- First frame repair
- How to measure the rake of a fork
- Mixte Lug-sets for sale
- Deraileur tab position
- Some basics (stupid questions)
- Seat Stay and Drop out repair
- Oregon Handmade Bicycle Show
- filing lugs / shaving off parts
- Books on framebuilding/frame geometry
- How bad is this seatpost crack and what can be done? (Columbus Thermachrom steel)
- Frame Jig
- Minor Frame Repiar
- Non-round Seat Tube
- Bamboo question..
- Baked bamboo smells good.
- fastmetal
- Is this material appropriate
- cracks in head tube of Electra Aluminum frame
- Advised to re-post this in here:
- Looking for a special seatbinder... help
- Building my own frame
- Have I gone insane?
- Opinions about Serotta Classique and Lynskey Sportive
- Oxy-Acetylene Torch compatibility with Bernzomatic Oxy-Max Power Propylene cylinders
- Metallurgy 6061 vs 7005?? Pros and Cons of these 2 Frames on sale Thanks
- Is my frame seriously damaged?
- Looking for input... again.
- Mountain bike head tube
- Drilling holes in a frame
- Building a recumbent kit
- Double top tube cures shimmy?
- Silver prices
- Torches...
- Best way to remove brake cable mounts?
- Bruni - 26" Wheels
- Did I screw up by reheating dropout too many times??? Help
- What torch?
- Alternatives to paint/powder? Gun bluing?
- "Space-frame" bikes
- Cost of adding braze-ons/bosses
- rear suspension for VOTEC M6 frame
- Do I need reinforcements for h20 bosses?
- Halp!
- frame building help needed please.
- Front end impact damage looking for advice
- New bike leans to right with no hands on bar
- Filing out front fork-end
- Finally bit the bullet
- Titanium Forks
- Bike size
- Headset bearing loads
- New Steel for Bicycle Frames?
- A tour of Folk Engineered frame builders in Newark, NJ, Sunday, June 12, 2011 (fb)
- Filing lugs, 30 years after assembly
- Can I use stay-brite for small braze ons?
- Frances Bikes
- Seatpost + Bottle mount dilemma
- A few new touring builds
- Pre braze tube deflection
- 1 inch conduit bender to bend frok stays??
- Dimensions of downtubes on step through frames
- JB Weld Strong Enough for Braze-ons?
- Double canti post?
- Powder coat - metallic brown or metallic green??
- Stainless Steel frame?
- Would a local auto body shop do frame powdercoating?
- Bottom Bracket Fixturing
- Is this dropout joint going to fail?
- How to polish Ti.
- Rear drop out to have a Bob attachment AND Rohloff rear hub??
- Can this fork be fixed?
- How To Tell If a Frqame Is a Good Frame?
- Beware of the Desperado
- Mitsugi fork crowns availability?
- Monostay seat tube join
- A variation on a pedal
- frame make over
- copper bike?
- Columbus SPS track tubeset - $100
- Touring frame design help
- Road Bike Geometries
- Odd Tange Tubing Decal
- Welding Scandium
- Fork Crown / steertube failure
- 1999 Fat Chance Yo Eddy Correct Axle To Crown Length
- Should I change frame design because of wheel availability? A 650b quandry.
- The Feel of Steel
- Hope anybody could explain me this...
- Where is the market heading?
- A recumbent electric bike?
- Oxy-propane with a Smith AW1A?? any experience?
- Rans gets credit for inventing Crank Forward Bikes
- Felt Bikes
- Is this dent worth repairing?
- Magnesium frame over titanium?
- Ultra-light supercustom
- franken-tandem
- Rear Derailleur Cable Stop Position
- Where are the Front End Geometry Questions asked?
- are brake bosses sold individually?