Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Disk brake wheel - repetitive removal / mounting

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Disk brake wheel - repetitive removal / mounting

Old 04-28-20, 02:24 PM
  #1  
Redbullet
Full Member
Thread Starter
 
Join Date: Aug 2015
Posts: 485
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 207 Post(s)
Liked 27 Times in 22 Posts
Disk brake wheel - repetitive mounting / dismounting

Hi,
I have a question about road bikes with disk brakes (I use rim brakes for the moment): How do disk brakes behave in case of repetitive mounting / dismounting of the front wheel, for transportation inside the car? Do they need special care and adjustments each time, or are they as simple to mount / dismount, as rim brakes?

Thanks
Redbullet is offline  
Old 04-28-20, 07:20 PM
  #2  
davidad
Senior Member
 
Join Date: Feb 2009
Posts: 6,622
Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 558 Post(s)
Liked 159 Times in 128 Posts
as long as you are careful there should be no problems. The disc is thin and it can be easily bent if not handled properly.
davidad is offline  
Old 04-28-20, 08:24 PM
  #3  
JanMM
rebmeM roineS
 
JanMM's Avatar
 
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,180

Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 644 Post(s)
Liked 328 Times in 213 Posts
Never a problem with the one bike I own with a front disc brake and which must have the front wheel removed to carry the bike on a roof rack.
__________________
Bacchetta Giro A20, RANS V-Rex, RANS Screamer
JanMM is offline  
Old 04-28-20, 08:35 PM
  #4  
trailangel
Senior Member
 
trailangel's Avatar
 
Join Date: Feb 2014
Location: Pasadena, CA
Posts: 4,791

Bikes: Schwinn Varsity

Mentioned: 22 Post(s)
Tagged: 0 Thread(s)
Quoted: 1890 Post(s)
Liked 667 Times in 390 Posts
This is why you get a frame with thru axles. Lines up the same way every time.
trailangel is offline  
Old 04-29-20, 04:47 AM
  #5  
dsaul
Senior Member
 
Join Date: Jan 2013
Location: South Jersey
Posts: 2,146
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
Quoted: 668 Post(s)
Liked 653 Times in 402 Posts
Just be careful not to pull the brake lever with the wheel out and it will be fine.
dsaul is offline  
Old 04-29-20, 06:24 AM
  #6  
ted_major
Junior Member
 
ted_major's Avatar
 
Join Date: Oct 2008
Location: Tuscaloosa, Ala.
Posts: 134
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 31 Times in 18 Posts
Originally Posted by trailangel View Post
This is why you get a frame with thru axles. Lines up the same way every time.
Thatís been my experience. I have one bike with discs and quick releases, and I think maybe once Iíve been able to reinstall the front wheel without the brake rubbing. Just about every time the wheel comes off, I have to re-align the caliper.

The bike with thru-axles? The caliper lines up with the disc perfectly every time. I donít plan on having another bike with both discs and QRs.
ted_major is offline  
Likes For ted_major:
Old 04-29-20, 11:06 AM
  #7  
Retro Grouch 
Senior Member
 
Retro Grouch's Avatar
 
Join Date: Feb 2004
Location: St Peters, Missouri
Posts: 30,225

Bikes: Catrike 559 I own some others but they don't get ridden very much.

Mentioned: 16 Post(s)
Tagged: 0 Thread(s)
Quoted: 1570 Post(s)
Liked 637 Times in 358 Posts
Originally Posted by ted_major View Post
Thatís been my experience. I have one bike with discs and quick releases, and I think maybe once Iíve been able to reinstall the front wheel without the brake rubbing. Just about every time the wheel comes off, I have to re-align the caliper.

The bike with thru-axles? The caliper lines up with the disc perfectly every time. I donít plan on having another bike with both discs and QRs.
If you flip your bike over when replacing the wheel, try this trick insted:
Hold the bike upright while you thread the disc onto the brake caliper and the axle into the fork ends. Set the bike down until the axle bottoms in the fork ends, tighten the QR and you'll be good to go.
__________________
My greatest fear is all of my kids standing around my coffin and talking about "how sensible" dad was.
Retro Grouch is offline  
Old 04-29-20, 11:34 AM
  #8  
JanMM
rebmeM roineS
 
JanMM's Avatar
 
Join Date: Jan 2006
Location: Metro Indy, IN
Posts: 16,180

Bikes: Bacchetta Giro A20, RANS V-Rex, RANS Screamer

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 644 Post(s)
Liked 328 Times in 213 Posts
Originally Posted by dsaul View Post
Just be careful not to pull the brake lever with the wheel out and it will be fine.
Good advice for hydraulic brakes.
__________________
Bacchetta Giro A20, RANS V-Rex, RANS Screamer
JanMM is offline  
Old 04-29-20, 12:32 PM
  #9  
Olefeller77 
Senior Member
 
Join Date: Sep 2019
Location: Illinois quad cities (Colona)
Posts: 194

Bikes: Trek Marlin 6 29r - Scattanti road bike w carbon fork - Trek 6500 - Univega Alpina 503 - Specialized Sworks M4 made in USA

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 90 Post(s)
Liked 103 Times in 57 Posts
I do lots of one way riding then enjoy lunch with the wife. I remove the front wheel and roll the bike in the back of the mini van. Never an issue with the hyd brakes.
Olefeller77 is offline  
Old 04-29-20, 12:39 PM
  #10  
ted_major
Junior Member
 
ted_major's Avatar
 
Join Date: Oct 2008
Location: Tuscaloosa, Ala.
Posts: 134
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 31 Times in 18 Posts
Originally Posted by Retro Grouch View Post
Set the bike down until the axle bottoms in the fork ends, tighten the QR and you'll be good to go.
I do that, but the caliper still rubs almost every time I reinstall the front wheel. Iíve gone through several sets of calipers, all of which behaved the same way. The bike in question is a 2016 GT Grade, which came w/ TRP HY-RD brakes (and Shimano 105 brifters). I went through a couple of pairs of those under warranty because it was impossible to adjust them so that they wouldnít bottom out on the handlebars. TRP eventually sent me a pair of Spyre calipers, which worked w/o bottoming out, but like the HY-RDs needed re-aligning every time I took the front wheel off. Those were eventually replaced with Yokozuna Motokos, which worked great, but still required caliper re-alignment.

My best guess as to the root cause is that I use Nitto Randonneur bars, which have a traditional round bend instead of modern ergo bars that angle backwards in a straight line. I suspect an ergo bar would leave room for more lever travel, so that I have to adjust the pads close to the disc (which gives me a nice, firm lever feel) and there just isnít any room for even the tiniest misalignment without caliper rub.
ted_major is offline  
Old 04-29-20, 12:49 PM
  #11  
DorkDisk
Senior Member
 
Join Date: May 2013
Location: Kips Bay, NY
Posts: 2,096

Bikes: Ritchey Swiss Cross | Teesdale Kona Hot | Haro Extreme | Specialized Stumpjumper Comp | Cannondale F1000 | Shogun 1000 | Cannondale M500 | Norco Charger | Marin Muirwoods 29er | Shogun Kaze | Breezer Lightning

Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
Quoted: 531 Post(s)
Liked 817 Times in 423 Posts
Originally Posted by ted_major View Post
I do that, but the caliper still rubs almost every time I reinstall the front wheel. Iíve gone through several sets of calipers, all of which behaved the same way. The bike in question is a 2016 GT Grade, which came w/ TRP HY-RD brakes (and Shimano 105 brifters). I went through a couple of pairs of those under warranty because it was impossible to adjust them so that they wouldnít bottom out on the handlebars. TRP eventually sent me a pair of Spyre calipers, which worked w/o bottoming out, but like the HY-RDs needed re-aligning every time I took the front wheel off. Those were eventually replaced with Yokozuna Motokos, which worked great, but still required caliper re-alignment.

My best guess as to the root cause is that I use Nitto Randonneur bars, which have a traditional round bend instead of modern ergo bars that angle backwards in a straight line. I suspect an ergo bar would leave room for more lever travel, so that I have to adjust the pads close to the disc (which gives me a nice, firm lever feel) and there just isnít any room for even the tiniest misalignment without caliper rub.
On QRs, the lawyer tabs are to blame. Since one has to turn the skewer a few times to remove and install the wheel, different tensions are placed each time which throw the alignment out of wack. I've had good luck counting revolutions (usually 4 or 5) when removing the wheel and tightening the same amount of revolutions.
DorkDisk is offline  
Old 04-29-20, 01:39 PM
  #12  
ted_major
Junior Member
 
ted_major's Avatar
 
Join Date: Oct 2008
Location: Tuscaloosa, Ala.
Posts: 134
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 37 Post(s)
Liked 31 Times in 18 Posts
Originally Posted by DorkDisk View Post
I've had good luck counting revolutions (usually 4 or 5) when removing the wheel and tightening the same amount of revolutions.
I do that too (it takes 4 revolutions for this bike). Still canít get the disc & caliper to stay aligned. Mostly I just donít take the wheels off.
ted_major is offline  
Old 04-29-20, 01:46 PM
  #13  
Bigbus
Very Senior Member
 
Join Date: Mar 2018
Location: Always on the Run
Posts: 1,211

Bikes: Giant Quasar & Fuji Roubaix

Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quoted: 413 Post(s)
Liked 342 Times in 243 Posts
I've never not had to realign the caliper everytime I remove my front wheel for transport. It only takes a second to loosen the caliper, lightly squeeze the brake and retighten, but it's still a pain in the arse.
Bigbus is offline  
Old 04-29-20, 10:23 PM
  #14  
katsup
Senior Member
 
katsup's Avatar
 
Join Date: May 2016
Location: Southern California
Posts: 1,686

Bikes: 2008 Salsa El Mariachi, Cotic SolarisMax, Soma Fog Cutter

Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quoted: 579 Post(s)
Liked 489 Times in 283 Posts
Originally Posted by ted_major View Post
Thatís been my experience. I have one bike with discs and quick releases, and I think maybe once Iíve been able to reinstall the front wheel without the brake rubbing. Just about every time the wheel comes off, I have to re-align the caliper.

The bike with thru-axles? The caliper lines up with the disc perfectly every time. I donít plan on having another bike with both discs and QRs.
You can get some DT Swiss RWS skewers which are similar to thru axles. I never had much of a problem with normal QR skewers, maybe reseating the wheel once or twice. But a friend gave me some RWS skewers and I have yet to have a misalignment with them. These skewers are new to me though and I haven't taken the wheel off much since owning them.
katsup is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2022 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.