Advertise on Bikeforums.net



Search:

Type: Posts; User: bikeman715; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.41 seconds.

  1. Replies
    38
    Views
    422

    +1 it what on my bike .

    +1 it what on my bike .
  2. ok , it was just a thought . have you try the 12...

    ok , it was just a thought . have you try the 12 -1 bearings and see how that work out ?
    meaning you put 11 balls in each cup instead of 12 .
  3. sometime the cups (pedal ' s body ) is different...

    sometime the cups (pedal ' s body ) is different in size from front to back . so maybe 10 bearings in one cup (side) and 14 in the other .
  4. Replies
    9
    Views
    274

    It would be best if you took your bike to a shop...

    It would be best if you took your bike to a shop or co-op and let them handle it . Also it would help us here if you show some pictures so we can help you better .
  5. Yes , I have seen it a few time . Shimano thought...

    Yes , I have seen it a few time . Shimano thought was you didn't need to adjust or remove that cone ,without replace the axle . All adjustment is done on the non drive side .
  6. Replies
    5
    Views
    226

    To toe in your brakes , use anything from your...

    To toe in your brakes , use anything from your business card to a rubber band on the rear of the brake pads . squeeze the brake lever ( or tie the brake lever to the handlebars ) as you tighten the...
  7. "With no 16 cog which makes it completely...

    "With no 16 cog which makes it completely unsuitable for road riding." I agree with you Drew , but I was just answering the OP question about does a cassette exist with a lower gear compare to the...
  8. I found this one on ebay , 12-30 Cassette | eBay...

    I found this one on ebay , 12-30 Cassette | eBay
  9. If it new then I would return the wheel (hub) to...

    If it new then I would return the wheel (hub) to the seller for a replacement .
  10. Replies
    16
    Views
    372

    There should be a oil port in the center of the...

    There should be a oil port in the center of the hub where you add the oil , there no need to take the hub apart unless something is broken , if there is parts are easy to get . The clip is where you...
  11. Are you saying the treads on the hub are stripped...

    Are you saying the treads on the hub are stripped ? if so try using a tread file on them to reshape them . The treads on the freewheel are harden steel so it very unlikely they are , where the hub is...
  12. Replies
    23
    Views
    1,197

    Back in the early 80's Cannondale did the same to...

    Back in the early 80's Cannondale did the same to one of their touring model I remember right it was the T1000 .
  13. I agree with alcjphil , your front derailleur is...

    I agree with alcjphil , your front derailleur is too high , lower it alittle more and you do need to adjust the high screw on it also so the chain doesn't jump the chainring .
  14. You very welcome .Yes they do have a lot of...

    You very welcome .Yes they do have a lot of freewheel tools . And a couple cassette removing tools . The one I refer you to in my other post is the one for Shimano 's cassettes . As with the BB tool...
  15. For the bottom bracket most likely you'll need...

    For the bottom bracket most likely you'll need this tool , Park Tool Co. BBT-22 : Bottom Bracket Tool : Bottom Bracket , and for your cassette this one Park Tool Co. FR-5 : Cassette Lockring Tool...
  16. Replies
    5
    Views
    233

    I agree , I wasn't sure because it is a dura-age...

    I agree , I wasn't sure because it is a dura-age cassette and if the spacing would be the same . Thank bill for the correction .
    A mid size cage would work too if wanted .
  17. Replies
    5
    Views
    233

    "The crankset is what I believe is the original...

    "The crankset is what I believe is the original stock...I'm assuming it is Shimano exage trail 28 x 38 x 48 biospace 175mm (by the way, what does this all mean?? can someone break it down for me?) "...
  18. Yes I remember them too .

    Yes I remember them too .
  19. Thread: Best Tools

    by bikeman715
    Replies
    38
    Views
    1,726

    +1

    +1
  20. Replies
    32
    Views
    1,047

    I have broken both Pedro's and Park's levers in...

    I have broken both Pedro's and Park's levers in my day .
  21. The Bicycling Guide to Complete Bicycle...

    The Bicycling Guide to Complete Bicycle Maintenance & Repair for Road & Mountain Bikes is a good one to start with .
  22. Replies
    23
    Views
    784

    If it was brake rubbing you would see more wear...

    If it was brake rubbing you would see more wear on the side wall of the tire going around the rim .
  23. Replies
    14
    Views
    423

    Vise Grips will help in removing the nipple but...

    Vise Grips will help in removing the nipple but the nipple will be destroy in doing so . Any nipple and/or spoke for that matter should be replace if you can't get the nipple to turn .
  24. Thread: Oh, BALLS!!

    by bikeman715
    Replies
    37
    Views
    1,010

    This is where I get my . Bike Tools Etc. - 1000's...

    This is where I get my . Bike Tools Etc. - 1000's of bicycle tools and parts for the home mechanic!= . As far as storing them , just keep them in the container they come in . I never have any rust...
  25. These would be the right tool(s) for the job ....

    These would be the right tool(s) for the job . Bike Tools Etc. - 1000's of bicycle tools and parts for the home mechanic! .
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4