Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Best Carbon Assembly Paste/Compound for Carbon to aluminum

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Best Carbon Assembly Paste/Compound for Carbon to aluminum

Old 06-23-22, 03:38 PM
  #1  
Plainsman
Senior Member
Thread Starter
 
Join Date: Jan 2005
Posts: 1,451
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 147 Post(s)
Liked 30 Times in 22 Posts
Best Carbon Assembly Paste/Compound for Carbon to aluminum

Hi! Iím trying to find a good assembly option for a carbon seat post in an aluminum frame that wonít scratch the carbon post. I have pretty immediate access to the following, but open to other options:

Finish Line Fiber Grip
Motorex Carbon Grease
Park Tool SAC-2
Muc Off Carbon Gripper

is one of these better than the others in terms of holding strength, protecting the carbon from bonding to aluminum, and not harming the carbon finish?

Thanks in advance!
Plainsman is offline  
Old 06-23-22, 04:37 PM
  #2  
Crankycrank
Senior Member
 
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,026
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
Quoted: 640 Post(s)
Liked 607 Times in 461 Posts
I think any CF paste will likely leave minor dulling at the least. Any of those above will have little to no difference in corrosion protection or scratching between them. Any scratching/dulling can usually be buffed out with most plastic/paint polishes though if you decide to raise your post at some point. You can always just use grease first and go to the paste if you have slipping.
Crankycrank is offline  
Old 06-23-22, 04:46 PM
  #3  
dsbrantjr
Senior Member
 
dsbrantjr's Avatar
 
Join Date: Sep 2010
Location: Roswell, GA
Posts: 8,253

Bikes: '93 Trek 750, '92 Schwinn Crisscross, '93 Mongoose Alta

Mentioned: 29 Post(s)
Tagged: 0 Thread(s)
Quoted: 1414 Post(s)
Liked 1,004 Times in 680 Posts
I make all of my controls "race tight", tight enough to stay put under normal stresses, but still able to move/rotate during a spill/crash, hopefully minimizing damage and injuries.
dsbrantjr is offline  
Old 06-23-22, 04:47 PM
  #4  
SoSmellyAir
Method to My Madness
 
Join Date: Nov 2020
Location: Orange County, California
Posts: 1,796

Bikes: Cannondale Synapse, Cannondale CAAD4, Trek FX 2

Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
Quoted: 865 Post(s)
Liked 548 Times in 421 Posts
I used Finish Line Fiber Grip to install my matte finish CF seat post (Cannondale Save) a few years ago. A couple of weeks ago I decided to raise it by a quarter inch, and first removed it to wipe off as much of the residue as possible. The Finish Line Fiber Grip did not affect the finish of the seat post. But the seat tube is also CF and the hidden seat post clamp within it is either CF or plastic. No aluminum interface.

Last edited by SoSmellyAir; 06-23-22 at 04:51 PM.
SoSmellyAir is online now  
Likes For SoSmellyAir:
Old 06-24-22, 05:52 AM
  #5  
Sy Reene
Advocatus Diaboli
 
Sy Reene's Avatar
 
Join Date: Feb 2015
Location: Wherever I am
Posts: 7,902

Bikes: Merlin Cyrene, Nashbar steel CX

Mentioned: 12 Post(s)
Tagged: 1 Thread(s)
Quoted: 4248 Post(s)
Liked 1,218 Times in 801 Posts
Originally Posted by Crankycrank View Post
I think any CF paste will likely leave minor dulling at the least. Any of those above will have little to no difference in corrosion protection or scratching between them. Any scratching/dulling can usually be buffed out with most plastic/paint polishes though if you decide to raise your post at some point. You can always just use grease first and go to the paste if you have slipping.
+1 this
I use the SAC2 park stuff because that's what I happened to buy a few years ago. No avoiding marring to some extent -- I have a CF post in a Ti frame, but same idea. Also use this stuff on stem/handlebar clamp interface.

Suggest though you figure out your seatpost height before doing any CF paste. Then do a few wraps of eg. electrical tape or somesuch at that point on the seatpost. This will at least prevent going too far and then having to back in/out of the seat tube while you get it right (which in itself can and will cause marring).
Sy Reene is offline  
Old 06-25-22, 02:52 PM
  #6  
KerryIrons
Full Member
 
Join Date: Mar 2012
Posts: 339
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 146 Post(s)
Likes: 0
Liked 164 Times in 96 Posts
Originally Posted by Plainsman View Post
Hi! Iím trying to find a good assembly option for a carbon seat post in an aluminum frame that wonít scratch the carbon post. I have pretty immediate access to the following, but open to other options:

Finish Line Fiber Grip
Motorex Carbon Grease
Park Tool SAC-2
Muc Off Carbon Gripper

is one of these better than the others in terms of holding strength, protecting the carbon from bonding to aluminum, and not harming the carbon finish?
CF paste is basically grease with grit in it. You only need it if things slip with normal grease and proper torque. Don't overthink this.
KerryIrons is offline  
Old 06-28-22, 12:31 AM
  #7  
Camilo
Senior Member
 
Join Date: Apr 2007
Posts: 5,626
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 633 Post(s)
Liked 492 Times in 327 Posts
FWIW, to address the OP's concern about dulling the finish of a CF seatpost. Dulling and superficial scratches can easily be removed and original shine restored with normal polishing products. I have a couple strengths of rubbing compound and normal car polish. Just rub out the scratches and polish. All can be done by hand in about 5 minutes.
Camilo is online now  
Old 06-28-22, 04:40 AM
  #8  
Sy Reene
Advocatus Diaboli
 
Sy Reene's Avatar
 
Join Date: Feb 2015
Location: Wherever I am
Posts: 7,902

Bikes: Merlin Cyrene, Nashbar steel CX

Mentioned: 12 Post(s)
Tagged: 1 Thread(s)
Quoted: 4248 Post(s)
Liked 1,218 Times in 801 Posts
Originally Posted by Camilo View Post
FWIW, to address the OP's concern about dulling the finish of a CF seatpost. Dulling and superficial scratches can easily be removed and original shine restored with normal polishing products. I have a couple strengths of rubbing compound and normal car polish. Just rub out the scratches and polish. All can be done by hand in about 5 minutes.
How does that work? I thought CF's natural state is a very matte appearance. If the clear coat gloss finish is scratched (off) will a polish restore areas to gloss?
Sy Reene is offline  
Old 06-28-22, 01:32 PM
  #9  
Camilo
Senior Member
 
Join Date: Apr 2007
Posts: 5,626
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 633 Post(s)
Liked 492 Times in 327 Posts
Originally Posted by Sy Reene View Post
How does that work? I thought CF's natural state is a very matte appearance. If the clear coat gloss finish is scratched (off) will a polish restore areas to gloss?
Probably yes, if the clear coat is totally rubbed off. Usually, like a car, it's just dulled and/or often just superficially scratched, not removed. I guess all I can say with certainty is that I've shined up a few carbon fiber seat posts, at least the parts that show above the seat tube and sometimes the entire post. The result might not be "factory fresh" but easily passes the "3 foot" (1 meter) test - looks great from normal viewing distance.
Camilo is online now  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.