Advertise on Bikeforums.net



Search:

Type: Posts; User: bikeman715; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.85 seconds.

  1. CM-5.2 and CM-5 Rebuild Kit | Park Tool...

    CM-5.2 and CM-5 Rebuild Kit | Park Tool & Lubes , you can find this at different shops and online like at amazon.com...
  2. Replies
    4
    Views
    231

    Try punching the bearings out , In doing so it...

    Try punching the bearings out , In doing so it should give you access to the pawls , then you can clean and lube them . If you don't want to do that , then remove the seal clean and lube the bearing...
  3. Replies
    24
    Views
    529

    Some bike just have a dead feeling to them , they...

    Some bike just have a dead feeling to them , they just don't roll well down the road , other bike have a lively feel to them and they roll with very little effort . You can try different wheels and...
  4. Replies
    5
    Views
    189

    have you try it on a bike ? is there still play...

    have you try it on a bike ? is there still play when you use (close ) the QR ? I would back off the adjustment and see if the play goes away when you mount the wheel into the frame .
  5. Replies
    6
    Views
    247

    If you bent the bracket the guard is mounted to...

    If you bent the bracket the guard is mounted to back a little then you should get the clearance you looking for . I t wouldn't take much to do so .
  6. Replies
    1
    Views
    170

    the chains for 5,6,7 speeds will work just find...

    the chains for 5,6,7 speeds will work just find for you .
  7. Replies
    12
    Views
    574

    sorry you are hurt , hope you heal soon . as far...

    sorry you are hurt , hope you heal soon . as far the bike goes replace any broken parts . don't worry about what happen , just get better and start riding soon .
  8. if there are spacer(s) behind the cassette , yes...

    if there are spacer(s) behind the cassette , yes you can remove them and add a 8 spds cassette . doing so shouldn't mess up your chainline .
  9. Replies
    9
    Views
    406

    the rear brake cable should have more of curve to...

    the rear brake cable should have more of curve to it as it come from the holder to the stop on the brake calipers . it ok for it goes above the seatstay as you do this . other than that the rest look...
  10. Replies
    8
    Views
    247

    is the spring in both holes , one on the frame...

    is the spring in both holes , one on the frame and inside the arm ?
  11. Replies
    8
    Views
    247

    check the post for any burrs and if so file it...

    check the post for any burrs and if so file it down . maybe the bolt was too tight and mushroom the post , then again file down or replace the post . check the pad make sure it doesn't have a lip if...
  12. Replies
    3
    Views
    197

    Replacement parts are hard to come by . Have you...

    Replacement parts are hard to come by . Have you try overhauling the caliper ? or put some grease on the spring itself ? Or maybe the hardware is too tight ? If so try backing it of by 1/8 -1/4 turn...
  13. Replies
    16
    Views
    655

    +1

    +1
  14. Replies
    6
    Views
    280

    Yes indexing does work with Biopace 's rings . ...

    Yes indexing does work with Biopace 's rings . You can replace the rings as long the bolt holes line up .
  15. Replies
    37
    Views
    885

    it not wise to do so . you don't know their...

    it not wise to do so . you don't know their history .
  16. Check the tighten of the derailleur's mounting...

    Check the tighten of the derailleur's mounting bolt , if it to tight then the derailleur will hang up and not rotate as it should . Back it off about a 1/4 turn and see if that improve anything .
  17. I would start with a longer loop of housing ....

    I would start with a longer loop of housing . there should be no bents or kinks in the housing from the stop to the derailleur , just a nice smooth curve . A lot of mechanics make them too short...
  18. Some of us were trained this way in the shop by...

    Some of us were trained this way in the shop by other mechanics .
  19. You can use a treaded rod and nuts and washers ....

    You can use a treaded rod and nuts and washers . Put the rod into the dropouts and tighten the nut on the side that next to be move in . Measure the distant until it where you want it . Remove the...
  20. Replies
    12
    Views
    456

    if the hubs and rims are in good shape , I can...

    if the hubs and rims are in good shape , I can not see why any shop would refuse the work . I am in California , I can do the work . It a manor of cost of shipment and time to do it .Most shop...
  21. Replies
    9
    Views
    318

    I agree about the chain being too short .

    I agree about the chain being too short .
  22. Replies
    6
    Views
    306

    they should be flush with the nipple head . when...

    they should be flush with the nipple head . when they not there a better chance of them poking thou and hitting the tube .
  23. For the record , Shmanio did and does low end...

    For the record , Shmanio did and does low end seal bottom bracket , They the LP series, some were also the LN series and yes the plastic cup goes into the drive side , which is left handed thread ....
  24. Replies
    20
    Views
    536

    When you get your new wheel you or a shop need to...

    When you get your new wheel you or a shop need to overhaul the hub , replace the grease in there and adjust the cones and true the wheel .
  25. Replies
    7
    Views
    307

    keep it out of the sun and away from and motors...

    keep it out of the sun and away from and motors such as a washing machine , and such .
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4