Go Back  Bike Forums > Bike Forums > Singlespeed & Fixed Gear
Reload this Page >

Loosening chainring bolts

Notices
Singlespeed & Fixed Gear "I still feel that variable gears are only for people over forty-five. Isn't it better to triumph by the strength of your muscles than by the artifice of a derailer? We are getting soft...As for me, give me a fixed gear!"-- Henri Desgrange (31 January 1865 - 16 August 1940)

Loosening chainring bolts

Old 03-21-05, 11:39 AM
  #1  
Senior Member
Thread Starter
 
DKfix's Avatar
 
Join Date: Jan 2005
Location: N.Y. State (for now)
Posts: 102

Bikes: 1 Fix,2 SSs-more to come

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Are loosening chainring bolts just a byproduct of fixie riding or am I just using cheap *****e?
DKfix is offline  
Old 03-21-05, 11:42 AM
  #2  
cxmagazine dot com
 
pitboss's Avatar
 
Join Date: Jun 2003
Location: WI
Posts: 8,269

Bikes: Titus road, Fort CX

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
hmm...I haven't had this problem, but I have Sugino 75s and the bolts come with the arms, and are seated fairly well. I have heard of some people super-gluing these to make sure they don't loosen, but you can also try loctite (red? that is the 'weakest' if I remember) to aid in keeping them fastened tightly.
pitboss is offline  
Old 03-21-05, 11:48 AM
  #3  
Get the stick.
 
darkmother's Avatar
 
Join Date: Nov 2004
Location: Toronto, ON
Posts: 1,543

Bikes: 12 Y.O. Litespeed MTB, IRO Jamie Roy fixie, Custom Habanero Ti 'Cross, No name SS MTB, Old school lugged steel track bike (soon)

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
I find this happens on all my bikes where I run one ring on a double crank. Loctite works, as does nail polish on the threads. Also, I take a worn out chain ring, and cut it up, using the bolt hole sections as washers on the other (unused) side of the crank. Seems to work every time.
darkmother is offline  
Old 03-21-05, 11:49 AM
  #4  
auk
Coasting makes you grumpy
 
Join Date: Oct 2003
Location: Indiana
Posts: 1,376

Bikes: Specialized Stumpjumper M2Comp; Habanero Ti-Team; Slingshot Road; 1962 converted Raliegh fixer aka: The Beast

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Red is near the strongest and will require heat to aid in loosening the bolts. Better to go with the blue version as it will be a bit easier to get them out but will still be near-permanent as far as unwanted loosening.
auk is offline  
Old 03-21-05, 11:52 AM
  #5  
Senior Member
Thread Starter
 
DKfix's Avatar
 
Join Date: Jan 2005
Location: N.Y. State (for now)
Posts: 102

Bikes: 1 Fix,2 SSs-more to come

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I'm using cheapo BMX bolts. Are there better ones I could use? When I go to tighten these I notice a little sprinkle of metal dust falling. DAMN I hope that's not from the chainring!
DKfix is offline  
Old 03-21-05, 12:57 PM
  #6  
...
 
Hungry Joe's Avatar
 
Join Date: Mar 2005
Location: PGH
Posts: 12
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had that problem for a while but I think it was because of the holes in the chainring were worn and no longer round. So check that out. Loctite sounds like a good suggestion too. And the metal dust is most likely from the bolt threads getting stripped - make sure you're screwing them in straight.
Hungry Joe is offline  
Old 03-21-05, 02:07 PM
  #7  
Rebel Thousandaire
 
Ya Tu Sabes's Avatar
 
Join Date: Sep 2004
Location: Hartford, CT
Posts: 733

Bikes: Public D8, Yuba Mundo (cargo), Novara Buzz (1-speed, soon to be 2-speed w/ a kickback hub), Xootr 1-speed folder

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Are you using that special tool to hold the nut in place (the one with the two little tabs)? That helps a lot to really crank those suckers down properly. Darkmother's suggestion of making washers also works (especially if you're not using single stack c.r. bolts), but there is an easier solution, which I have employed from time to time: Buy five washers at the hardware store, which should run you about $2.
Ya Tu Sabes is offline  
Old 03-21-05, 03:43 PM
  #8  
biff-o-matic
 
biff's Avatar
 
Join Date: Nov 2003
Location: Austin, TX
Posts: 305

Bikes: Moyer Cycles #1 - A fixie of course.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Don't locktite - grease 'em up.

Seriously - grease the threads on the nuts and bolts, and grease the holes. It will hold tighter and you'll never have to re-tighten.
biff is offline  
Old 03-21-05, 04:59 PM
  #9  
Retrogrouch in Training
 
bostontrevor's Avatar
 
Join Date: Sep 2004
Location: Knee-deep in the day-to-day
Posts: 5,484
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
If properly tightened (using the stack bolt tool YTS mentioned), you shouldn't need any thread locker. Grease is good, it helps you to get the threads started properly as well as seating them with nice uniform tension that won't randomly give out.

The shavings really sound like you're cross-threading.
bostontrevor is offline  
Old 03-21-05, 05:23 PM
  #10  
Senior Member
Thread Starter
 
DKfix's Avatar
 
Join Date: Jan 2005
Location: N.Y. State (for now)
Posts: 102

Bikes: 1 Fix,2 SSs-more to come

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
OK I'll try the grease. I was told by a local bike wizard that I should use aluminum bolts instead of steel. So I'll give that a try as well.
DKfix is offline  
Old 03-22-05, 07:42 AM
  #11  
biff-o-matic
 
biff's Avatar
 
Join Date: Nov 2003
Location: Austin, TX
Posts: 305

Bikes: Moyer Cycles #1 - A fixie of course.

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
my aluminum bolts broke in about a month. plus, they're super expensive.

i just stick with the 5 dollar single speed ones.
biff is offline  
Old 03-22-05, 09:14 AM
  #12  
Senior Member
Thread Starter
 
DKfix's Avatar
 
Join Date: Jan 2005
Location: N.Y. State (for now)
Posts: 102

Bikes: 1 Fix,2 SSs-more to come

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Originally Posted by biff
my aluminum bolts broke in about a month. plus, they're super expensive.

i just stick with the 5 dollar single speed ones.
Ya know,when he said aluminum that was the first thing that went through my head. I can't see them being anywhere near as strong as steal.
DKfix is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.