installing new handlebars and brakes, some beginner questions...
#1
Junior Member
Thread Starter
Join Date: Sep 2010
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
installing new handlebars and brakes, some beginner questions...
hey all,
i'm a newbie to the scene of singlespeed/fixed gears. i bought a single speed a few years ago, when i had no idea what i really got.
but recently i've decided to try to build this thing up a little bit. i'm a definite beginner as far as knowledge.. i've been reading around on sheldon brown's page and these forums, but i have a few questions.
my first project is installing new bullhorn bars and brakes, and then taping them.
(my frame is a trek of some sort. i'm not even sure which model)
questions:
how do i know which size bullhorns will fit my stem? do i need to measure the opening of the stem? do i then use the size of the bars to find a brake that fits? do i want bars that are pre-drilled? or do i just want to take the cables underneath the bartape. are there any good tutorials for bartaping?
also, does anyone have recommendations for bullhorn/reverse-brake combos? i'm on a pretty strict budget, so cheaper is better. mostly i'm just trying to make sure i don't buy the wrong size or the wrong parts.
any help, advice, or cautionary tales would be super helpful! in the meantime i'll keep looking around.
thanks so much!
i'm a newbie to the scene of singlespeed/fixed gears. i bought a single speed a few years ago, when i had no idea what i really got.
but recently i've decided to try to build this thing up a little bit. i'm a definite beginner as far as knowledge.. i've been reading around on sheldon brown's page and these forums, but i have a few questions.
my first project is installing new bullhorn bars and brakes, and then taping them.
(my frame is a trek of some sort. i'm not even sure which model)
questions:
how do i know which size bullhorns will fit my stem? do i need to measure the opening of the stem? do i then use the size of the bars to find a brake that fits? do i want bars that are pre-drilled? or do i just want to take the cables underneath the bartape. are there any good tutorials for bartaping?
also, does anyone have recommendations for bullhorn/reverse-brake combos? i'm on a pretty strict budget, so cheaper is better. mostly i'm just trying to make sure i don't buy the wrong size or the wrong parts.
any help, advice, or cautionary tales would be super helpful! in the meantime i'll keep looking around.
thanks so much!
#2
a bored kid
Join Date: Jul 2010
Location: East Lansing, MI
Posts: 177
Bikes: Year unknown CCM Targa conversion
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Heya. Measure the handlebar-clamp part of the stem to get the bar diameter. It's usually in mm.
As for pre-drilled/sub-tape, it's your preference or whatever you can find. I just wrapped my brake cable underneath. First I taped the cable to the bar really tightly with duct tape so it wouldn't move around while I was wrapping. Then I just wrapped over it. Common sense though, make sure to leave plenty of slack in your brake cables so you can turn your handlebars, haha. I don't know of any bar wrapping tutorials, but I always wrap inside-out, that way I get really clean starting lines that don't need electrical tape. Lift up the brake hood and fiddle the tape around that, then just flip the hood down. Looks good man. It kinda takes practice, maybe five wraps to get awesome at it, but it's really not rocket science. It's kinda hard to do a TERRIBLE wrap job unless you're drunk and in a mad rush.
Sorry, can't really help with bullhorns, I ride drops. I'm pretty sure it's all very doable; a handlebar is a handlebar, right?
Hopefully I helped a bit!
As for pre-drilled/sub-tape, it's your preference or whatever you can find. I just wrapped my brake cable underneath. First I taped the cable to the bar really tightly with duct tape so it wouldn't move around while I was wrapping. Then I just wrapped over it. Common sense though, make sure to leave plenty of slack in your brake cables so you can turn your handlebars, haha. I don't know of any bar wrapping tutorials, but I always wrap inside-out, that way I get really clean starting lines that don't need electrical tape. Lift up the brake hood and fiddle the tape around that, then just flip the hood down. Looks good man. It kinda takes practice, maybe five wraps to get awesome at it, but it's really not rocket science. It's kinda hard to do a TERRIBLE wrap job unless you're drunk and in a mad rush.
Sorry, can't really help with bullhorns, I ride drops. I'm pretty sure it's all very doable; a handlebar is a handlebar, right?
Hopefully I helped a bit!
#3
Noob.
Join Date: Apr 2010
Location: NYC/NJ
Posts: 503
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
i run a cross top lever near the stem when i run bullhorns and they are just fine. i chose to go this route because it was cheaper! plus you dont need to run cables under any bar tape.
#4
Junior Member
Thread Starter
Join Date: Sep 2010
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
thanks guys!
any info is helpful. some of the articles by sheldon brown and on these forums use terms that are a little hard to understand for a complete beginner.
another question, is there any way to install both brake levers to the front wheel? i don't want a rear brake, but it'd be nice to access the front brake from either hand position.
thanks!
any info is helpful. some of the articles by sheldon brown and on these forums use terms that are a little hard to understand for a complete beginner.
another question, is there any way to install both brake levers to the front wheel? i don't want a rear brake, but it'd be nice to access the front brake from either hand position.
thanks!
#5
Noob.
Join Date: Apr 2010
Location: NYC/NJ
Posts: 503
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
do you mean at the end of the horns and near the stem? you can use the bar end type lever and mate it to an in-line cross lever. here is a link to a similar setup but on road drops. same concept though.
https://www.parktool.com/repair/readhowto.asp?id=146
https://www.parktool.com/repair/readhowto.asp?id=146
#6
Junior Member
Thread Starter
Join Date: Sep 2010
Posts: 5
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
no, i don't think that's what i mean.
i'm talking about one brake on each side of the bars (where typically you would find one front and one rear), but in this case both control the front brake.
does that make sense?
i'm talking about one brake on each side of the bars (where typically you would find one front and one rear), but in this case both control the front brake.
does that make sense?
#7
Senior Member
Join Date: Jan 2010
Location: Seattle, WA
Posts: 125
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thread
Thread Starter
Forum
Replies
Last Post
the sci guy
Bicycle Mechanics
31
02-16-14 04:23 AM