Advertise on Bikeforums.net



Search:

Type: Posts; User: edotomato; Keyword(s):

Page 1 of 4 1 2 3 4

Search: Search took 0.17 seconds.

  1. Replies
    16
    Views
    433

    Awesome! I love a good project.

    Awesome! I love a good project.
  2. Replies
    16
    Views
    433

    Are you pulling my leg, or would this really...

    Are you pulling my leg, or would this really work!? Surely it's more complicated.
  3. Replies
    16
    Views
    433

    Rollers! (Kreitler or Elite mag)

    Hi guys, I'm looking to buy some rollers, because as much as I wish I could "Man up!", "Bite the bullet!", "Suck it up" and ride outside- it's just too cold!

    So, to try and keep my hard-earned...
  4. Thank you! Exactly the information I was looking...

    Thank you! Exactly the information I was looking for.
  5. Chainring compatibility with different width chains

    I've got a bike with a 7-speed chainring that I'm looking to replace the drivetrain on, upgrading to either 10- or 11-speed. If I use 10-speed, will I have to use a 10-speed specific chainring, or...
  6. Replies
    6
    Views
    174

    The clicking is when I rotate the hub shell and...

    The clicking is when I rotate the hub shell and freehub body together- and sounds similar, but quiter, to the rattling. A similar pitch and timbre.
  7. Replies
    6
    Views
    174

    To restate: The entire hub is still intact; free...

    To restate: The entire hub is still intact; free hub, axle, hub shell. When I spin the hub around the axle it makes this noise.
  8. Replies
    6
    Views
    174

    Rear hub rattle

    I have a Shimano Exage rear hub- freehub style for a 7speed cassette. Detached from the wheel, when I spin it around the axle it makes a clicking noise. Then when I shake it, it makes a similar...
  9. Replies
    0
    Views
    57

    Open BB headset mix and matching.

    I replaced the top part of my open ball-bearing headset, but left the bottom (crown race, bearings, and cup) to retain enough stack height. The ball bearing tracks seemed to be at different angles as...
  10. Replies
    23
    Views
    355

    No, it works as usual- the band with the Sante...

    No, it works as usual- the band with the Sante logo and the pearl coloured dome above it slide off and give access to flats, so usual wrenches fit.

    I am planning on replacing it with a...
  11. Replies
    23
    Views
    355

    Trust me, I have searched the Vancouver area for...

    Trust me, I have searched the Vancouver area for a thin 32mm wrench that fill fit my specific cup- there being a very close clearance. I don't have the tools, I have access to them.



    Thanks,...
  12. Replies
    23
    Views
    355

    I've tried everything suggested- washers, two...

    I've tried everything suggested- washers, two wrenches, locktite- and the problem persists. (I jest- I haven't used locktite.)

    I think PianoFuji has identified the cause of the issue- and I will...
  13. Replies
    23
    Views
    355

    Just to be clear: I had tried using two wrenches....

    Just to be clear: I had tried using two wrenches. And really, I mean really cranking down on it. But it still loosens.

    A problem is that the flats on the adjustable race are about 2mm wide when...
  14. Replies
    23
    Views
    355

    This is what I meant by I'd be tightening it...

    This is what I meant by I'd be tightening it against itself. It still loosens off after doing this, to the point where I could unscrew it by hand, with ease. Another problem is that the wrench...
  15. Replies
    23
    Views
    355

    Oh headset woes..

    I currently have a 25 year old Shimano Sante headset (ultegra level-ish) on my bike, but it loosens very quickly no matter what I try. There is a grooved, keyed washer that fits and locks onto the...
  16. Replies
    17
    Views
    481

    Endlessly dirty chain

    I kept wiping my chain down with a rag then relubing, maybe once a week. But every time I relube, I wipe off the excess and very quickly (almost immediate) the chain is covered again with liquid grey...
  17. Cracked Wolber Alpine rims - replacements?

    I have Wolber Alpine rims on my bike, but they have developed small cracks, parallel to the rim, around a couple of the eyelets. They're small, so I think I can leave them be while I look for...
  18. Replies
    10
    Views
    176

    Bam! Replaced! What better way to learn how to...

    Bam! Replaced! What better way to learn how to build a wheel than straight-up necessity?
  19. Replies
    14
    Views
    1,311

    I was searching these threads to find help in...

    I was searching these threads to find help in removing my uniglide cassette after not being able to understand the Sheldon Brown's 'neat trick' description. I got it to work and thought I would...
  20. I was searching these threads to find help in...

    I was searching these threads to find help in removing my uniglide cassette after not being able to understand the Sheldon Brown's 'neat trick' description. With the added understanding I got from...
  21. Replies
    10
    Views
    176

    So all I need is a new hub shell, essentially?...

    So all I need is a new hub shell, essentially? The '-glide' spliney sliding part will be interchangeable? What is this O.L.D you speak of?
  22. Replies
    10
    Views
    176

    What do you think might have caused it to happen?...

    What do you think might have caused it to happen? It's a well built Shimano hub so I have no idea why it would just up and break.



    Is the axle not under massive stress now? I wouldn't want to...
  23. Replies
    10
    Views
    176

    Halved Rear Hub Shell

    I've noticed that the shell of the rear hub I've been riding round has cracked right round the middle. Clearly, this is prone to catastrophic failure. It's a Shimano 7-speed Sante uniglide hub,...
  24. Replies
    16
    Views
    279

    Quick steering? I like the sound of that! Why...

    Quick steering? I like the sound of that! Why didn't the cranks work for the hills? Was it the biopace rings?
  25. Replies
    31
    Views
    648

    I looked at the frame measurements in the catalog...

    I looked at the frame measurements in the catalog and the 1200 (tri) and 912/712 (racers) share the exact geometry, and all but one measurement is the same as the Team, the top end racer. The one...
Results 1 to 25 of 82
Page 1 of 4 1 2 3 4