Best floor pump for HED 3
#1
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Best floor pump for HED 3
I'm trying to avoid the crack pipe solution.... Anyone have any success with Topeak joeblow or silca pista series?
#4
Hi, I'm Bryan.
Join Date: Jun 2010
Location: Chicago
Posts: 2,650
Bikes: 2010 Focus Mares
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Any floor pump on the market is gonna be fine, provided you are using it properly and it will take the right valve type.
Last edited by jimmytango; 03-15-13 at 01:00 AM.
#6
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I've tried 3 different floor pumps that do not work. The carbon cutout for the valve stem is extremely tight. This is an HED H3 tri spoke I'm referring to.
#8
Fresh Garbage
Did you try any pumps at a shop? You may want to ask in the Mechanics forum or one of the racing forums like Track and Triathalon where you will more likely find a person that also owns one.
#9
Senior Member
Join Date: Oct 2010
Location: San Francisco, CA
Posts: 3,059
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
A few weeks ago.
Timjohnson, if it's tight clearances that you're working with, try a Leyzne floor pump. They have a minimalist screw-on presta valve.
Timjohnson, if it's tight clearances that you're working with, try a Leyzne floor pump. They have a minimalist screw-on presta valve.
#10
THE STUFFED
Join Date: Oct 2009
Location: San Francisco, CA
Posts: 12,671
Bikes: R. Sachs Road; EAI Bareknuckle; S-Works Enduro
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 361 Post(s)
Likes: 0
Liked 20 Times
in
17 Posts
I use a silca super pista to inflate mine. Best rebulidable pump out there imo. We're talking about a legacy brand; I have one that's 40 years old handed down to me and still kicking! Either only takes a few actuations to get up to 120+ PSI.
Forget the zipp crack pipe. It sucks! You'll find it always blowing off the valve from the pressure if you don't awkwardly press the chuck down on the valve while inflating.
I personally use a hirame chuck for all my wheels with a locking mechanism that's slim and unintrusive enough to fit aero wheel cut outs, worth every penny.
Forget the zipp crack pipe. It sucks! You'll find it always blowing off the valve from the pressure if you don't awkwardly press the chuck down on the valve while inflating.
I personally use a hirame chuck for all my wheels with a locking mechanism that's slim and unintrusive enough to fit aero wheel cut outs, worth every penny.
#11
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
You're right. This was probably a better question for people who own and use this wheel
#12
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I use a silca super pista to inflate mine. Best rebulidable pump out there imo. We're talking about a legacy brand; I have one that's 40 years old handed down to me and still kicking! Either only takes a few actuations to get up to 120+ PSI.
Forget the zipp crack pipe. It sucks! You'll find it always blowing off the valve from the pressure if you don't awkwardly press the chuck down on the valve while inflating.
I personally use a hirame chuck for all my wheels with a locking mechanism that's slim and unintrusive enough to fit aero wheel cut outs, worth every penny.
Forget the zipp crack pipe. It sucks! You'll find it always blowing off the valve from the pressure if you don't awkwardly press the chuck down on the valve while inflating.
I personally use a hirame chuck for all my wheels with a locking mechanism that's slim and unintrusive enough to fit aero wheel cut outs, worth every penny.
#13
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
A few weeks ago.
Timjohnson, if it's tight clearances that you're working with, try a Leyzne floor pump. They have a minimalist screw-on presta valve.
Timjohnson, if it's tight clearances that you're working with, try a Leyzne floor pump. They have a minimalist screw-on presta valve.
#14
Member
Join Date: Sep 2011
Posts: 27
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Topeak has a thread-on style crack-pipe that may help - https://www.topeak.com/products/Pumps/Pressure-Rite
#16
THE STUFFED
Join Date: Oct 2009
Location: San Francisco, CA
Posts: 12,671
Bikes: R. Sachs Road; EAI Bareknuckle; S-Works Enduro
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 361 Post(s)
Likes: 0
Liked 20 Times
in
17 Posts
Topeak has a thread-on style crack-pipe that may help - https://www.topeak.com/products/Pumps/Pressure-Rite
#17
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#18
Member
Join Date: Mar 2011
Posts: 41
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Just squeeze a rag in the valve arch, over the crack pipe and voilą.
#19
Pirate/Smuggler
try a Leyzne floor pump. They have a minimalist screw-on presta valve.
#20
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
+1, with one caveat: the screw-on chuck contains a fancy "ABS" mechanism that allows you to bleed the hose pressure before unscrewing it. To get this to work at 100psi or above you'll have to bleed the tire a bit *before* screwing on the chuck. Otherwise you'll be putting a couple hundred pounds of pressure into the hose and none into the tire. Once you get that routine settled in, the Lezyne is a great pump. Same goes for the hand models.
#21
Senior Member
plus my serfas fp-606. it's dual stage or whatever so i can pump with one hand really easily.
https://www.realcyclist.com/serfas-fp...age-floor-pump
#22
Member
Join Date: Sep 2011
Posts: 27
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I tested the lezyne today. It was a pain to scew on because I could not get my finger around the stem. Once the valve head is on there is no room for anything else in the cut out which basically means I either have to hold it in place or have it screwed on by just a few threads before it becomes impossible to thread. Lezyne does offer a slip chuck which is their 90degree adapter for disc wheels. I'm going to experiment with this at rei tomorrow and hopefully be done with this issue.
It looks like the two best options are still Silica adaptor + a friend, or a Hirame chuck. It might be $80, but it probably saves $80 worth of hassle over the lifetime of a disc wheel.
#23
Member
Thread Starter
Join Date: Feb 2013
Posts: 46
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I tried the Topeak JoeBlow X.O. over the weekend. It has a screw on fitting that I couldn't get to seal and was a huge pain.
It looks like the two best options are still Silica adaptor + a friend, or a Hirame chuck. It might be $80, but it probably saves $80 worth of hassle over the lifetime of a disc wheel.
It looks like the two best options are still Silica adaptor + a friend, or a Hirame chuck. It might be $80, but it probably saves $80 worth of hassle over the lifetime of a disc wheel.
I ended up going with the lezyne. Most of their models now come with a "slip chuck" which is their 90 degree adapter for disc wheels. Unfortunately I had to hold it on the stem while I pumped with one arm. I was able to get up to 105 psi though, which works for me. I wish i would have have went with the silca due to its rebuild factor but I didn't feel like ordering online. Maybe if this thing ever breaks...
#24
Senior Member
Join Date: Sep 2006
Location: Gnv, FL
Posts: 1,890
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I tried to like the Silca Pista floor pump we got at the shop but couldn't get into it. The wooden threads in the handle wallowed out and the piston lost most of its seal about as quick as any other floor pump in heavy shop use. When a typical floor pump is no longer able to get good compression I have found that the culprit leaking rubber o-rings on the piston head can be salvaged by removing them, stretching them a good bit by pulling on them with your fingers, and then reinstalling them with some Finish Line Wet lube, or similarly viscous lube. Hopefully this trick will save someone money and frustration.
#25
THE STUFFED
Join Date: Oct 2009
Location: San Francisco, CA
Posts: 12,671
Bikes: R. Sachs Road; EAI Bareknuckle; S-Works Enduro
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 361 Post(s)
Likes: 0
Liked 20 Times
in
17 Posts
I tried to like the Silca Pista floor pump we got at the shop but couldn't get into it. The wooden threads in the handle wallowed out and the piston lost most of its seal about as quick as any other floor pump in heavy shop use. When a typical floor pump is no longer able to get good compression I have found that the culprit leaking rubber o-rings on the piston head can be salvaged by removing them, stretching them a good bit by pulling on them with your fingers, and then reinstalling them with some Finish Line Wet lube, or similarly viscous lube. Hopefully this trick will save someone money and frustration.