Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Tap/thread Size for clipless pedals

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Tap/thread Size for clipless pedals

Old 05-29-03, 06:16 AM
  #1  
Newbie
Thread Starter
 
Join Date: May 2003
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Tap/thread Size for clipless pedals

My son finally convinced me to buy clipless pedals for the Bicycle Ride Across Georgia this year. I have an old Schwinn Continental. Unfortunately when we took off one of the old pedals, we saw that the shaft size on the Schwinn is smaller. Does anyone know what tap size/thread to use. The shaft is evidently 9/16th.

Thanks
Kran Riddle is offline  
Old 05-29-03, 06:59 AM
  #2  
Mr. Cellophane
 
RainmanP's Avatar
 
Join Date: Nov 2000
Location: New Orleans, LA
Posts: 3,037
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
According to Sutherland's your old Schwinn cranks probably are probably tapped old USA standard 1/2"x20 TPI. The current standard is 9/16"x20 TPI. You can probably double check this by heading over to Home Depot and try threading a 9/16x20 nut on the pedal threads. Sutherlands offers this tip: When retapping pedal threads, start from the back of the crank arm. Hope this helps.
Regards,
Raymond
__________________
If it ain't broke, mess with it anyway!
RainmanP is offline  
Old 05-29-03, 07:12 AM
  #3  
Newbie
Thread Starter
 
Join Date: May 2003
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Thanks for the info & taking the time to provide.

Kran R.
Kran Riddle is offline  
Old 05-29-03, 07:40 AM
  #4  
Mr. Cellophane
 
RainmanP's Avatar
 
Join Date: Nov 2000
Location: New Orleans, LA
Posts: 3,037
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Glad to help. Welcome to BikeForums! Hang around and ask questions when getting ready for your ride. There is a wealth of experience and friendly advice available here for the asking.
__________________
If it ain't broke, mess with it anyway!
RainmanP is offline  
Old 05-29-03, 09:44 AM
  #5  
Senior Member
 
Join Date: Apr 2003
Location: St Louis, Missouri
Posts: 91
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
I don't think that tapping out your old, forged, one piece crank is a very good idea.

Drilling out the cranks straight and starting the new threads straight is a project that I wouldn't want to attempt using hand held tools. The reason that you tap from the back side of the crank when refreshing pedal threads is to address that very issue. You also have the issue of removing material from where the pedal attaches to the crank arm.
Spoke Wrench is offline  
Old 05-29-03, 10:37 AM
  #6  
Newbie
Thread Starter
 
Join Date: May 2003
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Thanks for the iinput. What do you think then? Am I just stuck without being able to upgrade. My son's next focus is a new bike for me that he plans to grow into.

Kran
Kran Riddle is offline  
Old 05-29-03, 10:55 AM
  #7  
Kev
Senior Member
 
Join Date: Nov 2001
Posts: 1,652
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
What about going down to a machine shop and asking them to rethread the crankarms, I figure it could not cost very much and would be professionaly done then.
Kev is offline  
Old 05-29-03, 12:57 PM
  #8  
Senior Member
 
Avalanche325's Avatar
 
Join Date: Apr 2003
Location: Pasadena, CA
Posts: 3,162

Bikes: Litespeed Firenze / GT Avalanche

Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time in 1 Post
Don't forget left handed thread on the left side. That means buying two taps. It may be just as cheap to have a machine shop do it.
Avalanche325 is offline  
Old 05-29-03, 08:51 PM
  #9  
The Red Lantern
 
Rev.Chuck's Avatar
 
Join Date: Apr 2003
Location: Raleigh NC
Posts: 5,965
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Rather than going to the effort of trying to make the pedals work, use toe clips and straps(Not something I reccomend often) and save towards a new bike that will probably come with clipless pedals any way and be a joy to ride aswell.
__________________
Are you a registered member? Why not? click here to register. Its free, and only takes 27 seconds!
Help out the forums, abide by our community guidelines.

I am in the woods and I have gone crazy.
Rev.Chuck is offline  
Old 05-30-03, 06:07 AM
  #10  
Newbie
Thread Starter
 
Join Date: May 2003
Posts: 4
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
The newbie thanks everyone for taking the time to provide information, advice and input. I have plenty to ponder.

Kran
Kran Riddle is offline  
Old 05-30-03, 08:07 AM
  #11  
Senior Member
 
Join Date: Feb 2002
Location: St. Paul, MN, USA
Posts: 98
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
Up-sizing from the 1/2" to the 9/16" standard not such a great idea. Look at the crankarm, there is not much material there to work with. You may want to simply change out the arms, going with a three-piece bottom bracket. These use cups to down-size the shell to the 1.37" threading for the bottom bracket unit. Look for BMX conversion kits to do this, any good shop should be able to get you more information.

See also One-piece service

(On a technical note, tapping the 9/16" thread requires reaming or drilling of the hole. Use a 33/64-inch drill. The current size of the 1/2" threaded hole will be 29/64. Never use the tap to ream the hole.)
Calvin Jones is offline  

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.