What tool to use for cutting cable housings?
01-09-22, 12:40 PM
#51
Time Traveler
Thread Starter
If there arent there should be. I understand these Schwinns were made in the millions and still quite popular. I ordered a jagwire kit last night. I will have to use my new cutter to custom fit the cables. I still need the 4 mm metal housing caps though. They are like $40 for a lifetime supply. I think I need only 4 or 5. Alternately I read on another board that microwashers can be used to keep the linear wire strands from being forced into the hole where the cable goes. Another way is to use the cables from the kit but use 5mm coil type brake cable instead as I have some scraps from a department store parts bike. It does fit in the stays, shifters and derailers.
Last edited by BikePower; 01-09-22 at 12:48 PM.
01-09-22, 06:46 PM
#52
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,744
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 571 Post(s)
Liked 918 Times
in
473 Posts
There aren’t, it was sarcasm. Sorry!
Tim
Tim
01-09-22, 07:14 PM
#53
SE Wis
Join Date: Apr 2005
Location: Milwaukee, WI
Posts: 9,824
Bikes: '68 Raleigh Sprite, '02 Raleigh C500, '84 Raleigh Gran Prix, '91 Trek 400, 2013 Novara Randonee, 1990 Trek 970
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2446 Post(s)
Liked 2,814 Times
in
1,722 Posts
But there are for certain old Raleighs. The original brake & shift cables were double ended. You had to get the proper length one for your frame
https://www.ebay.com/itm/31258001019...cAAMXQ3kNTi13b
https://www.ebay.com/itm/31254258581...oAAMXQDnpTXWr2
https://www.ebay.com/itm/31258001019...cAAMXQ3kNTi13b
https://www.ebay.com/itm/31254258581...oAAMXQDnpTXWr2
01-09-22, 08:18 PM
#54
Senior Member
Join Date: Dec 2015
Location: Menomonee Falls, WI
Posts: 1,744
Bikes: 1984 Schwinn Supersport, 1988 Trek 400T, 1977 Trek TX900, 1982 Bianchi Champione del Mondo, 1978 Raleigh Supercourse, 1986 Trek 400 Elance, 1991 Waterford PDG OS Paramount, 1971 Schwinn Sports Tourer, 1985 Trek 670
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 571 Post(s)
Liked 918 Times
in
473 Posts
@dedhead, you are correct sir, but there are none for a 72 Schwinn Continental, in spite of the number they produced.
Tim
Tim
01-09-22, 09:39 PM
#55
Senior Member
No. It does NOT make perfect cuts, but it is still better than any Home Depot cutter I have ever used. The cable-through-the-housing trick always works for me, though.
01-09-22, 10:04 PM
#56
Time Traveler
Thread Starter
I got my park cutter and tried it out. It cuts ok without a cable in it but if I put a scrap cable in there its darn near perfect. Im going to try putting a solid copper wire in there next time I cut as suggested to me in this forum. I think that would be ideal.
Likes For BikePower:
01-10-22, 06:41 AM
#57
Senior Member
Cool! I'm glad you found a solution.
01-13-22, 08:27 AM
#58
Senior Member
Join Date: Nov 2014
Location: Saratoga calif.
Posts: 959
Bikes: Miyata 610(66cm), GT Vantara Hybrid (64cm), Nishiki International (64cm), Peugeot rat rod (62 cm), Trek 800 Burning Man helicopter bike, Bob Jackson frame (to be restored?) plus a never ending stream of neglected waifs from the Bike exchange.
Mentioned: 19 Post(s)
Tagged: 0 Thread(s)
Quoted: 315 Post(s)
Likes: 0
Liked 412 Times
in
167 Posts
For years I used a pair of side cutters to cut cable and housing. I finally bought a Park cn 10 and now wonder why I didn't do it years ago. When cutting spiral housing I poke a scratch awl into the end to make sure it is open, Often the spiral wrap wire obstructs the end of the cable after cutting. Not a problem with straight wrap brake cable.
01-13-22, 11:04 AM
#59
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1956 Post(s)
Liked 2,929 Times
in
1,488 Posts
For years I used a pair of side cutters to cut cable and housing. I finally bought a Park cn 10 and now wonder why I didn't do it years ago. When cutting spiral housing I poke a scratch awl into the end to make sure it is open, Often the spiral wrap wire obstructs the end of the cable after cutting. Not a problem with straight wrap brake cable.
01-13-22, 03:41 PM
#60
Full Member
For cable ends I don't like crimps. It's permanent and you can only cut it once or maybe twice before it's too short unless you leave a lot of excess to begin with. I use heat shrink. The best is with hot glue layer already in but a dab off a hotglue stick and regular heatshrink is fine too. Looks cleaner than crimps IMO and is easily removable.
01-14-22, 06:29 PM
#61
Senior Member
I can’t really imagine why anyone that does any kind of home workshop tinkering (including bike stuff) wouldn’t have a Dremel-type rotary tool🤔. The original Dremel tool is the “gold standard” but there are lots of knock offs out there. Harbor Freight, Menards, Home Depot to name a few. Mine is actually a Craftsman but looks to me to be an exact Dremel copy (perhaps even made by Dremel). The knock offs prolly even cost less than the brand name manual cutters. Using a rotary tool with a cut off wheel, IMHO, makes a perfect cut especially on the spiral wound brake cable housings (but also on the linear shifter cable housings!)
