Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Torch a 531 frame?

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Torch a 531 frame?

Old 05-20-17, 10:44 AM
  #1  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Torch a 531 frame?

I recently picked up a ladies Falcon Westminster. Without looking harder the date codes on both hubs, Maillard, indicate 1987. Happy 30th. The frame is butted 531 and the forks are 531. The paintwork is plagued with rust but none of it looks structurally bad. Previously on 18-23 frames I have been quite happy to burn the paint off with a meaty Blow Torch prior to a respray but AFAIK 531 undergoes some sort of heat treatment. I might be worrying too much but if I do go and Torch it am I likely to mess with the properties of the steel?
chorlton is offline  
Old 05-20-17, 11:09 AM
  #2  
Senior Member
 
FBOATSB's Avatar
 
Join Date: Jul 2014
Location: Central Indiana
Posts: 2,201

Bikes: Old Stuff

Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
Quoted: 912 Post(s)
Liked 514 Times in 343 Posts
I would reccomend chemical stripping in this case. My opinion only, of course.
FBOATSB is offline  
Old 05-20-17, 11:16 AM
  #3  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
Media blasting is done with softer material like ground walnut shells. (than Sand)
fietsbob is offline  
Old 05-20-17, 12:09 PM
  #4  
Senior Member
 
Join Date: Feb 2009
Posts: 6,660
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 582 Post(s)
Liked 171 Times in 138 Posts
Keep it below 1200 degrees. Better yet if there is a machine shop in your area they may have a sand blasting booth for this job.
davidad is offline  
Old 05-20-17, 12:16 PM
  #5  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
@FBOATSB If in doubt probably does apply. I did use paint stripper, Tetrion, on the first bike I refurbished. Hours if not Days of fun getting into all the nooks and crannies.

@fietsbob That would be good if I had the equipment to hand. Otherwise I would have to outsource and at that stage may as well get it powder coated. The bike cost £12 and I can burn and rattle can it for £15, primer, colour and clearcoat. Miss out the burn and add paint stripper for a total of £20. Obviously I am going to overspend in order to bring it back to life but...
Attached Images
File Type: jpg
DSCF5843.jpg (96.1 KB, 226 views)
File Type: jpg
DSCF5845.jpg (92.8 KB, 227 views)
File Type: jpg
DSCF5846.jpg (97.3 KB, 226 views)
chorlton is offline  
Old 05-20-17, 12:38 PM
  #6  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by davidad
Keep it below 1200 degrees. Better yet if there is a machine shop in your area they may have a sand blasting booth for this job.

1200°F -> 650°C which sounds like brazing temperature? I do not expect to hit that in terms of burning off paint.

Reynolds Technology

Perhaps I should ask.
chorlton is offline  
Old 05-20-17, 12:45 PM
  #7  
Old fart
 
JohnDThompson's Avatar
 
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,935

Bikes: Several, mostly not name brands.

Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3571 Post(s)
Liked 3,367 Times in 1,916 Posts
I'd be more concerned about toxic fumes from the burning paint than the heat adversely affecting the steel. What's wrong with media blasting?
JohnDThompson is offline  
Old 05-20-17, 01:13 PM
  #8  
afraid of whales
 
Mr IGH's Avatar
 
Join Date: Apr 2009
Location: Front Range, CO
Posts: 4,306
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 347 Post(s)
Likes: 0
Liked 5 Times in 5 Posts
I've never seen paint really clean up enough for paint prep with a torch. I think you'll end up sanding/blasting anyway. I always use a powerful chemical stripper, ZipStrip. I use it in an open garage when the temp is above 70*F and give it time to work. I use a wire brush to remove the stripper/paint, takes me a few hours to remove all the paint completely.

Here's what I always see after torching the paint, this is silver solder brazing temp, lots of burned paint hanging on real tight:
Attached Images
File Type: jpg
DT cable stops.jpg (83.7 KB, 217 views)
Mr IGH is offline  
Old 05-20-17, 01:28 PM
  #9  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by JohnDThompson
I'd be more concerned about toxic fumes from the burning paint than the heat adversely affecting the steel. What's wrong with media blasting?
Nothing apart from the possible cost. Looking locally...

Home Page

It's not Apples and Pears but guess at £15-£30 then add on transport costs and I still have to paint it. £30 is new spokes, rim tape and inner tubes.

Point taken about toxicity. Ignoring the environment I burn at arms length and stand up wind.
chorlton is offline  
Old 05-20-17, 01:54 PM
  #10  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by Mr IGH
I've never seen paint really clean up enough for paint prep with a torch. I think you'll end up sanding/blasting anyway. I always use a powerful chemical stripper, ZipStrip. I use it in an open garage when the temp is above 70*F and give it time to work. I use a wire brush to remove the stripper/paint, takes me a few hours to remove all the paint completely.

Here's what I always see after torching the paint, this is silver solder brazing temp, lots of burned paint hanging on real tight:
Understood. However you were not really trying to burn the paint off. That was just collateral damage. If you set out to purposely burn paint off it goes through about three stages. Melts, Blackens, turns to Ash. Much of the ash drops off without provocation and the remainder gives up when attacked with a Dish Cloth soaked in White Spirit.

Some fettling is still required but apart from that it takes about 30 minutes to burn it down to bare steel.
chorlton is offline  
Old 05-20-17, 05:33 PM
  #11  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 18,003

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4172 Post(s)
Liked 3,791 Times in 2,270 Posts
I would not have a non bike experienced shop do any sand blasting on a nice lightweight steel frame. It is very east to remove significant wall thickness if the blaster dwells in one spot for too long. A lot of fab shops are not experienced with thin wall/gage products and often let their least costly (as in youngest usually) employee do the dirty work with little supervision. I would leave the sand blasting to the painter, they know about this stuff.


I would suggest using chemical methods to remove as much of the paint as possible first. This is far less harmful to the steel and reduced the amount of sand blasting done later. It is rather bad for one's brain, skin and eyes if you don't take proper precautions.


I have also burned off paint but the results still need further sanding or blasting. It can be real bad for the brain. I don't suggest it. Andy
Andrew R Stewart is offline  
Old 05-20-17, 06:24 PM
  #12  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
531 is not heat treated so, within reason burning off the paint won't change it's properties. Reynolds made a heat treated premium version of 531 known as 753 and it did have to be protected from excess heat. Reynolds spec'ed silver brazing for it to keep the temperature exposure within it's limits.
HillRider is offline  
Old 05-20-17, 06:51 PM
  #13  
Senior Member
 
Join Date: Apr 2009
Location: Boulder County, CO
Posts: 1,513

Bikes: '92 22" Cannondale M2000, '92 Cannondale R1000 Tandem, another modern Canndondale tandem, Two Holy Grail '86 Cannondale ST800s 27" (68.5cm) Touring bike w/Superbe Pro components and Phil Wood hubs. A bunch of other 27" ST frames & bikes.

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 110 Post(s)
Likes: 0
Liked 4 Times in 4 Posts
Originally Posted by FBOATSB
I would reccomend chemical stripping in this case. My opinion only, of course.
No. It's steel sandblast it.
mtnbke is offline  
Old 05-20-17, 08:26 PM
  #14  
Insane Bicycle Mechanic
 
Jeff Wills's Avatar
 
Join Date: Mar 2008
Location: other Vancouver
Posts: 9,811
Mentioned: 34 Post(s)
Tagged: 0 Thread(s)
Quoted: 788 Post(s)
Liked 688 Times in 367 Posts
I would talk to an automotive machine shop. They often have chemical "hot tanks" for removing grease from large automotive parts. A few minutes in there will dissolve any paint without damaging the tubing.
__________________
Jeff Wills

Comcast nuked my web page. It will return soon..
Jeff Wills is offline  
Old 05-20-17, 11:29 PM
  #15  
Senior Member
 
Join Date: Apr 2009
Location: Boulder County, CO
Posts: 1,513

Bikes: '92 22" Cannondale M2000, '92 Cannondale R1000 Tandem, another modern Canndondale tandem, Two Holy Grail '86 Cannondale ST800s 27" (68.5cm) Touring bike w/Superbe Pro components and Phil Wood hubs. A bunch of other 27" ST frames & bikes.

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 110 Post(s)
Likes: 0
Liked 4 Times in 4 Posts
It takes a lot longer than two minutes to dissolve paint.
mtnbke is offline  
Old 05-21-17, 05:03 AM
  #16  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Thanks for the replies. It looks like I am going to be investing in a bottle of goop, rubber gloves and brillo pads. Rather than asking Reynolds via the web form I've done so via an e-mail to what appears to be their technical support. If the request gets lost in the system I'll phone them. If I do get a response I'll add it to the thread.... Now I have to pick a colour. Stick to something close to the original or something off the wall. Decisions Decisions.
chorlton is offline  
Old 05-21-17, 12:03 PM
  #17  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
TI Reynolds is a Tube mill they really don't interact with end users, bicycle owners..

just factories and companies selling frame making parts to custom frame builder's shops..





.....
fietsbob is offline  
Old 05-21-17, 12:31 PM
  #18  
IFG
Junior Member
 
Join Date: Aug 2009
Posts: 17
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I had success with paint stripper years ago.
IFG is offline  
Old 05-21-17, 12:35 PM
  #19  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by fietsbob
TI Reynolds is a Tube mill they really don't interact with end users, bicycle owners..

just factories and companies selling frame making parts to custom frame builder's shops..

.....
I live in hope but that's fairly powerful unless PR is low on the list. Assuming things do not go to plan can I quote you?
chorlton is offline  
Old 05-21-17, 12:49 PM
  #20  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
Bicycle shops are the closest service entry to the customer , the manufacturer is the furthest..

Generally the best customer service flows back up stream thru the bike shop.

Now if you want an 8x8x20 foot maritime container or truck full .

then you are the size of buyer manufacturers are usually shipping to ,
that is a distributor's niche, pallets full of cases on shelves in warehouses.



...
fietsbob is offline  
Old 05-22-17, 03:20 AM
  #21  
Full Member
Thread Starter
 
Join Date: Oct 2016
Posts: 277
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 98 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Originally Posted by fietsbob
TI Reynolds is a Tube mill they really don't interact with end users, bicycle owners..

just factories and companies selling frame making parts to custom frame builder's shops..

.....
Response from Reynolds... Sorry if it is a bit small.

Thank you very much for getting in touch.

The tempering temperature of 531 is around 520°C so there is a small risk when stripping pain this way.

My personal recommendation would always be to media blast rather than torch. However, provided you keep the temperatures low and you don’t hold the torch there for very long. I wouldn’t expect you to run into any issues.

I hope this helps. Please do let me know if you have any other questions.

All the best,
Attached Images
chorlton is offline  
Old 05-22-17, 04:09 AM
  #22  
Senior Member
 
Join Date: Jun 2003
Posts: 16,771
Mentioned: 125 Post(s)
Tagged: 0 Thread(s)
Quoted: 1454 Post(s)
Liked 85 Times in 40 Posts
Too many risks with flame and heat. You probably still need to invest in a pair of stout real leather gloves to protect yourself. Plus a respirator for the fumes.

For the frames I have stripped, I have always used paint stripper. Yeah, a bit more work, and there are still fumes to consider, but I would rather take the extra time than spend it in hospital with respiratory issues from burnt paint.

There are places that dip strip larger items such as window frames and furniture. I don't know if they exist around you, but it might be worth considering. You do have to ensure the inside of the frame is well washed out.
Rowan is offline  
Old 05-22-17, 05:49 AM
  #23  
Senior Member
 
Join Date: Apr 2014
Posts: 193

Bikes: Giant Cypress DX

Mentioned: 25 Post(s)
Tagged: 0 Thread(s)
Quoted: 246 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Is paint removal with a torch considered typical in the bike world? My first thought when stripping paint is chemically with paint stripper. Aircraft paint stripper works great on cars. The gung-ho restorer's way is to have the car dipped in a chemical bath.
Robert P is offline  
Old 05-22-17, 07:01 AM
  #24  
Senior Member
 
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656

Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!

Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times in 741 Posts
Originally Posted by Robert P
Is paint removal with a torch considered typical in the bike world?
No, it's not. Therefore all of the above posts recommending against it.
HillRider is offline  
Old 05-22-17, 07:06 AM
  #25  
Senior Member
 
Join Date: Dec 2010
Location: Above ground, Walnut Creek, Ca
Posts: 6,681

Bikes: 8 ss bikes, 1 5-speed touring bike

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 86 Post(s)
Likes: 0
Liked 4 Times in 4 Posts
Originally Posted by chorlton
Response from Reynolds... Sorry if it is a bit small.

[/FONT][/COLOR]
impressive!

i can't even get my stock broker to reply to my emails.
hueyhoolihan is offline  

Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.