Advertise on Bikeforums.net



Search:

Type: Posts; User: blackangus; Keyword(s):

Page 1 of 2 1 2

Search: Search took 1.84 seconds.

  1. Replies
    8
    Views
    646

    Dick Pound is out!

    Dick Pound resigns from WADA

    http://www.cbc.ca/sports/story/2007/09/18/qc-pound0918.html
  2. Replies
    17
    Views
    681

    Haven't tried the Aksium's, but my Cosmos have...

    Haven't tried the Aksium's, but my Cosmos have been great. And that's with a 200-pounder on top of them!
  3. Replies
    2
    Views
    131

    Thanks Damocles. Do you know if it is an Open Pro...

    Thanks Damocles. Do you know if it is an Open Pro rim, or were there specific "Classics Pro" rims?
  4. Replies
    2
    Views
    131

    Help with Mavic wheel ID

    I picked up a set of wheels on flea-bay a couple months ago as a training set, but so far, haven't been able to figure out exactly what they are. I took them into the LBS on the weekend, but didn't...
  5. Replies
    8
    Views
    329

    I was looking at this again today and reading...

    I was looking at this again today and reading some of the feedback. Sounds like an awful lot of people think this was a hack job as well.
    ...
  6. Replies
    8
    Views
    329

    I watched it too Kris. It was very sensational,...

    I watched it too Kris. It was very sensational, but I wouldn't expect much more from Tom Harrington - not exactly known as a hard hitting journalist.

    Short version: Flandis is a cheater in denial,...
  7. Replies
    7
    Views
    204

    Yeah DT, there'll be a full pattern of holes for...

    Yeah DT, there'll be a full pattern of holes for the front roller - probably a pair either side of my design location about an inch apart.
  8. Replies
    7
    Views
    204

    I gotch' ya now! I was picturing doubled up...

    I gotch' ya now! I was picturing doubled up bearing on the outsides and couldn't see any benefit in that. I'm actually not worried at all about bending in the rollers - using 3 1/2" schd 40 pipe is...
  9. Replies
    7
    Views
    204

    Thanks for the PDF Chopper! Why do you suggest...

    Thanks for the PDF Chopper! Why do you suggest going with twin bearings? When I spec'd this particular bearing, I made sure I was well below the load and speed ratings - am I missing something? I can...
  10. Replies
    7
    Views
    204

    Roller setup - relative to wheelbase?

    I'm working on a little winter project at the moment - designing/fabricating a set of rollers. I've got a couple of questions about roller placement relative to wheelbase. I've got my rear rollers...
  11. Replies
    1,144
    Views
    49,987

    Test

    Test
  12. Replies
    22
    Views
    490

    I think you got the winter version - the holes...

    I think you got the winter version - the holes are for stud installation!
  13. Replies
    44
    Views
    1,121

    I've placed 2 or 3 orders with them now and all...

    I've placed 2 or 3 orders with them now and all have been about 2 weeks - I think it's more to do with Canada Customs than anything else though!
  14. Replies
    4
    Views
    131

    I've got my 60cm melon inside a size large Sweep....

    I've got my 60cm melon inside a size large Sweep. I'd guess I'm within the first (smaller) 1/3 of the size range.
  15. Replies
    64
    Views
    2,150

    My order took roughly 2 weeks to Halifax - longer...

    My order took roughly 2 weeks to Halifax - longer than I was hoping, but @$45CAN for 2 tires and 2 tubes - I won't complain!
  16. I just recieved my order from PBK last night. ...

    I just recieved my order from PBK last night.

    2 Vitt. Rubino Pro's and 2 Vitt. tubes for right around $45CAN.

    No tax/duties - just paid what was on the invoice!
  17. Piece of cake to figure it out with the bike in...

    Piece of cake to figure it out with the bike in front of me - but I was at work and the bike was at home!
    BTW - OD of the seat tube is 35.65mm.
  18. Anybody remember?

    Anybody remember?
  19. Seat Tube Dia - Mid 90's Trek ZX Frame??

    Anybody know, off the top of their head, what the seat tube diameter was on a mid 90's Trek ZX series (carbon tubes/alum lugs) frame? I'm looking at a front derailleur on Flea-bay and can't remember...
  20. I was thinking the same thing Oilman - not a true...

    I was thinking the same thing Oilman - not a true $500 build.

    I'm trying to do a $750 build, but it's looking more and more like $1000. Starting with an $80 CF/Alum frame/fork and $200 Mavic...
  21. Thread: passing out

    by blackangus
    Replies
    18
    Views
    451

    It's happened to me several times - mtn. biking...

    It's happened to me several times - mtn. biking mostly (passed out once and whited-out several times), but has happened during basketball & hockey (passed out & whited-out). I had always attributed...
  22. Demon - my problem is that this Trek frame...

    Demon - my problem is that this Trek frame doesn't have a replacement hanger - the dropout and hanger are one piece (mid 90's ZX series frame - CF/Alum). If I go with a Trek hanger, I have to set my...
  23. Anybody have any thoughts at all???

    Anybody have any thoughts at all???
  24. Critical spacing - DR hanger to hub axle?

    How critical is the rear derailleur spacing from the hub axle?

    I've got a Trek frame with a broken derailleur hanger (from the previous owner - not me). I picked up a Cannondale replacement hanger...
  25. Here's one for you guys - I just picked up a 10yr...

    Here's one for you guys - I just picked up a 10yr old CF/Alum frame, and some of the clearcoat is coming off the CF tubes. Any suggestions for sealing it back up?
Results 1 to 25 of 33
Page 1 of 2 1 2