Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Fork steerer and bottom headset issue - vintage

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Fork steerer and bottom headset issue - vintage

Old 09-26-23, 02:50 PM
  #1  
Veteran, Pacifist
Thread Starter
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,025

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 280 Post(s)
Tagged: 0 Thread(s)
Quoted: 3734 Post(s)
Liked 4,348 Times in 2,033 Posts
Fork steerer and bottom headset issue - vintage

Need advice on a fork to headset concern, never experienced before.
Bike is an early '70s Holdsworth Pro with (supposedly) original fork, although the frame and fork serial numbers do not match.
The bottom headset race does not seat onto the fork steerer.
Picture worth 1,000 words. I gently filed the top of ridge to show it better in the pic.


The fork steerer has a 'ridge' where it joins the fork crown that prevents the headset from seating properly. The steerer (above the ridge) is 25.4mm and 26.4mm at the crown. Only a 1mm increase.

Have tried a '70s Campa headset and a new one but neither seat onto the fork crown.

What to do?
Wildwood is offline  
Old 09-26-23, 03:24 PM
  #2  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,686

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4026 Post(s)
Liked 3,444 Times in 2,092 Posts
The "ridge" is the fork crown race seat. It should have been both machined round to a 26.5mm diameter (allowing for a 0.1mm interference fit with the headset's race) and it's face/bottom flat/perpendicular by someone before the initial assembly. The .1mm interference fit will want a significant impact force to drive the race onto the seat. Best done with a tool which will evenly contact the race and slide on the fork's steerer, maybe extending above the top of the steerer which will let a hammer be used to create the impact. These tools resemble a length of pipe/tube with a fairly thick wall. Sometimes the amount of impact force is similar to driving a 10P nail into a chunk of hard wood.

What tool was used to try to install your race?

There are times when the race seat is not well machined or became ring notched by poor install/removal of a previous race (if the race cocks crooked a lot). Then a re-machining of the fork's seat is the good choice. Can this be done by a home "mechanic"? Sort of, but not with out care and skill with a hand file on the mechanic's side. These days few of us have had that kind of exposure to working to close dimensions with simple hand tools and if done poorly the race can end up sitting loosely and this is not good or right. I strongly suggest enlisting a shop (or well equipped home guy) to do this kind of work if at all possible.

As to the serial numbers not matching this is not uncommon for some factories back then. Frames and forks were often made in batches separate of each other and only combined when the F&F are painted. I have seen this with Holdsworthy and other English brands before. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 09-26-23, 03:37 PM
  #3  
Veteran, Pacifist
Thread Starter
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,025

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 280 Post(s)
Tagged: 0 Thread(s)
Quoted: 3734 Post(s)
Liked 4,348 Times in 2,033 Posts
Thanks @Andrew R Stewart
Have only fit them on loosely with no tools or hammering involved.

Serial number difference not a concern, but another Holdsworthy has matching serial #s, a 1980 model - so post bike boom.

I have assembled a number of framesets and never encountered the 'problem' to the extent of this one. Caution to get a correct fit and proper seat is understood and I will heed your advice.

Last edited by Wildwood; 09-26-23 at 03:48 PM.
Wildwood is offline  
Old 09-26-23, 03:56 PM
  #4  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,686

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4026 Post(s)
Liked 3,444 Times in 2,092 Posts
With more modern headset race and bearing designs the race is actually only a seat for the bearing cartridge, not also a ball track surface (as is with most "classic" loose ball designs). So the bearing seating ring could be either split or meant to fit onto a conical crown seat (so no interference fit). Really cheap "American" bikes sometimes have a very loose fitting crown race. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 09-26-23, 04:22 PM
  #5  
Senior Member
 
Join Date: Mar 2012
Posts: 876
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 457 Post(s)
Likes: 0
Liked 563 Times in 312 Posts
Originally Posted by Wildwood
Thanks [MENTION=391685]Have only fit them on loosely with no tools or hammering involved.
Conversely, I have never installed a crown race on a fork that didn't need to be "hammered" into place. That is why they make crown race setting tools. If your previous experience had the crown races just slipping on without force, you were dealing with poorly sized crown race seats on those forks.
KerryIrons is offline  
Likes For KerryIrons:
Old 09-26-23, 05:06 PM
  #6  
biked well
 
well biked's Avatar
 
Join Date: Jul 2005
Posts: 7,483
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 139 Post(s)
Liked 150 Times in 86 Posts
+1 to crown races being an interference fit onto the crown race seat, requiring tools to install and uninstall. A crown race that installs loosely, without tools, is a mismatch to the crown race seat, not the other way around.
well biked is offline  
Likes For well biked:
Old 09-26-23, 05:07 PM
  #7  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,686

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4026 Post(s)
Liked 3,444 Times in 2,092 Posts
Originally Posted by KerryIrons
Conversely, I have never installed a crown race on a fork that didn't need to be "hammered" into place. That is why they make crown race setting tools. If your previous experience had the crown races just slipping on without force, you were dealing with poorly sized crown race seats on those forks.
Or with a design that didn't use a press/interference fit for the crown race.

With no knowledge of what previous bikes the OP was working on we can't be sure those other examples needed to be hammered down tight. I am quite sure the headset for this Holdsworthy will be an interference fit though. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 09-26-23, 05:12 PM
  #8  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,686

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4026 Post(s)
Liked 3,444 Times in 2,092 Posts
Originally Posted by well biked
+1 to crown races being an interference fit onto the crown race seat, requiring tools to install and uninstall. A crown race that installs loosely, without tools, is a mismatch to the crown race seat, not the other way around.
Yet many 27.0 crown seats have been machined down to 26.4 (both are actually that .1mm larger, but that isn't a dimension listed in most all headset specs thus the race diameter spec being referenced) to allow for a replacement headset to work, for whatever reason why. Of course doing a non reversable procedure to a frame or fork is generally not one's first choice, sourcing the OEM spec headset is the better first choice. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Likes For Andrew R Stewart:
Old 09-26-23, 06:11 PM
  #9  
Senior Member
 
Join Date: Jan 2009
Location: San Diego, CA
Posts: 3,515
Mentioned: 10 Post(s)
Tagged: 0 Thread(s)
Quoted: 803 Post(s)
Liked 952 Times in 682 Posts
This is one of the rare tasks that I'll take to a bike shop. They will have a special reamer tool to make the race round and the correct size and usually install your bearing race for you at the same time. Bring the headset with you that you will be using. Not really a difficult job to install the race but the shop ensures the steerer is machined properly.

Last edited by Crankycrank; 09-27-23 at 07:37 AM.
Crankycrank is offline  
Old 09-26-23, 08:07 PM
  #10  
biked well
 
well biked's Avatar
 
Join Date: Jul 2005
Posts: 7,483
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 139 Post(s)
Liked 150 Times in 86 Posts
Originally Posted by Andrew R Stewart
Yet many 27.0 crown seats have been machined down to 26.4 (both are actually that .1mm larger, but that isn't a dimension listed in most all headset specs thus the race diameter spec being referenced) to allow for a replacement headset to work, for whatever reason why. Of course doing a non reversable procedure to a frame or fork is generally not one's first choice, sourcing the OEM spec headset is the better first choice. Andy
What I was trying to communicate to the OP was that, based on the two types of experiences reported with crown race installation, it's actually the crown races that required no tools and could be installed by hand that are the concern, not the crown race that fits too tightly to do that. As we've already covered, a properly fitting crown race should require a setting process, with tools, because of the interference fit. I probably didn't communicate that very well in my earlier post.
well biked is offline  
Old 09-27-23, 02:18 AM
  #11  
Senior Member
 
Join Date: Apr 2019
Location: UK
Posts: 569
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 265 Post(s)
Liked 153 Times in 119 Posts
My father-in-law raced these and what I can contribute is; its Holdsworth, not Holdsworthy

choddo is offline  
Old 09-27-23, 08:06 AM
  #12  
Senior Member
 
grumpus's Avatar
 
Join Date: Apr 2016
Posts: 748
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 283 Post(s)
Liked 244 Times in 193 Posts
Originally Posted by Wildwood
Need advice on a fork to headset concern, never experienced before.
Bike is an early '70s Holdsworth Pro with (supposedly)
Picture worth 1,000 words. I gently filed the top of ridge to show it better in the pic.


The fork steerer has a 'ridge' where it joins the fork crown that prevents the headset from seating properly. The steerer (above the ridge) is 25.4mm and 26.4mm at the crown. Only a 1mm increase.

Have tried a '70s Campa headset and a new one but neither seat onto the fork crown.

What to do?
Looks like your filing has destroyed the concentricity of the race seat, which should be a firm interference fit. You could try taking it to a bike shop that has the necessary cutting and facing tool to clean it up, but I suspect that will just show the seat is now undersized. This may be useable with the addition of bearing retainer compound, but otherwise it will need a frame builder to add some bronze and machine it back to spec.
grumpus is offline  
Old 09-27-23, 08:13 AM
  #13  
Veteran, Pacifist
Thread Starter
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,025

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 280 Post(s)
Tagged: 0 Thread(s)
Quoted: 3734 Post(s)
Liked 4,348 Times in 2,033 Posts
Thanks for all the input.
Wildwood is offline  
Old 09-27-23, 12:53 PM
  #14  
seor miembro
 
SurferRosa's Avatar
 
Join Date: Dec 2018
Location: Pac NW
Posts: 8,468

Bikes: '70s - '80s Campagnolo

Mentioned: 91 Post(s)
Tagged: 0 Thread(s)
Quoted: 3686 Post(s)
Liked 6,091 Times in 3,027 Posts
Originally Posted by Wildwood
The steerer is 25.4mm and 26.4mm at the crown.
Those are ISO/English values. A standard headset should work as long as the steerer is tall enough for the headset's stack height. I use a piece of 1" pvc pipe to install the crown race.
SurferRosa is online now  
Likes For SurferRosa:
Old 09-27-23, 02:06 PM
  #15  
Wheelman
 
Join Date: Aug 2021
Location: Putney, London UK
Posts: 686

Bikes: 1982 Holdsworth Avanti (531), 1961 Holdsworth Cyclone

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 224 Post(s)
Liked 547 Times in 274 Posts
I've got a couple of Holdsworths, both with original forks (matching numbers).
.
1961 Holdsworth Cyclone: crown race JIS 27.0mm, steerer diameter 25.4mm
1982 Holdsworth Avanti: crown race JIS 27.0mm, steerer diameter 25.4mm
.
Fitted Tange Levin CDS JIS to both.
They were both hammered on at the local bike shop after I failed to install the Avanti race - don't have the correct diameter tubing (to use as a hammer).
If you get the right bike shop they won't charge

Last edited by Aardwolf; 09-27-23 at 02:39 PM.
Aardwolf is offline  
Old 09-27-23, 04:16 PM
  #16  
Veteran, Pacifist
Thread Starter
 
Wildwood's Avatar
 
Join Date: Dec 2004
Location: Seattle area
Posts: 13,025

Bikes: Bikes??? Thought this was social media?!?

Mentioned: 280 Post(s)
Tagged: 0 Thread(s)
Quoted: 3734 Post(s)
Liked 4,348 Times in 2,033 Posts
I used pvc once and it worked. But this one is tighter than I have experienced previously. I'm gonna let a shop handle it, got several to contact. This frameset I have high expectations for (ie, why I inquired here to get it properly right) - early '70s, perfect fit, original paint, orange&panels, chrome fork+socks, 531, bit 'o history. What more can I say?! (At least my minor/light filing did no harm.)


edit: I have always been under the impression that my English manufactured for Irish Harding distribution were produced under contract to the Holdsworthy company, that also produced Clive Stewart frames and others.
W. F. Holdsworth (nkilgariff.com)
i stand corrected if wrong
something like this - which may have been owned, possibly raced, by an Irish team, bitd. So, not Holdsworth branded, ever.




re-edit: Apologies, forgot this isn't C&V! thanks again for the headset advices.

Last edited by Wildwood; 09-27-23 at 05:09 PM.
Wildwood is offline  
Likes For Wildwood:
Old 09-29-23, 07:52 AM
  #17  
Senior Member
 
Mr. 66's Avatar
 
Join Date: Aug 2015
Posts: 3,328
Mentioned: 38 Post(s)
Tagged: 0 Thread(s)
Quoted: 1079 Post(s)
Liked 1,572 Times in 890 Posts
For shop service I use Wright Bros., Charles is excellent, but note he is a cash only business these days.
Mr. 66 is offline  
Old 09-29-23, 08:13 AM
  #18  
Senior Member
 
Join Date: Dec 2020
Location: Wake Forest, NC
Posts: 4,852

Bikes: 1989 Cinelli Supercorsa

Mentioned: 11 Post(s)
Tagged: 0 Thread(s)
Quoted: 2890 Post(s)
Liked 2,444 Times in 1,472 Posts
Originally Posted by Wildwood
I used pvc once and it worked. But this one is tighter than I have experienced previously.
Which is why the shop tool is made of metal, and not plastic.
smd4 is offline  
Old 09-29-23, 09:32 PM
  #19  
Senior Member
 
Andrew R Stewart's Avatar
 
Join Date: Feb 2012
Location: Rochester, NY
Posts: 17,686

Bikes: Stewart S&S coupled sport tourer, Stewart Sunday light, Stewart Commuting, Stewart Touring, Co Motion Tandem, Stewart 3-Spd, Stewart Track, Fuji Finest, Mongoose Tomac ATB, GT Bravado ATB, JCP Folder, Stewart 650B ATB

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4026 Post(s)
Liked 3,444 Times in 2,092 Posts
Originally Posted by smd4
Which is why the shop tool is made of metal, and not plastic.
As well as often having a closed top end suitable for impacting with a hammer. Andy
__________________
AndrewRStewart
Andrew R Stewart is offline  
Old 09-29-23, 10:48 PM
  #20  
Senior Member
 
Kontact's Avatar
 
Join Date: Apr 2011
Posts: 6,031
Mentioned: 41 Post(s)
Tagged: 0 Thread(s)
Quoted: 3696 Post(s)
Liked 1,015 Times in 678 Posts
Copper water pipe is ideal for this. Won't mar anything but transmits hammer blows like steel. $5 from the hardware store.
Kontact is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell or Share My Personal Information -

Copyright © 2023 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.