Advertise on Bikeforums.net



Search:

Type: Posts; User: Mr. Fly; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 1.05 seconds.

  1. Replies
    23
    Views
    407

    Apart from the Dyna-Sys incompatibility, you may...

    Apart from the Dyna-Sys incompatibility, you may also want to return that BS79 and see if you can find a set of 7800 series BS78 bar-end shifters. They're probably discontinued but you can probably...
  2. Replies
    26
    Views
    738

    For pinholes, latex sealant seems to work really...

    For pinholes, latex sealant seems to work really well for me. I've pumped a couple of dozen mL of Stan's into my son's tubes and that seemed to have addressed his propensity to run over goat heads.
    ...
  3. Throwing it out there. Maybe the retainer...

    Throwing it out there. Maybe the retainer bearings were installed incorrectly in the first place. I've seen bearings that were flipped and that added to the overall stack height. It's usually quite...
  4. Replies
    5
    Views
    399

    PT systems have the right-side bearing pressed...

    PT systems have the right-side bearing pressed onto the BB spindle. The left-side bearing comes with the left BB cup. This is distinct from UT systems that have both left and right-side bearings...
  5. Do any of you drive? If you do, you can't take...

    Do any of you drive? If you do, you can't take the "polluting the environment" tack since the amount of pollution we cyclists cause by using any type of solvent/surfactant is infinitesimally small...
  6. I don't have a definitive answer for you except...

    I don't have a definitive answer for you except that end-caps are usually specific to a hub shell/body so I doubt slapping on a true-blue DT end cap will work, especially seeing that the rest of your...
  7. Replies
    8
    Views
    1,382

    Well, it depends. The whole point of the top cap...

    Well, it depends. The whole point of the top cap is to apply enough clamping force so that the headset is tight enough before the stem bolts are tightened. If you use an overly long 1">9/8" shim,...
  8. Replies
    20
    Views
    746

    I don't think it's the heat that's causing you...

    I don't think it's the heat that's causing you problems. The cable is likely stainless so you'll need special flux for it. Maybe something with zinc chloride in it.
  9. Despite the lengthy discourse, you've not...

    Despite the lengthy discourse, you've not answered the question.

    Are you taking Phil Wood at their word that these are waterproof or do you have other independent information collaborating to...
  10. I've seen this quote many times but Google...

    I've seen this quote many times but Google searches for submersible pump bearings or similar do not show any hits that are similar to what cartridge bearing seals are. It is interesting that a lot of...
  11. Replies
    30
    Views
    776

    I use latex tubes almost on a day-to-day basis....

    I use latex tubes almost on a day-to-day basis. The red ones from Challenge are used on my brevet/mixed-terrain bike and the green Michelin ones are used for commuting. Here are my real world...
  12. Replies
    40
    Views
    1,059

    Ultegra level mid/standard-reach caliper brakes...

    Ultegra level mid/standard-reach caliper brakes are available as model BR-R650 for about $50-60 per end. There are a few hits on Google and eBay. I have a pair and they're like any other Shimano...
  13. Replies
    54
    Views
    1,532

    If you have a cassette, remember to put a light...

    If you have a cassette, remember to put a light but noticeable coat of grease on the freehub body prior to installing the cassette. Many a squeak that was (incorrectly) attributed to BBs, cranks,...
  14. Replies
    13
    Views
    308

    Can't you tap the hole in the BB, drill a hole...

    Can't you tap the hole in the BB, drill a hole where the insert is, and use a short bolt to hold the guide?
  15. Replies
    4
    Views
    296

    Never tried it myself, but the Berthoud...

    Never tried it myself, but the Berthoud "vertical" decaleur appears as if it should work with the Nitto CT-80.
  16. It's probably less structurally sound due to the...

    It's probably less structurally sound due to the many unsupported rim sections (unless the rim is reinforced and unnecessarily heavy). And they can be a pain to true – the sections with no spokes...
  17. Replies
    12
    Views
    1,043

    Most lights sold for bicycle use are pretty...

    Most lights sold for bicycle use are pretty crappy in terms of light quality. They use commodity parts and typically have a commodity reflector or lens that produces a symmetrically conical beam....
  18. If you like, you can remove the Ritchey logos...

    If you like, you can remove the Ritchey logos with some #0000 steel wool and oil. Just go easy and the logos will magically vanish without marks. On my friend's Della Santa with the exact Ritchey...
  19. If you like your Campagnolo Ultra-Torque cranks,...

    If you like your Campagnolo Ultra-Torque cranks, why not wait for the Over-Torque cranks in 2014
  20. Replies
    35
    Views
    1,150

    While technically true, I have a hard time...

    While technically true, I have a hard time feeling if my lights are switched on (which will be when it has the highest drag) or off. This is more than 3 watts of additional drag that I cannot feel...
  21. In addition, remember to unwind the limit screws....

    In addition, remember to unwind the limit screws. With the limit screws fully retracted, I usually have very little problem putting the two sections back together. As FBinNY stated, this operation...
  22. Replies
    58
    Views
    2,591

    I don't know if you know the context behind that...

    I don't know if you know the context behind that statement made by the REI employee, or if you've ever worked retail. Some customers can be so clueless and yet so insistent that they are correct that...
  23. Replies
    99
    Views
    3,190

    Well, was this dude Asian? In Taiwan, where Giant...

    Well, was this dude Asian? In Taiwan, where Giant is based, its Chinese name is 捷安特. Since this is the name of Giant in its native language, I'm going to claim that it is the most correct reference....
  24. Replies
    7
    Views
    382

    Just a word of caution with Ortliebs, with what...

    Just a word of caution with Ortliebs, with what you throw in them...

    They are extremely waterproof. But that also means they keep moisture in as well as moisture out. I had the unfortunate...
  25. Replies
    6
    Views
    440

    Are you set on Honjos, or will a nice aluminum...

    Are you set on Honjos, or will a nice aluminum fender do? A decent (and much cheaper) alternative to Honjo fenders are Tanaka fenders. They only come in the smooth version (no hammered goodness) but...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4