Does this open clockwise or counter-clockwise? Picture inside.
#1
Junior Member
Thread Starter
Join Date: May 2009
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Does this open clockwise or counter-clockwise? Picture inside.
I am taking apart bottom bracket on my bike and do not want to damage the thread.
So do I turn this CW or CCW? (My guess would be CW, but I need to make sure).
So do I turn this CW or CCW? (My guess would be CW, but I need to make sure).
#2
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
Hard to say. There have been different standards through the years in different countries of origin. What kind of bike is it, and what year?
But, it is most likely CW to loosen. If I had no idea which way to go with it, I would try that first.
jim
But, it is most likely CW to loosen. If I had no idea which way to go with it, I would try that first.
jim
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#3
Guest
Posts: n/a
Mentioned: Post(s)
Tagged: Thread(s)
Quoted: Post(s)
Being that that is the drive side, it will most likely loosen over the top, counter clock wise. The other side will loosen clock wise, most likely. In most cases, pedals and bb's tighten over the top towards the front of the bike.
#6
Senior Member
this unit come off clockwise.no , english is not equate to SAE in this case.
#8
Senior Member
Read the stamped info. If it says 1.37 x 24, it's English and unscrews CW. If it say 36 x 24 it's Italian and unscrews CCW.
#9
use your best eye
Join Date: Mar 2006
Location: Olympia, Washington
Posts: 3,050
Bikes: '75 Bertin, '93 Parkpre Team 925, '04 Kona King Kikapu, '05 Bianchi Vigorelli
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
For the more knowledgeable here- what if it's French?
__________________
"I tell you, We are here on earth to fart around, and don't let anybody tell you any different." - Kurt Vonnegut jr.
"I tell you, We are here on earth to fart around, and don't let anybody tell you any different." - Kurt Vonnegut jr.
#10
OUTLAW BIKER
Join Date: Aug 2008
Location: So Cal
Posts: 512
Bikes: Eddy Merckx team 7-11 Corsa Extra Full Dura Ace, 2015 Equalizer Electric Fat Tire Bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Usually: left side left side threads... right side right side threads, right side lefty lucy
#11
Senior Member
#12
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
#13
Your mom
Join Date: Aug 2006
Posts: 2,544
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Usually: left side left side threads... right side right side threads, right side lefty lucy
If your bike is not Italian, that cup unscrews clockwise. And you're most likely going to need to honk on it. Try the Sheldon tool and a big breaker bar or pipe for more leverage.
#14
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
Or, if it is French (sometimes), or even Spanish.
j
j
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#17
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4337 Post(s)
Liked 2,980 Times
in
1,617 Posts
Italian BBs are threaded lefty loosey on the fixed cup but the threads themselves are a little different too - what do the markings say on there?
36 mm x 24 TPI = Italian
1.37 in x 24 TPI = English
36 mm x 24 TPI = Italian
1.37 in x 24 TPI = English
#18
Junior Member
Thread Starter
Join Date: May 2009
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The marking indeed says 36x24. The BB is made by Shimano but the frame is Italian (old steel Miche frame).
The reason why I asked is because I nearly turned cherry red trying to unscrew this and I was still not able to! It seems to be very, VERY tight!
Edit: I almost shat myself trying to unscrew it! It won't come off!
The reason why I asked is because I nearly turned cherry red trying to unscrew this and I was still not able to! It seems to be very, VERY tight!
Edit: I almost shat myself trying to unscrew it! It won't come off!
Last edited by KO3AK; 05-22-09 at 05:18 PM.
#19
Senior Member
Join Date: Oct 2007
Location: SoCal
Posts: 1,169
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The marking indeed says 36x24. The BB is made by Shimano but the frame is Italian (old steel Miche frame).
The reason why I asked is because I nearly turned cherry red trying to unscrew this and I was still not able to! It seems to be very, VERY tight!
Edit: I almost shat myself trying to unscrew it! It won't come off!
The reason why I asked is because I nearly turned cherry red trying to unscrew this and I was still not able to! It seems to be very, VERY tight!
Edit: I almost shat myself trying to unscrew it! It won't come off!
#20
surly old man
Join Date: Sep 2006
Location: Carlisle, PA
Posts: 3,392
Bikes: IRO Mark V, Karate Monkey half fat, Trek 620 IGH, Cannondale 26/24 MTB, Amp Research B3, and more.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 46 Post(s)
Likes: 0
Liked 42 Times
in
18 Posts
And when that fails, get thee to the Sheldon tool that (almost) never fails.
jim
jim
__________________
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
Cross Check Nexus7, IRO Mark V, Trek 620 Nexus7, Karate Monkey half fat, IRO Model 19 fixed, Amp Research B3, Surly 1x1 half fat fixed, and more...
--------------------------
SB forever
#21
Senior Member
For loosening any stuck fastener, first make sure you have plenty of leverage. If you are using a 12" long tool, either find a longer tool or find an extension for it. For a stuck bottom bracket, I'd go for at least 24" if not more. Second, make sure you can hold the tool stable while you really crank on it. This may mean having a (brave) helper hold it in place or finding a way to securely clamp the tool in place if it won't stay there by itself.
Using a little penetrating oil like PB Blaster wouldn't hurt either.
#22
Senior Member
Join Date: Oct 2007
Location: SoCal
Posts: 1,169
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Rubber? Really? I've had luck loosening corroded fasteners on cars using the (steel) hammer and wrench approach. I don't see how a rubber mallet would transfer enough impact energy to do any good.
For loosening any stuck fastener, first make sure you have plenty of leverage. If you are using a 12" long tool, either find a longer tool or find an extension for it. For a stuck bottom bracket, I'd go for at least 24" if not more. Second, make sure you can hold the tool stable while you really crank on it. This may mean having a (brave) helper hold it in place or finding a way to securely clamp the tool in place if it won't stay there by itself.
Using a little penetrating oil like PB Blaster wouldn't hurt either.
For loosening any stuck fastener, first make sure you have plenty of leverage. If you are using a 12" long tool, either find a longer tool or find an extension for it. For a stuck bottom bracket, I'd go for at least 24" if not more. Second, make sure you can hold the tool stable while you really crank on it. This may mean having a (brave) helper hold it in place or finding a way to securely clamp the tool in place if it won't stay there by itself.
Using a little penetrating oil like PB Blaster wouldn't hurt either.
Have removed several of the old type BBs using this method and it DOES work for me.
If it were really stuck badly I guess I might get a bigger hammer but haven't needed the 16# Sledge on a bike yet.
#23
Junior Member
Thread Starter
Join Date: May 2009
Posts: 6
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I didn't have neither a hammer nor a mallet so I used rubber part of a big adjustable wrench to hammer on the Park BB tool. It came open after a couple of whacks.