Shortening a Seat Tube
#1
Senior Member
Thread Starter
Join Date: May 2005
Location: in the hills of Orange, CA
Posts: 1,355
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Shortening a Seat Tube
I have a steel tandem with a rear seat tube that sticks out above the top tube, with an external clamp for the seatpost. In order to accommodate a shorter stoker, I'd like to cut about 1 cm from the seat tube. How can I make a good cut without ruining the frame? And do I have to lengthen the slot facing the rear of the bike? Or should I take the tandem to a framebuilder to do all this?
#2
Senior Member
Join Date: Feb 2005
Location: Santa Cruz, CA
Posts: 158
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You can do it! You might try using a fork cutting guide to get a straight cut. Yes, you should lenghten the slit in the back to its original length. I think a hack-saw should do it just fine. Clean up the cut with a file and you're done. I've never done it, but I don't think you should be afraid to work on your bike. good luck.
-Nick
-Nick
#3
Senior Member
Join Date: Dec 2005
Location: Orlando
Posts: 301
Bikes: homebuilt FWD recumbents, Genesis 20" folding bike, 1986 Schwinn Tempo, Cannondale Beast of the East, 70's Peugeot
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
How much length sticks up from the top tube? This may sound crazy to some, but if there is enough length there (for tool access), I would suggest that you get a pipe/tubing cutter and use that to make the cut. It will make a nice, clean, SQUARE cut on the tube.
tube cutter
tube cutter
#4
Senior Member
Thread Starter
Join Date: May 2005
Location: in the hills of Orange, CA
Posts: 1,355
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Here's a couple of pics, sorry they're a little fuzzy. Looks like all I can take off is 0.5 cm off the seattube, otherwise the slot in the back would be lower than the welds for the seat stays. The crosshatched area is the part that the seat collar clamp would cover. So I have to ask myself is it worth the trouble for just 0.5 cm ....
#5
Senior Member
Join Date: Feb 2005
Location: Santa Cruz, CA
Posts: 158
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You might try a seatpost with a lower head profile. This means that the distance from the maximun insetion level to the saddle rails is less. You might also try a saddle with less padding (SLR, etc,...) to help bring the effective saddle height lower.
I have seen frames where the seat tube slit extends below the attachment of the seatstays. I don't know if sliting below this level will copromise integrity.
Any frame builders want to comment????
-Nick
I have seen frames where the seat tube slit extends below the attachment of the seatstays. I don't know if sliting below this level will copromise integrity.
Any frame builders want to comment????
-Nick
#6
Member
Join Date: Dec 2005
Location: tallahassee
Posts: 28
Bikes: orbea steel road bike, my very own track bike, penny farthing.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
there are a couple other options. i have seen seat posts that were build for aluminum frames that were built without any sort of binding. the seat post worked like a quill stem. it may be hard to find and if you find it, it may not fit the seat tube.(i believe one of these frames was made by schwinn)
another option is to make a binding like strawberry cycles
https://bikelugs.com/pacentigallery/s...awberry06.html
this would take some work, but it would let you cut the whole length off of the seat tube.
another option is to make a binding like strawberry cycles
https://bikelugs.com/pacentigallery/s...awberry06.html
this would take some work, but it would let you cut the whole length off of the seat tube.
#7
Member
Join Date: Dec 2005
Location: tallahassee
Posts: 28
Bikes: orbea steel road bike, my very own track bike, penny farthing.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts