My Strange Fork Behavior
#1
aka Sir MaddyX
Thread Starter
Join Date: Sep 2000
Location: Edmonton, Alberta, Canada
Posts: 270
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I just took off my for to be greased the other day and since I pit it back on, it's had a tendency to want to keep me riding in a perfectly straight line. Turning is a little bit stiff. Is this because my bearings are toast? I'm going to full off the neck and from again and see if i can find teh problem but I thought I'd ask here.
Thanks
Thanks
#2
Senior Member
Join Date: Feb 2001
Location: England
Posts: 12,948
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 7 Times
in
7 Posts
Did use use new ball bearings. The old ones were compressed during use, and if you disturn their alignment, the steering may be a bit rough. You may be able to realign them by removing all the cables , loostening the headset and spinning the forks around a few times. Better still, replace them with good quality (ie grade 25) bearings.
#3
NOT a weight weenie
Join Date: Dec 2000
Posts: 1,762
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
If it was working fine before you pulled the fork I don't think the bearings are compressed. It sounds like you over tightened the headset a little too much. Just loosen the headset connection and get it hand tight if it is a threaded and if threadless then turn the screw on the top cap until you get resistence. Now turn the handlebars to the side where the wheel is pointing acorss the frame and act like you are pulling the bars off the stem. Do this back and forth. Does it wobble? If so continue to tighten until this does not happen. Then rotate the bars is the fork stiff? If so check the way the bearings are seated in the races. With threadless typically the lower set is facing up the top set is facing down. Same goes for threaded. If this is not so then correct it. Did this fix it? If not consult your LBS.
#4
aka Sir MaddyX
Thread Starter
Join Date: Sep 2000
Location: Edmonton, Alberta, Canada
Posts: 270
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Ahh yes.. it was my fork that was on there too tight. Now I just have to dislodge my seat post from my frame of better yet, use it as an excuse to buy we a nice new aluminum frame. Wee shall see.
Thanks again for the help.
Thanks again for the help.
#5
NOT a weight weenie
Join Date: Dec 2000
Posts: 1,762
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Kitty, If you are having problems getting a seat post out, put the frame in a stand upside down remove the bb and squirt some Tri Flow up the seat tube and wait it will come out. You can grease a seat post to prevent it from seizing up in a steel frame.
#6
Mr. Cellophane
Join Date: Nov 2000
Location: New Orleans, LA
Posts: 3,037
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Sorry, Dude, the only thing I know about fork problems is that mine makes too many trips to my mouth. :-)
#7
0^0
Join Date: Feb 2001
Location: Rolla, MO
Posts: 4,056
Bikes: Redline Monocog,Surly Crosscheck, Lemond Reno
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
I'm not sure, but you may have tightened the headset to much, I've done that before and had the problem you are describing.
#8
Senior Member
Join Date: Sep 2000
Location: Spokane WA
Posts: 1,148
Bikes: Seven Axiom Ti, Trek 620, Masi cylocross (steel). Masi Souleville 8spd, Fat Chance Mtn. (steel), Schwinn Triple Bar cruiser, Mazi Speciale Fix/single, Schwinn Typhoon
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
If the triflow trick doesn't work try penetrating oil.
You could also try heating the seat tube by pouring boiling water on it or using a hair-dry gun on it to expand the tube.
After you get it it out grease both the tube and the post liberally, so you don't have to fight with it next time
You could also try heating the seat tube by pouring boiling water on it or using a hair-dry gun on it to expand the tube.
After you get it it out grease both the tube and the post liberally, so you don't have to fight with it next time