Pedals too tight to remove (help!)
#1
Junior Member
Thread Starter
Join Date: Apr 2005
Posts: 10
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Pedals too tight to remove (help!)
I'm trying to remove some Ritchey clipless pedals to switch over to my new bike. The problem is that the pedals have been on the old bike for 8-9 years, most of which the bike has been in storage. I'm worried they are rusted on, any suggestions as to how to oil them up or something and get them loose? I even tried hammering the end of the wrench to free them up but they are too tight. I'm clueless mechanically and would appreciate any help. THanks!
#2
Ferrous wheel
Join Date: Apr 2005
Location: New Orleans
Posts: 1,388
Bikes: 2004 Gunnar Rock Hound MTB; 1988 Gitane Team Pro road bike; 1986-ish Raleigh USA Grand Prix; mid-'80s Univega Gran Tourismo with Xtracycle Free Radical
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I would try squirting some Liquid Wrench around the thread area. Sometimes applying heat helps, too.
#3
Senior Member
Join Date: Jun 2003
Posts: 18,138
Bikes: 2 many
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 1266 Post(s)
Liked 323 Times
in
169 Posts
Put some penetrating oil on the threads and leave it over night.
Are you using a bicycle pedal wrench? This is a big help. The left (non drive side) is reverse thread. Hold the bike still ( put the bike on the ground) and push down on the wrench towards the floor. If this does not do it or you are not sure about reverse threads take it to a bike shop.
Are you using a bicycle pedal wrench? This is a big help. The left (non drive side) is reverse thread. Hold the bike still ( put the bike on the ground) and push down on the wrench towards the floor. If this does not do it or you are not sure about reverse threads take it to a bike shop.
#4
I'd rather be riding
Join Date: Jan 2005
Location: Melbourne, Australia
Posts: 144
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
when you get the pedals off and before putting them on your other bike, grease the threads to prevent this problem next time.
Hace fun!
Hace fun!
#5
Senior Member
Join Date: Oct 2004
Location: Dublin, Ireland
Posts: 379
Bikes: Specialized Sirrus Sport, Specialized Stumpjumper Comp, Brompton, Trek 1500
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Originally Posted by blockzilla
I'm trying to remove some Ritchey clipless pedals to switch over to my new bike. The problem is that the pedals have been on the old bike for 8-9 years, most of which the bike has been in storage. I'm worried they are rusted on, any suggestions as to how to oil them up or something and get them loose? I even tried hammering the end of the wrench to free them up but they are too tight. I'm clueless mechanically and would appreciate any help. THanks!
#6
Senior Member
Join Date: Oct 2004
Posts: 187
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
All you need is leverage. Get a long pipe and put it over the wrench. Use this leverage to free your pedals. Make sure you are loosening them in the correct direction – I believe to the rear of the bike.
#7
I couldn't car less.
Join Date: Nov 2003
Posts: 4,397
Bikes: Ritchey P-series prototype, Diamondback, Nishiki Triathelon Pro.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Is there a hex key slot on the end of the spindle? (otherside of the crank arm.)
If so, use a hex key and a wrench.
If so, use a hex key and a wrench.
#8
Bicycle Rider & Mechanic
Join Date: Dec 2004
Location: Delaware
Posts: 686
Bikes: Superlight, Dragon Team, Eclipse, Om Flyer
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I encountered this problem today what I did was flipped my bike upside down and I had my priend hold the pedal down with his foot and I pushed the wrenchtoward the rear wheel, it was only my right pedal that was giving me trouble though. I recommend trying this as it worked for me.
#10
Junior Member
Thread Starter
Join Date: Apr 2005
Posts: 10
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks everyone for the help. I decided to play it safe and took it to my LBS to pop them off for me. They are now happily at home on my new ride.