Bike Forums

Bike Forums (https://www.bikeforums.net/forum.php)
-   Bicycle Mechanics (https://www.bikeforums.net/bicycle-mechanics/)
-   -   Crown race fit question (https://www.bikeforums.net/bicycle-mechanics/1254626-crown-race-fit-question.html)

hhk25 07-05-22 06:54 AM

Crown race fit question
 
I changed forks on a bike recently and on the new fork, the crown race (from the old fork) slipped into place on the steerer tube without much effort. In other words, I pushed it down by hand instead of using the crown race setting tool. There didn't appear to be any perceptible movement in the race but I'm wondering if I should be concerned about this. Every other crown race I've installed was a tight fight and had to be tapped down using the tool.

Maybe I'm worried about nothing and the compression from the top cap will tighten up the race? Or should I be looking to replace the race?

bboy314 07-05-22 07:49 AM

Are the forks both milled for the same size crown race? If it’s a 1” steer tube, you might be switching from a 27mm to 26.4mm race seat, in which case I’d replace the crown race with the proper size. Or if it’s a 1 1/8” steer tube, is the new crown race the split type? These are made to slide on without a tool.

HillRider 07-05-22 08:05 AM

Was the fit of the crown race on the new steerer a modestly firm push fit or sloppy fit? If it took a reasonably firm push you should be fine. If it was a 27.0 race on a 26.4 steerer the fit would be noticeably sloppy. As to a split crown race, the OP just transferred the old race to the new fork so that isn't the issue unless the old race was already a split type.

hhk25 07-05-22 08:18 AM

Using digital calipers, the old fork is 30.08mm. The new fork (I have a second uninstalled, identical fork) measures about the same. Give or take .02mm. I’m assuming any difference is just error created by how hard I push the calipers jaws.

I think I’m okay. What’s the worst that can happen? Damage the race and bearings?

Andrew R Stewart 07-05-22 08:20 AM

I suspect (from what the OP says) that both forks were machined for the same crown race diameter fit but the replacement fork was cut a tad too small. (This is not uncommon with hand driven machining).

Two options are dimpling the crown race diameter with a center punch in a number of spots around the steerer and/or using a retaining compound (LockTite 609 or equivalent). Andy

hhk25 07-05-22 09:17 AM


Originally Posted by HillRider (Post 22564215)
Was the fit of the crown race on the new steerer a modestly firm push fit or sloppy fit? If it took a reasonably firm push you should be fine. If it was a 27.0 race on a 26.4 steerer the fit would be noticeably sloppy. As to a split crown race, the OP just transferred the old race to the new fork so that isn't the issue unless the old race was already a split type.

Modestly firm and the race was not the split type.

JohnDThompson 07-07-22 07:05 AM

A bearing retaining compound, as Andrew suggests above, would work. E.g. Loctite #609. Stein makes a knurling tool to slightly increase the diameter of the race seat to fix this issue, as well. Probably not cost-effective for a one-off job, but perhaps a local shop may already have one and do the work for you?

https://steintool.com/wp-content/upl...nurl_Step1.jpg
https://steintool.com/portfolio-items/knurling-tool/

Crankycrank 07-07-22 08:02 AM

Check with the headset mfr. I know Chris King sold slightly undersized races for their HS but you had to contact them directly to get the info. and possibly the same for other mfrs.


All times are GMT -6. The time now is 02:34 AM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.