Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Creaking seat

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Creaking seat

Old 10-16-21, 09:43 AM
  #1  
pennpaul
Senior Member
Thread Starter
 
Join Date: Sep 2017
Location: Central America
Posts: 279

Bikes: Diamondback Haanjo Trail, Fuji Team Road

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 120 Post(s)
Liked 41 Times in 24 Posts
Creaking seat

I know it's been asked but there have been so many threads, I can't sift through all of them. My saddle is creaking after I finally got it dialed in just right, but I can't take the creaking. The saddle rails are CrMo. How do I fix this for good?

Thanks,
Paul
pennpaul is offline  
Old 10-16-21, 09:53 AM
  #2  
Chuckles1
Senior Member
 
Join Date: Oct 2019
Location: Foothills of West Central Maine
Posts: 365

Bikes: 2007 Motobecane Fantom Cross Expert, 2020 Motobecane Omni Strada Pro Disc (700c gravel bike), 2021 Motobecane Elite Adventure with Bafang 500W rear hub drive

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 152 Post(s)
Likes: 0
Liked 124 Times in 82 Posts
Are you sure it's the saddle and not the seapost creaking? I thought my bottom bracket was creaking, but it turned out that regreasing the seat post eliminated the annoying creak.
Chuckles1 is offline  
Likes For Chuckles1:
Old 10-16-21, 07:46 PM
  #3  
pennpaul
Senior Member
Thread Starter
 
Join Date: Sep 2017
Location: Central America
Posts: 279

Bikes: Diamondback Haanjo Trail, Fuji Team Road

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 120 Post(s)
Liked 41 Times in 24 Posts
Originally Posted by Chuckles1 View Post
Are you sure it's the saddle and not the seapost creaking? I thought my bottom bracket was creaking, but it turned out that regreasing the seat post eliminated the annoying creak.
Hmmm...good point, no. I guess I can ride around with a phone recording sound in both area to figure it out.

Really, though, grease the seatpost?
pennpaul is offline  
Old 10-16-21, 08:18 PM
  #4  
Andrew R Stewart 
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 15,413

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Raleigh Pro, Trek Cycle Cross, Mongoose tomac ATB, GT Bravado ATB, JCP Folder

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3085 Post(s)
Liked 1,508 Times in 1,027 Posts
The best final solution for this sort of stuff is a take apart, cleaning of contact surfaces and reassembly with grease, lubes, anti seize. The challenge is to avoid the thinking that your initial assumptions are what is going on. Any clamped or joining parts of a component can be the cause. Start with the easy stuff first but don't be surprised if you find that some other assembly is the source. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 10-16-21, 08:22 PM
  #5  
cxwrench
Senior Member
 
cxwrench's Avatar
 
Join Date: Jul 2013
Location: Nor-Cal
Posts: 2,339

Bikes: lots

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 1094 Post(s)
Liked 1,407 Times in 787 Posts
Clean and grease EVERYTHING...post in the frame, if it's a carbon frame and/or post use carbon paste. Clean and grease every bolt and place where parts touch. Saddle rails, post clamps...everything. Then make sure you get that **** tight.
cxwrench is offline  
Likes For cxwrench:
Old 10-17-21, 01:33 AM
  #6  
Lazyass
Senior Member
 
Join Date: Jul 2008
Location: Minas Ithil
Posts: 9,249
Mentioned: 63 Post(s)
Tagged: 0 Thread(s)
Quoted: 2382 Post(s)
Liked 560 Times in 346 Posts
Another possible issue with the seatpost is that it can creak if it goes down really far inside of the seat tube. My saddles are set a little lower than average and I've had a couple of really long posts that needed to be cut down a few inches to stop creaking.
Lazyass is offline  
Likes For Lazyass:
Old 10-17-21, 08:57 AM
  #7  
Chuckles1
Senior Member
 
Join Date: Oct 2019
Location: Foothills of West Central Maine
Posts: 365

Bikes: 2007 Motobecane Fantom Cross Expert, 2020 Motobecane Omni Strada Pro Disc (700c gravel bike), 2021 Motobecane Elite Adventure with Bafang 500W rear hub drive

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 152 Post(s)
Likes: 0
Liked 124 Times in 82 Posts
Originally Posted by pennpaul View Post
Really, though, grease the seatpost?
Yes, seat post should be greased if non-carbon frame. If not greased, it could seize and be difficult to remove or adjust in the future. The grease should be wiped off and renewed with fresh grease periodically, like when it starts creaking. Also note good advice from other respondents. I'll bet you a nickel it's the seat post creaking.
Chuckles1 is offline  
Likes For Chuckles1:
Old 10-17-21, 04:26 PM
  #8  
pennpaul
Senior Member
Thread Starter
 
Join Date: Sep 2017
Location: Central America
Posts: 279

Bikes: Diamondback Haanjo Trail, Fuji Team Road

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 120 Post(s)
Liked 41 Times in 24 Posts
Originally Posted by Chuckles1 View Post
I'll bet you a nickel it's the seat post creaking.
Where do I send the money? Some grease on the seatpost fixed it.

Thanks
Paul
pennpaul is offline  
Likes For pennpaul:
Old 10-17-21, 10:46 PM
  #9  
veganbikes
Clark W. Griswold
 
Join Date: Mar 2014
Location: ,location, location
Posts: 8,954

Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), Cilo Road Frame, Proteus frame, Ti 26 MTB

Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 2505 Post(s)
Liked 1,551 Times in 1,035 Posts
A good lesson folks, metal on metal contact does require grease or anti seize compounds and proper torque. You will be amazed at the noises you don't here when everything is put together correctly and you really don't need much and don't need to get super fancy a simple tube of grease (Phil Wood is my fave) or Anti Seize (Park's stuff is nice because it is silver and tends to match better with my ti bikes) and a good torque wrench (even an Park ATD-1 or CDI TorqControl would work). You can even buy tubs of grease or anti seize from automotive places pretty cheap if that is your jam. Also every once and a while especially on a well used bike pull components out and clean and re-grease to prevent any corrosion and check all of your parts and re-torque them. Never a bad idea and could save you down the line.
veganbikes is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.