Advertise on Bikeforums.net



Search:

Type: Posts; User: FastJake; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.91 seconds.

  1. Replies
    10
    Views
    285

    Small cracks in the tread/sidewall are harmless....

    Small cracks in the tread/sidewall are harmless. As mentioned above, pay attention to how you're storing them.
  2. Replies
    12
    Views
    299

    Put the Velox tape back in, you might have to buy...

    Put the Velox tape back in, you might have to buy a different width. It sounds like the stuff you had before was too narrow.

    Electrical or duct tape is not strong enough to withstand the force of...
  3. This. Screw it back in and simply wiggle it with...

    This. Screw it back in and simply wiggle it with your hand. You don't need penetrating oil, it's not corroded in place. You mechanically force-fit it into place. Now you need to reverse that. Use a...
  4. Replies
    15
    Views
    719

    I just dealt with a too-big post in a frame...

    I just dealt with a too-big post in a frame recently. I didn't know what to do. I could turn it but I couldn't move it vertically to save my life. It was one of the old SR aluminum posts with the...
  5. Watch that ratio. Are you sure you want 53/49?...

    Watch that ratio. Are you sure you want 53/49? You'll need a giant cassette, or live somewhere with no hills whatsoever. Or it was a typo...
  6. How bunged up are the dropouts? Tug-nuts and...

    How bunged up are the dropouts?

    Tug-nuts and similar products are unnecessary band-aids in a properly functioning rear wheel. I've run plenty of fixed gears with quick release rears and horizontal...
  7. So did you actually wear out your current DA7700...

    So did you actually wear out your current DA7700 rings? If so I'd change your chain/cassette more frequently. Or you just ride a LOT. At the cost of those NOS DA7700 rings I'd just get a lightly used...
  8. Replies
    16
    Views
    446

    In some cases I consider shims a kludge but when...

    In some cases I consider shims a kludge but when using a 1 1/8" stem on a 1" steerer tube it works so well you'll never know the difference. Unless you have a good eye and can tell that the stem is a...
  9. Replies
    16
    Views
    414

    Hard to tell from the picture but that looks ok....

    Hard to tell from the picture but that looks ok. How does it spin in the stand? How does it ride? That's what I'd be concerned with. Structurally, regarding the material lost, it looks fine. Those...
  10. Replies
    9
    Views
    513

    +1 OP is doing it wrong or just being too picky....

    +1 OP is doing it wrong or just being too picky. It's really not critical.

    Whenever possible I use tubes that are a bit oversized. Sure they might be a bit heavier but I don't have to fill them as...
  11. Replies
    24
    Views
    845

    I got a stash of really good hose clamps when I...

    I got a stash of really good hose clamps when I was working at a place that made washing machines. I'm currently using them to hold two normal bottle cages on frames with only one set of bosses. Too...
  12. Thanks for the tip. I'm going to use the same...

    Thanks for the tip. I'm going to use the same 2.0/1.6/2.0 spokes I always get from Yellow Jersey. I am a bit worried because they're pretty light rims and I hear they're "finicky" to build up. Mostly...
  13. Edit because I didn't answer the OP's question......

    Edit because I didn't answer the OP's question... (sorry.) Those Mavic Mach 2 rims will be just fine for cross. Perfect choice.



    Exactly. I don't know why light tubular rims aren't available...
  14. Replies
    35
    Views
    833

    Looking at the pictures you posted I can imagine...

    Looking at the pictures you posted I can imagine what those brakes feel like in their current state. You should definitely get new cables and housing, read up on proper cable routing here: Cables
    ...
  15. Replies
    3
    Views
    227

    +1 Just get a decent surface to apply the new...

    +1 Just get a decent surface to apply the new glue. It's really not possible to remove the old glue from a tire as it gets so soaked into the base tape. And there's no reason to remove it.
  16. Replies
    47
    Views
    1,003

    I run Schraeders whenever I can but that still...

    I run Schraeders whenever I can but that still leaves me with the majority of my valves Presta. I have so many rims that are too deep or too narrow such that I can't or don't want to drill them out...
  17. Replies
    47
    Views
    1,003

    This is why I don't use it. I bought a bike with...

    This is why I don't use it. I bought a bike with Slimed tubes (Presta valves.) I eventually had to throw away both tubes because I literally could not get air in or out of the tubes anymore.

    I'd...
  18. Replies
    21
    Views
    437

    It makes sense in theory but I think your biggest...

    It makes sense in theory but I think your biggest problem will be finding an appropriate hub.

    If you want even tension between sides you can use an OCR rim or different gauge spokes on each side,...
  19. I agree with oddjob on the sizing. I think...

    I agree with oddjob on the sizing.

    I think $200 is a reasonable price, it's a nice frame with nice XT components. But that fork looks like a modern and really cheap (basically junk, super heavy)...
  20. Thread: Carbon Wheels

    by FastJake
    Replies
    7
    Views
    420

    +1 If the wheels are "full carbon" then by...

    +1

    If the wheels are "full carbon" then by definition they don't have an aluminum brake track. From what I understand (but I could be wrong) before manufacturers figured out how to make full...
  21. Replies
    14
    Views
    719

    I do not recommend exceeding the maximum pressure...

    I do not recommend exceeding the maximum pressure listed on the sidewall. Tire blowout/rim failure is a possibility. If you're needing to put that much air in your tire you should get a wider tire...
  22. Replies
    12
    Views
    487

    Sounds like it's a Shimano compatible hub not an...

    Sounds like it's a Shimano compatible hub not an actual Shimano hub. Probably a cheap one (that's why it's breaking.) If you can even find parts for this they will eventually fail too. I've never had...
  23. I never do, I think it would mostly attract dirt....

    I never do, I think it would mostly attract dirt. But it won't hurt anything either.

    Your real problem with an aluminum Shimano/SRAM splined freehub body is that aluminum is too soft for this...
  24. I think you're right. I think Ultra Shift is the...

    I think you're right. I think Ultra Shift is the good one. Escape is definitely ​the bad one.
  25. I didn't know there was a difference. I think all...

    I didn't know there was a difference. I think all the Campy left shifters are the same.

    You just don't want anything with the "Escape" mechanism they made for a few years. You want the "Power...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4