Correct seat post height?
#1
Junior Member
Thread Starter
Join Date: Sep 2009
Location: Chitella
Posts: 20
Bikes: 2007 Masi Speciale Fixed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Correct seat post height?
Just bought a masi speciale fixed recently, and had the LBS fix a few things. when i picked it up, noticed the seat height was set very high. I know some riders like to set it exaggeratedly high (i.e. massan); which may hurt their back, but their riding rocks. Thoughts on what is the way to properly set the height?
ps. apologies if this is a lame/newbie type question.
ps. apologies if this is a lame/newbie type question.
#2
matters cryptozoological
Join Date: Dec 2007
Posts: 149
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
at the crank's 6 o'clock you should have a slight bend in your leg--should not be fully straight. the seat should be set back enough so that when your foot is at the 3 o'clock, your knee is above the ball of your foot.
it's not a precise science, use these guides as a starting point. people usually find their sweet spot from there.
it's not a precise science, use these guides as a starting point. people usually find their sweet spot from there.
#3
("'\( *,..,*)/"')
Join Date: Jun 2008
Location: San Jose, CA
Posts: 209
Bikes: 2010 Specialized Allez Steel| IRO Mark V fixed gear
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Just bought a masi speciale fixed recently, and had the LBS fix a few things. when i picked it up, noticed the seat height was set very high. I know some riders like to set it exaggeratedly high (i.e. massan); which may hurt their back, but their riding rocks. Thoughts on what is the way to properly set the height?
ps. apologies if this is a lame/newbie type question.
ps. apologies if this is a lame/newbie type question.
#5
Senior Member
Join Date: Jan 2005
Posts: 1,301
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 12 Times
in
1 Post
another good rule of thumb (ie: starting point) is 88% of your inseam length. lemond's number, i think.
measure your actual inseam while barfoot, don't use pants size. and the saddle height is measured from the center of the bottom bracket (crank spindle) to the top of the saddle, along the seat tube (ie: not straight vertical).
measure your actual inseam while barfoot, don't use pants size. and the saddle height is measured from the center of the bottom bracket (crank spindle) to the top of the saddle, along the seat tube (ie: not straight vertical).
#7
Senior Member
Join Date: Sep 2006
Location: Van BC
Posts: 3,744
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If you're going to measure your inseam for cycling, the right way to do it is to get up against a wall, push a hardcover book against the wall, and then slide it up into your crotch, pushing hard enough for it to be somewhat uncomfortable. (Not kidding). Then, measure the height of the book from the floor. The fit formulas all assume a measurement of this type.
Another method to find the right ball park is, get seat height so your heels can barely touch the pedals at the bottom of the downstroke.
Really though, the only way to get fit perfect is to experiment. Once you have your saddle in the right ballpark, moving it up or down 1/8" can make a huge difference (good or bad) so remember to keep adjustments small.
Another method to find the right ball park is, get seat height so your heels can barely touch the pedals at the bottom of the downstroke.
Really though, the only way to get fit perfect is to experiment. Once you have your saddle in the right ballpark, moving it up or down 1/8" can make a huge difference (good or bad) so remember to keep adjustments small.
#8
Nü-Fred
Join Date: Jul 2009
Location: Brooklyn, NY
Posts: 1,517
Bikes: Torelli Tipo Uno (stolen), Peugeot Nice, Mercier Kilo TT
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sheldon Brown's wisdom:
I like to think that William Blake summed it up nicely 200 years ago when he said:I suggest gradually raising your saddle, perhaps half an inch (1 cm) at a time. Each time you raise it, ride the bike. If it doesn't feel noticeably worse to ride, ride it for at least a couple of miles/km. If it had been too low before, your bike will feel lighter and faster with the new riding position. If raising the saddle improved things, raise it again, and ride it some more. Keep doing this until you reach the point where the saddle is finally too high, then lower it just a bit.
"You never know what is enough
until you know what is too much."
until you know what is too much."
#10
Fixed-gear roadie
Join Date: Dec 2008
Location: Wilmington, NC
Posts: 1,048
Bikes: 2008 Masi Speciale Fixed
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I like mine as high as possible without discomfort from having my leg straightened out too far.
As for discomfort from being hunched over, that's a fit issue to be resolved by changing the position of the bars, not the seatpost. The seatpost adjustment is for your legs, period.
As for discomfort from being hunched over, that's a fit issue to be resolved by changing the position of the bars, not the seatpost. The seatpost adjustment is for your legs, period.
#11
Senior Member
Join Date: Mar 2007
Posts: 6,401
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 13 Times
in
13 Posts
Use mander's method of obtaining your inseam. Multiply this result by .883. This is your seat height, measured from the center of the bottom bracket to the top of the saddle, approximately in the middle. This is known as the LeMond formula, but is actually the Renault/Gitane formula taught to LeMond when he rode for Cyrille Guimard. The number is not cast in stone, but does guarantee that your seat height will not be incorrect. In can be adjusted up and down a centimeter or so if desired.