Big Dummy racks DIY
#1
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
Big Dummy racks DIY
Well, after much procrastinating, and shifting project priorities, I finally got a start on making my Big Dummy useable.
Trying the DIY route, just to see how it turns out. 3/4" EMT conduit is the perfect size tubing for this, so here we go.
First, create a layout table, marking the angles and dimensions as found on Extracycle's open source documents.
Then, start bending the conduit, checking angles as you go.
Test fitting the tubes.
Zip tied two panniers on one side just to try it out for size.
So far so good.
Trying the DIY route, just to see how it turns out. 3/4" EMT conduit is the perfect size tubing for this, so here we go.
First, create a layout table, marking the angles and dimensions as found on Extracycle's open source documents.
Then, start bending the conduit, checking angles as you go.
Test fitting the tubes.
Zip tied two panniers on one side just to try it out for size.
So far so good.
Last edited by Dan Burkhart; 04-13-10 at 03:46 PM.
#2
Share the road.
I have wanted to try this. More progress pics will be eagerly anticipated.
#6
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
I think I'll call this a practice set, and make the next pair with a simple bend.
Last edited by Dan Burkhart; 07-09-10 at 10:34 PM.
#7
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
OK, I finally managed to grab a bit of time today to make up a second set. I gave up on the idea of trying to copy the profile of the factory originals, and came out with a much better result, and a matched pair.
To fit properly in the rear tube requires a small cutout to accommodate a small obstruction where two tubes join.
I'm much more satisfied with the result this time.
To fit properly in the rear tube requires a small cutout to accommodate a small obstruction where two tubes join.
I'm much more satisfied with the result this time.
Last edited by Dan Burkhart; 04-27-10 at 10:40 AM.
#11
Banned.
Join Date: Apr 2010
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Nice work Dan, much more better than the first one. When are you going to finished up with your whole work ? I am really excited to see what is the next thing you are going to do. I am also thinking to give a try like you but doesn't seems that I am good like you.
#12
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
As to when I'll finish, hard to say. Got a lot of other stuff going on right now but I'll work on it as I can.
#13
Senior Member
Join Date: Jan 2010
Location: Portland, OR
Posts: 698
Bikes: Leader 722TS, Surly Cross Check, GT Outpost, Haro Z16, Trek 1000
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
are you using steel or aluminum conduit?
#15
Share the road.
Are you going to make some wideloaders?
#16
Senior Member
Join Date: Apr 2010
Posts: 187
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Thanks. All it takes is a bit of patience,and the conduit is cheap, so screwing up the first try is not a disaster. The costliest part is the conduit bending tool, but you may be able to rent one at a rent-all store.
As to when I'll finish, hard to say. Got a lot of other stuff going on right now but I'll work on it as I can.
As to when I'll finish, hard to say. Got a lot of other stuff going on right now but I'll work on it as I can.
They look good.
#18
Jeff Foxworthy variety
Join Date: May 2008
Posts: 42
Bikes: Eight of them...
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I just ordered a Big Dummy frame to build up, and I had been planning on making my own rack system for it as well. It's good to see I'm not alone in my planning. That must make it a good idea! You're racks are very similar to what I was planning, and I'll be interested to see how yours turn out, as well as how mine come out as well. I'm planning on making mine able to work with panniers first, with bars built in to hang the panniers from and all, and eventually I may go so far as to custom make some larger bags similar to the Xtracycle setup. I was also going to do some wideloaders too, with runningboards on them. I've built racks for my regular bikes, and I usually top them off with a custom made wood deck with some sort of design burned in the top. The Dummy shall be no different.
Frame gets here later this week, and I can't wait!
Frame gets here later this week, and I can't wait!
#19
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
I just ordered a Big Dummy frame to build up, and I had been planning on making my own rack system for it as well. It's good to see I'm not alone in my planning. That must make it a good idea! You're racks are very similar to what I was planning, and I'll be interested to see how yours turn out, as well as how mine come out as well. I'm planning on making mine able to work with panniers first, with bars built in to hang the panniers from and all, and eventually I may go so far as to custom make some larger bags similar to the Xtracycle setup. I was also going to do some wideloaders too, with runningboards on them. I've built racks for my regular bikes, and I usually top them off with a custom made wood deck with some sort of design burned in the top. The Dummy shall be no different.
Frame gets here later this week, and I can't wait!
Frame gets here later this week, and I can't wait!
I'll try to grab some time to make a bit of progress this week.
#20
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
A little bit of progress today. I got My Eco Deck and Magic Carpet.
My frame spreading tool came in handy in the fitting stage,
The Magic Carpet is too small to fit over the Eco Deck.
I've got a workaround up my sleeve for that one though.
I got the stem and handlebar fitted to the seatpost. I'm going to trim the length some. It's kinda wide for little arms.
I managed to get started on the wide loaders, but ran out of time. Hope to finish em up tomorrow, at least the bending stage. The wood deck will take a bit longer.
I took my son in law for a ride on the back, and it handled it with no problem. If it can haul a 200 lb man, a 5 and 3 year old should be able to ride it together.
Hoping I can try it with all 3 of my grandkids this weekend.
My frame spreading tool came in handy in the fitting stage,
The Magic Carpet is too small to fit over the Eco Deck.
I've got a workaround up my sleeve for that one though.
I got the stem and handlebar fitted to the seatpost. I'm going to trim the length some. It's kinda wide for little arms.
I managed to get started on the wide loaders, but ran out of time. Hope to finish em up tomorrow, at least the bending stage. The wood deck will take a bit longer.
I took my son in law for a ride on the back, and it handled it with no problem. If it can haul a 200 lb man, a 5 and 3 year old should be able to ride it together.
Hoping I can try it with all 3 of my grandkids this weekend.
#21
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
Wide loaders with a twist. Step one.
Step two.
I think I'm going to narrow it down a bit though. I think this is going to be a bit wide.
Step two.
I think I'm going to narrow it down a bit though. I think this is going to be a bit wide.
#22
Share the road.
This is getting interesting. I think you have keep it no wider than a normal sidewalk or doorway. My Dummy fits through my door with the wideloaders on.
#23
Senior member
Thread Starter
Join Date: Oct 2004
Location: Oakville Ontario
Posts: 8,118
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 943 Post(s)
Liked 658 Times
in
371 Posts
Also, I think I came up against the limitations of the conduit bender here. I think a tubing bender capable of a tighter radius bend would do a better job for the upright bends.
Can anyone tell me what a fully assembled wide loader kit measures for width?
#24
Senior Member
there is a bender for 3/4 emt that makes a 4" radius bend. (well, just a hair over: NEC says > 4", so they're about 4 1/16".). That's about as tight a bend as is possible cold.
#25
Share the road.
I measured my Wideloader assemblied on my Dummy:
Rear is 25 1/2 inches
Front is 31 inches
Keep in mind I used a tape measure without a square.
Rear is 25 1/2 inches
Front is 31 inches
Keep in mind I used a tape measure without a square.