an out-of-true wheel and an out-of-round wheel. The former can almost always be put right. The latter usually requires a new wheel or a rebuild. (Out-of-true applies to the wheel's lateral plane. Our-of-round applies to the wheel's vertical plane. The former rubs against your pads. The latter goes bump, bump, bump as you ride.)
Maj.Taylor is offline  
Old 11-07-04, 07:58 PM
  #3  
la vache fantôme
 
phantomcow2's Avatar
 
Join Date: Aug 2004
Location: NH
Posts: 6,266
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 1 Time in 1 Post
well my lbs trues wheels regardless of condition for a flat fee of 15$. I dont think yours will be overly different. It doesnt sound like a huge issue, infact if it isnt that much out of true you can probably true it yourself if you know how. Though ideally you should have a stand, i picked up a park TS-7 for 64.99 shipped
phantomcow2 is offline  
Old 11-07-04, 08:05 PM
  #4  
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1572 Post(s)
Liked 642 Times in 363 Posts
It depends a little bit on how badly it's warped but, most likely, that much out-of-trueness can be adjusted away. A bike shop will most likely charge you between $10.00 and $25.00 to do the job. Depending on what they actually do, $25.00 may be a bargain and $10.00 might be a rip-off.

The right way to do it is to check each spoke with a tensiometer to make sure the spoke tension is equal on every one, then true the wheel by tightening and loosening opposing pairs of spokes until the wheel is both round and straight from side to side. That would be the $25.00 version.

The quick, dirty way is to find where the rim rubs the brake pad, and tighten the spokes on the opposite side until the wheel looks straight. If you want to try doing this yourself, take your wheel into an LBS to make sure that you get the right sized spoke wrench. Spoke wrench sizes aren't very different, but too small won't fit at all and too big will round off the wheel's nipples.
Retro Grouch is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.