Floor pumps?
#51
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
As you noted, a high volume pump will struggle to reach high pressure and you may not weigh enough to depress the plunger as the pressure gets high enough.
#52
Senior Member
Join Date: Jun 2013
Location: Bozeman
Posts: 4,094
Bikes: 199? Landshark Roadshark, 198? Mondonico Diamond, 1987 Panasonic DX-5000, 1987 Bianchi Limited, Univega... Chrome..., 1989 Schwinn Woodlands, Motobecane USA Record, Raleigh Tokul 2
Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 1131 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
The Lezyne Sport Floor Drive or Joe Blow Sport are both okay floor pumps. I'm not a fan of either pump's chuck. I use a Silca presta chuck on my Lezyne rather than their hokey screw on chuck. It looks like the new (to me) ABS2 works well on presta but seems fiddly on schrader.
The chuck on the Joe Blow is a bit confusing because I can never figure out which way the lever on that kind of chuck should be pushed. It always seems backward to me.
-snip-
The chuck on the Joe Blow is a bit confusing because I can never figure out which way the lever on that kind of chuck should be pushed. It always seems backward to me.
-snip-
The Joe Blow (about the same price as the park pumps) seems to be a hell of a lot nicer construction. It's mostly metal, which is nice, compared to the mostly plastic park pump. And the head isn't too bad. For ours you just lift the lever in the opposite direction of the valve (so the lever always gets lifted AWAY from the tire.) I found it more annoying to use than the park head, but with better results.
The lezyne, on the other hand, is built very well. All metal (except the fancy "wooden" handle). I actually like the chuck on the lezyne. It took me about a week to get used to it. It's... fancy and you actually need to learn how to do it. There are different operating instructions for both presta and schrader. (Presta you pull the "ring" back, then push it on the valve, the push the ring forward, then screw it a turn or so. Super secure attachment. Then just pull the ring back at the same time as you're pulling the chuck off to remove it. For schrader, you push the ring forward and basically just screw it on.)
With that said, I used a wal-mart schwinn branded pump for 3 years before it "failed" on me.
#53
It's MY mountain
Join Date: Sep 2006
Location: Mt.Diablo
Posts: 10,002
Bikes: Klein, Merckx, Trek
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
Quoted: 4337 Post(s)
Liked 2,980 Times
in
1,617 Posts
#54
A little North of Hell
Join Date: Mar 2006
Posts: 4,892
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 71 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts
Rennkompressor
I'm surprised I've only seen it mentioned once, but I'm not surprised it has been mentioned.
SKS Rennkompressor. I never had a good floor pump until I bought this one almost ten years ago, and I really haven't given it much thought since. I figure if it works so well I forget about it, it's the most I can ask of a bike pump.
Steel, wood, high pressure. German. $60.
SKS Rennkompressor. I never had a good floor pump until I bought this one almost ten years ago, and I really haven't given it much thought since. I figure if it works so well I forget about it, it's the most I can ask of a bike pump.
Steel, wood, high pressure. German. $60.
#55
Senior Member
Join Date: Apr 2009
Location: Boulder County, CO
Posts: 1,511
Bikes: '92 22" Cannondale M2000, '92 Cannondale R1000 Tandem, another modern Canndondale tandem, Two Holy Grail '86 Cannondale ST800s 27" (68.5cm) Touring bike w/Superbe Pro components and Phil Wood hubs. A bunch of other 27" ST frames & bikes.
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 110 Post(s)
Likes: 0
Liked 4 Times
in
4 Posts