so i just got my windsor clockwork in the mail.. (question)
#1
Junior Member
Thread Starter
Join Date: Feb 2012
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
so i just got my windsor clockwork in the mail.. (question)
hey everyone. i just got my windsor clockwork in the mail. i'm working on putting it together right now. got the saddle, stem, and pedals on. i THINK i put the front wheel on right - but both the general owner's manual and the online video i watched talk about a quick release, and i didn't see that in the package. does anyone else who got a windsor clockwork from BD have a quick release/do all bikes come with that/am i missing this piece?
i just unscrewed the end nuts, slid the wheel into place, and put them back on and tightened them. it seems right, it rolls back and forth. but was that right?
sorry this is such a dumb question - this is my first bike. thanks!
i just unscrewed the end nuts, slid the wheel into place, and put them back on and tightened them. it seems right, it rolls back and forth. but was that right?
sorry this is such a dumb question - this is my first bike. thanks!
#2
Senior Member
Join Date: Jul 2006
Posts: 3,063
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1216 Post(s)
Liked 185 Times
in
116 Posts
You did fine. Make sure to torque them to 260-390 in-lbs.
https://www.parktool.com/blog/repair-...s-and-concepts
https://www.parktool.com/blog/repair-...s-and-concepts
#3
Junior Member
Thread Starter
Join Date: Feb 2012
Posts: 11
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
no idea how to go about that. but i'm bringing my bike into my LBS on thursday so they can true my tires up for me. i was going to ask them to double check my tire assembly.
#4
Senior Member
Join Date: Jan 2011
Location: New York
Posts: 201
Bikes: Brooklyn Machine Works Gangsta Track, Bianchi Pista Concept 2005, Cannondale CAAD9, Klein Fervor
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Do not ride it yet. Take it to a bike shop for them to grease up the seatpost/cog/lockring/bottom bracket/pedals. After that is done you should be good to go. While you are there ask them many questions about how each part of the bike works and how to adjust things when you need to.
#5
Senior Member
Join Date: Apr 2005
Location: Brownsville, TX
Posts: 2,174
Bikes: Surly CC
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You did fine. Make sure to torque them to 260-390 in-lbs.
https://www.parktool.com/blog/repair-...s-and-concepts
https://www.parktool.com/blog/repair-...s-and-concepts
#6
Brown Bear, Sqrl Hunter
Do not ride it yet. Take it to a bike shop for them to grease up the seatpost/cog/lockring/bottom bracket/pedals. After that is done you should be good to go. While you are there ask them many questions about how each part of the bike works and how to adjust things when you need to.
Have the LBS check everything over.
#7
Senior Member
Join Date: Jul 2006
Posts: 3,063
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1216 Post(s)
Liked 185 Times
in
116 Posts
Under-tightening can cause the fastener to loosen over time. Over-tightening can destroy the fastener or greatly reduce it's lifespan. Why wouldn't a prudent person want to make sure the proper torque is applied?
Last edited by Spoonrobot; 02-08-12 at 01:13 PM.
#8
Makin it Trizzle
Join Date: Aug 2010
Posts: 196
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Edit: nice fix
Last edited by I Have a Bike; 02-08-12 at 01:23 PM.
#9
hamcycles.com
Join Date: Mar 2011
Posts: 3,705
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
sure there's nothing wrong with it and it's better to do so if the option is there but...
I've also never seen anyone do it. even the more delicate stuff I've very very rarely seen a torque wrench come out to play (shops included).
y so srs robot
I've also never seen anyone do it. even the more delicate stuff I've very very rarely seen a torque wrench come out to play (shops included).
y so srs robot
#10
Senior Member
Join Date: Jun 2008
Location: Chicago, IL
Posts: 513
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
It's not axle nuts rocket science. Just tightened them to the point it won't come off if you hit a huge bump.
#11
Senior Member
Yeah man, what everyone else said don't ride it yet. It's gonna be the back wheel you should be worried about the cog and lock ring should be extra tight.
Last edited by Philasteve; 02-08-12 at 05:43 PM.
#12
Senior Member
Join Date: Jul 2006
Posts: 3,063
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1216 Post(s)
Liked 185 Times
in
116 Posts
"Really tight?"
Well, that stunning specification is going to vary greatly depending on the person, the tool used, the drop-out types and even the fastener type. The point is that it pays to be aware of proper torque specs. Even something as general as "around 60 pounds of force on the end of a 6-inch wrench" is better than nothing.
#13
Fresh Garbage
If I were a shop mechanic I would use a torque wrench to reduce liability. For myself, my wheel is on and off most often far from home. At least people make some connection to tighten axle bolts. It is suprising how many people can't operate a quick release correctly or skip the QR aspect all together and use the lever like a wingnut
#14
Senior Member
Join Date: Dec 2010
Location: Above ground, Walnut Creek, Ca
Posts: 6,681
Bikes: 8 ss bikes, 1 5-speed touring bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 86 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
think about a QR skewer on front and rear wheels. anybody use a torque wrench to adjust and latch those? i don't think so. we guess, and say to ourselves "ok, that's good". or something to that effect.
most of us learned to tighten a nut by the time we were ten years old. a couple of stripped threads, rounded off heads, and snapped bolts and we were there.
then there's my brother-in-law who refuses to stop tightening nuts until beads of sweat appear on his forehead.
BTW, least anyone think i regard torque wrenches as useless, i would recommend them for many high performance engine type applications, i.e. head bolts, big end bearing bolts, crankshaft bearing bolts, headers, clutch plates, flywheels and many others. bikes are low stress by comparison.
most of us learned to tighten a nut by the time we were ten years old. a couple of stripped threads, rounded off heads, and snapped bolts and we were there.
then there's my brother-in-law who refuses to stop tightening nuts until beads of sweat appear on his forehead.
BTW, least anyone think i regard torque wrenches as useless, i would recommend them for many high performance engine type applications, i.e. head bolts, big end bearing bolts, crankshaft bearing bolts, headers, clutch plates, flywheels and many others. bikes are low stress by comparison.
Last edited by hueyhoolihan; 02-09-12 at 12:54 AM.
#15
Senior Member
Join Date: Apr 2005
Location: Brownsville, TX
Posts: 2,174
Bikes: Surly CC
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Spoon,
I didn't take offense either way. I can appreciate the value of using a torque wrench. I merely said that I've never seen one used at a bike shop in my 38 years. It doesn't mean that its right or wrong.
I didn't take offense either way. I can appreciate the value of using a torque wrench. I merely said that I've never seen one used at a bike shop in my 38 years. It doesn't mean that its right or wrong.
#16
Senior Member
Join Date: Jul 2006
Posts: 3,063
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 1216 Post(s)
Liked 185 Times
in
116 Posts
think about a QR skewer on a front and rear wheels. anybody use a torque wrench to adjust and latch those? i don't think so. we guess and say to ourselves "ok, that's good", or something to that effect.
I mentioned this earlier. If you can't do it the right way at least have an idea of how to properly do it "wrong."
#17
Senior Member
Join Date: Apr 2011
Location: Sheboygan, WI
Posts: 383
Bikes: 2010 Windsor The Hour, 1982 Fuji Supreme
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
What the hell happened here? It's a frickin nut. You tighten it.
Anyways, I'm surprised the headset didn't give you more trouble. Maybe mine had just been jostled apart more during shipping. But please do have a pro check it all out for you. And if they don't charge, be awesome and buy some accessories from them. Buy accessories anyways.
Anyways, I'm surprised the headset didn't give you more trouble. Maybe mine had just been jostled apart more during shipping. But please do have a pro check it all out for you. And if they don't charge, be awesome and buy some accessories from them. Buy accessories anyways.
#18
Senior Member
Join Date: Apr 2005
Location: Brownsville, TX
Posts: 2,174
Bikes: Surly CC
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Spoon is still correct, even if the decidedly poor attempt at English makes me vomit a little in my mouth. The info, however, is correct.
#19
Senior Member
Join Date: Dec 2010
Location: Above ground, Walnut Creek, Ca
Posts: 6,681
Bikes: 8 ss bikes, 1 5-speed touring bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 86 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
...anyway, it reminds me of the poster in my protologists office that outlines (in 10 steps) how to sit on the toilet and take a crap. i actually DID read that one. and what was surprising was that i routinely performed 6 of the 10 steps!!!
Last edited by hueyhoolihan; 02-09-12 at 01:05 AM.
Thread
Thread Starter
Forum
Replies
Last Post
Leukybear
Singlespeed & Fixed Gear
5
12-04-10 03:38 PM