derailleur hanger keeps going out of true
09-12-22, 05:50 PM
#1
Full Member
Thread Starter
Join Date: Jul 2006
Posts: 446
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 9 Post(s)
Likes: 0
Liked 3 Times
in
2 Posts
derailleur hanger keeps going out of true
I have a CAAD10 with 6870 di2 (11 speed) and the derailleur hanger keeps going out of true. The rear derailleur will graze the spokes of my back wheel - very worrisome.
I could replace the derailleur hanger, is there anything else I should look for?
Thanks.
I could replace the derailleur hanger, is there anything else I should look for?
Thanks.
09-12-22, 08:36 PM
#2
Senior Member
Join Date: Jul 2005
Location: Boulder County, CO
Posts: 3,926
Bikes: '80 Masi Gran Criterium, '12 Trek Madone, early '60s Frejus track
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
Quoted: 351 Post(s)
Liked 285 Times
in
215 Posts
If the hanger has been hit and straightened too many times, it will go soft. Or it could be that the last adjustment just wasn't right. I don't have the bike in front of me so you'll have to figure this out yourself.
If you need a new hanger, go to derailleurhanger.com and look up your bike. Here, I did it for you. https://derailleurhanger.com/manufac...series2011-16/
Even brand new hangers sometimes require small tweaks to align properly, so check this before mounting and adjusting the derailleur.
If you need a new hanger, go to derailleurhanger.com and look up your bike. Here, I did it for you. https://derailleurhanger.com/manufac...series2011-16/
Even brand new hangers sometimes require small tweaks to align properly, so check this before mounting and adjusting the derailleur.
Likes For oldbobcat:
09-12-22, 08:37 PM
#3
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 36,942
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 132 Post(s)
Tagged: 1 Thread(s)
Quoted: 4888 Post(s)
Liked 939 Times
in
561 Posts
It's absolutely critical that the hanger is properly pocketed into the frame. Poor support at that interface allows the hanger to move when the QR is tightened.
Of course it might be as simple as your bad habit of dropping the bike on the right side, or otherwise bumping onto the derailleur.
Of course it might be as simple as your bad habit of dropping the bike on the right side, or otherwise bumping onto the derailleur.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
“Never argue with an idiot. He will only bring you down to his level and beat you with experience.”, George Carlin
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
“Never argue with an idiot. He will only bring you down to his level and beat you with experience.”, George Carlin
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Likes For FBinNY:
09-12-22, 10:09 PM
#4
Clark W. Griswold
Join Date: Mar 2014
Location: ,location, location
Posts: 11,432
Bikes: Foundry Chilkoot Ti W/Ultegra Di2, Salsa Timberjack Ti, Cinelli Mash Work RandoCross Fun Time Machine, 1x9 XT Parts Hybrid, Co-Motion Cascadia, Specialized Langster, Phil Wood Apple VeloXS Frame (w/DA 7400), R+M Supercharger2 Rohloff, Habanero Ti 26
Mentioned: 48 Post(s)
Tagged: 0 Thread(s)
Quoted: 3533 Post(s)
Liked 2,857 Times
in
1,915 Posts
Not knowing the history of the old hanger I would say replace it and get a new hanger from Wheels Manufacturing and make sure you are using a proper hanger alignment tool. Abbey, Efficient Velo Tools, Shimano, Park Tool make excellent quality ones but make sure you know how to use it properly always use the same point on your wheel so you can be accurate. Also I would check that your derailleur isn't damaged if it is routinely hitting the spokes that can also bend things and throw it out of alignment which can cause greater headaches. Also important to make sure your limit screws are properly set.
When installing a new hanger make sure it is properly lubricated or thread locked per manufacturer directions and it is also properly torqued and make sure it is aligned to the frame as it might be perfectly "true" but your frame might not bend it could need some light adjustment to get it set up for your frame.
When installing a new hanger make sure it is properly lubricated or thread locked per manufacturer directions and it is also properly torqued and make sure it is aligned to the frame as it might be perfectly "true" but your frame might not bend it could need some light adjustment to get it set up for your frame.
Likes For veganbikes:
09-13-22, 08:09 AM
#5
Senior Member
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,241
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 712 Post(s)
Liked 745 Times
in
550 Posts
Also make sure when you replace the wheel that it's inserted all the way into the dropouts when the quick release is clamped so it doesn't sit differently each time.
Likes For Crankycrank:
09-13-22, 01:53 PM
#6
Senior Member
Join Date: Jul 2013
Location: Nor-Cal
Posts: 3,767
Bikes: lots
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
Quoted: 1954 Post(s)
Liked 2,925 Times
in
1,488 Posts
Originally Posted by Crankycrank
Also make sure when you replace the wheel that it's inserted all the way into the dropouts when the quick release is clamped so it doesn't sit differently each time.
Likes For cxwrench:
09-14-22, 09:31 AM
#7
Senior Member
Join Date: May 2004
Location: Southern California
Posts: 2,164
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 103 Post(s)
Liked 103 Times
in
81 Posts
Originally Posted by Crankycrank
Also make sure when you replace the wheel that it's inserted all the way into the dropouts when the quick release is clamped so it doesn't sit differently each time.
Likes For MudPie:
