Is re-gearing necessary
#1
coffee and slippers...
Thread Starter
Join Date: Aug 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Is re-gearing necessary
Hey all. I have an '07 Fuji Touring bike and am going on my first couple loaded tours this summer. I've seen a a few posts recommending re-gearing bikes even lower, but is this necessary? And if it is, what is your gearing? Thanks
#3
Senior Member
Join Date: Jun 2006
Location: Boston Area
Posts: 1,998
Bikes: Univega Gran Turismo, Guerciotti, Bridgestone MB2, Bike Friday New World Tourist, Serotta Ti
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
What gears you like is one of the ultimate YMMV issues. For touring I wouldn't want a low any higher than about 22 inches. I'd prefer to have something below 20 inches.
There are plenty of people who tour with higher gears, and I think one poster on BF has gears that go down to a 14 inch low.
Speedo
There are plenty of people who tour with higher gears, and I think one poster on BF has gears that go down to a 14 inch low.
Speedo
#4
Professional Fuss-Budget
FWIW I don't think you need to go too crazy; I've done some pretty intense hills with a low of 27 gear inches. I don't see much point in gearing that is so low that it's at walking speed. Depends in part on your fitness and on total weight as well.
#5
Senior Member
Join Date: Aug 2005
Posts: 3,872
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 598 Post(s)
Liked 283 Times
in
194 Posts
It depends almost entirely on where you will be touring, how mountainous and what the grades are like. Some hills in the east are actually worse than the west. You might be just fine with what you have.
#6
coffee and slippers...
Thread Starter
Join Date: Aug 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The current, stock gearing on my bike is 30-42-52 for the crankset and 11-32 for the cassette. I'm going to be touring over Mt. Hood pass on my first tour, and on my second tour I'll be going from here (Oregon) to Montana and down through Yellowstone.
#7
ah.... sure.
Join Date: Mar 2008
Location: Whidbey Island WA
Posts: 4,107
Bikes: Specialized.... schwinn..... enough to fill my needs..
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
if that is the case.. it sure wouldn't hurt swapping out the 30 for a 26. the cassette isn't going to help much going to a 34 but the ring sure will.
#8
Senior Member
Join Date: Mar 2007
Location: Saskatchewan
Posts: 2,465
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 6 Times
in
5 Posts
Not only is it totally inadequate for a loaded bike in the prairie wind it will really suck on a long mountain upgrade.
Re-gearing will give you more options in the middle, not just the low (which your present crank does not have anyway). A 52/42/30 is nice for a road bike, but why these are coming on touring bikes is beyond me.
In the "olde" days of my youth all the touring bikes had at least a 26 inner ring.
Think of it this way. When was the last time you were in the 52-11. Or even close to it with any amount of weight on the bike?
#9
coffee and slippers...
Thread Starter
Join Date: Aug 2008
Posts: 16
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks for the replies guys.
I've seen suggestions for a 50-38-26 cassette floating around the internet. Do you guys agree with that?
Also, how much does this usually cost to do at a shop?
I've seen suggestions for a 50-38-26 cassette floating around the internet. Do you guys agree with that?
Also, how much does this usually cost to do at a shop?
#10
Erect member since 1953
Join Date: Dec 2006
Location: Antioch, CA (SF Bay Area)
Posts: 7,000
Bikes: Trek 520 Grando, Roubaix Expert, Motobecane Ti Century Elite turned commuter, Some old French thing gone fixie
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 121 Post(s)
Likes: 0
Liked 38 Times
in
21 Posts
52-11 is a big gear even for a road bike! Compact crank set ups are only 50-11.
I've thought about this bike, but I have to factor in the price of a new set of chainrings.
I wonder what they are thinking? I mean, it's billed as a touring bike that comes with a rack....
I've thought about this bike, but I have to factor in the price of a new set of chainrings.
I wonder what they are thinking? I mean, it's billed as a touring bike that comes with a rack....
#11
Biker
Join Date: Jul 2008
Location: New Mexico
Posts: 264
Bikes: Boone McReynolds, Centurion Pro Tour
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 49 Post(s)
Liked 109 Times
in
61 Posts
Go to Sheldon Brown's gear chart and look at your possibilities for gearing. Its good advice to sacrifice some top end (won't use that big chain ring much) and make sure you can get down for the grunt up the hill (Previous posts have made good calls). tom
#12
Senior Member
Join Date: Mar 2007
Location: Saskatchewan
Posts: 2,465
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 6 Times
in
5 Posts
I selected this gearing as I live on the prairies. But it will have some shortcomings in the mountains.
I have to balance my touring and commuting needs as I use the bike for both.
#13
Senior Member
I have to agree with the posters above -- something like 48-36-26 (or close) is the right idea. Your bike will be happier overall; it's not just getting a "lower low," you'll also find yourself using more gears instead of just ignoring the big ring for all but downhills.
As for cost -- the labor to swap out cranksets, etc., should be pretty reasonable - $25-30, I would think.
If you buy a new crankset, pay for installation, and sell the old one it's not that expensive to upgrade.
#14
Senior Member
I used a 26 on mine and did the TA without a problem. A bit lower would have been nice in the Appalachians, but it was quite adequate in the Cascades and Rockies. Ideally, I would spend $80 or so on a Sugino XD600 crank (that is what I did), but just putting a 26 on the current crank is probably OK. A 24 might even be nice depending on your preferences.