Advertise on Bikeforums.net



Search:

Type: Posts; User: bikeman715; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.21 seconds.

  1. You very welcome .Yes they do have a lot of...

    You very welcome .Yes they do have a lot of freewheel tools . And a couple cassette removing tools . The one I refer you to in my other post is the one for Shimano 's cassettes . As with the BB tool...
  2. For the bottom bracket most likely you'll need...

    For the bottom bracket most likely you'll need this tool , Park Tool Co. BBT-22 : Bottom Bracket Tool : Bottom Bracket , and for your cassette this one Park Tool Co. FR-5 : Cassette Lockring Tool...
  3. Replies
    5
    Views
    213

    I agree , I wasn't sure because it is a dura-age...

    I agree , I wasn't sure because it is a dura-age cassette and if the spacing would be the same . Thank bill for the correction .
    A mid size cage would work too if wanted .
  4. Replies
    5
    Views
    213

    "The crankset is what I believe is the original...

    "The crankset is what I believe is the original stock...I'm assuming it is Shimano exage trail 28 x 38 x 48 biospace 175mm (by the way, what does this all mean?? can someone break it down for me?) "...
  5. Yes I remember them too .

    Yes I remember them too .
  6. Thread: Best Tools

    by bikeman715
    Replies
    38
    Views
    1,650

    +1

    +1
  7. Replies
    32
    Views
    883

    I have broken both Pedro's and Park's levers in...

    I have broken both Pedro's and Park's levers in my day .
  8. The Bicycling Guide to Complete Bicycle...

    The Bicycling Guide to Complete Bicycle Maintenance & Repair for Road & Mountain Bikes is a good one to start with .
  9. Replies
    23
    Views
    741

    If it was brake rubbing you would see more wear...

    If it was brake rubbing you would see more wear on the side wall of the tire going around the rim .
  10. Replies
    14
    Views
    396

    Vise Grips will help in removing the nipple but...

    Vise Grips will help in removing the nipple but the nipple will be destroy in doing so . Any nipple and/or spoke for that matter should be replace if you can't get the nipple to turn .
  11. Thread: Oh, BALLS!!

    by bikeman715
    Replies
    37
    Views
    984

    This is where I get my . Bike Tools Etc. - 1000's...

    This is where I get my . Bike Tools Etc. - 1000's of bicycle tools and parts for the home mechanic!= . As far as storing them , just keep them in the container they come in . I never have any rust...
  12. These would be the right tool(s) for the job ....

    These would be the right tool(s) for the job . Bike Tools Etc. - 1000's of bicycle tools and parts for the home mechanic! .
  13. Thread: Tire sizes

    by bikeman715
    Replies
    5
    Views
    375

    only if they clear the chainstay and the seatstay...

    only if they clear the chainstay and the seatstay .
  14. Replies
    17
    Views
    385

    Make sure the locknut and cone is lock together...

    Make sure the locknut and cone is lock together on the side you didn't remove from the axle . If you don't you never get you adjustment right .
  15. Replies
    9
    Views
    340

    If you remove the shifter ,there is a bolt you...

    If you remove the shifter ,there is a bolt you can tighten by turning it counter clock wise which will keep it tight .
  16. It is possible for it to happen . Or other...

    It is possible for it to happen . Or other things happen you hit the doorway on the way out and not notice it or a bike rack or the bike got put down on the drive side ,anything is possible . It...
  17. use 90 % or better rubbing alcohol on the rims to...

    use 90 % or better rubbing alcohol on the rims to remove the pads buildup .
  18. Your rear derailleur hanger is bent . It need to...

    Your rear derailleur hanger is bent . It need to be replace or adjust by your LBS . Park Tool Co. ParkTool Blog Rear Derailleur Hanger Alignment , this might help .
  19. It depend on the rim if you can drill it or not ,...

    It depend on the rim if you can drill it or not , with most yes and others no . How much room between the walls does the rim have ? The adapters work fine if that what you want to use . the patch...
  20. Try a auto parts store , they too have springs of...

    Try a auto parts store , they too have springs of different sizes .
  21. +1 that what I would do and see if the rim is...

    +1 that what I would do and see if the rim is bent or not .
  22. Try putting the Right (R) pedal in thou the back...

    Try putting the Right (R) pedal in thou the back side of the crank arm and see if that will clean the treads or if you have a tap of the right size and treads to do the same . Use oil when you do ....
  23. Replies
    19
    Views
    608

    yep , it sure does . LOL

    yep , it sure does . LOL
  24. Replies
    13
    Views
    481

    It should be done every year during a tune-up or...

    It should be done every year during a tune-up or overhaul .
  25. Replies
    10
    Views
    252

    what you are looking for is a gap between the...

    what you are looking for is a gap between the chain rings so the chain can move between them . you can try the thicker ones on the granny and see how it work out .
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4