Which way to turn the BB cutters? - For chasing (tapping) threads
#1
Senior Member
Thread Starter
Join Date: Aug 2005
Location: Austin
Posts: 2,104
Bikes: Too many to count
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 4 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Which way to turn the BB cutters? - For chasing (tapping) threads
Hi. I just got a new BB chasing tool, but no instructions. Which way do I turn the cutters for chasing the threads? thanks.
#2
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
Whichever way would tighten a bb on for that side. If it's marked R.H or L.H, this indicates thread direction... not which side of the bike you put it on.
#3
Senior Member
Join Date: Dec 2004
Location: Athens, Ohio
Posts: 5,104
Bikes: Custom Custom Custom
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
The same way you thread in the respective bb cups. Remember use plenty of cutting fluid and go 1/2 turn in, 1/4 turn out.
You also want to have both cutters in the BB. The other cutter acts as a guide and lets you cut the threads correctly aligned
You also want to have both cutters in the BB. The other cutter acts as a guide and lets you cut the threads correctly aligned
#4
META
Join Date: Aug 2005
Location: Madison, WI
Posts: 945
Bikes: Gary Fisher Aquila (retired), Specialized Allez Sport (in parts), Cannondale R500, HP Velotechnic Street Machine, Dented Blue Fixed Gear (retired), Seven Tsunami SSFG, Specialized Stumpjumper Comp Hardtail (alloy version)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
1 Post
Errm... isn't it the case that you shouldn't use cutting fluid on aluminum?
#7
Senior Member
Join Date: May 2003
Location: Mountain Brook. AL
Posts: 4,002
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
Quoted: 303 Post(s)
Likes: 0
Liked 136 Times
in
104 Posts
This one situation where WD40 is useful. It is an adequate to good cutting
fluid for aluminum and if you want to avoid chatter, use some sort of lube
such as WD40. Use any kind of oil in a pinch, bacon grease is another option.
WD40 is not useful for steel or Ti.
fluid for aluminum and if you want to avoid chatter, use some sort of lube
such as WD40. Use any kind of oil in a pinch, bacon grease is another option.
WD40 is not useful for steel or Ti.
#8
META
Join Date: Aug 2005
Location: Madison, WI
Posts: 945
Bikes: Gary Fisher Aquila (retired), Specialized Allez Sport (in parts), Cannondale R500, HP Velotechnic Street Machine, Dented Blue Fixed Gear (retired), Seven Tsunami SSFG, Specialized Stumpjumper Comp Hardtail (alloy version)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
1 Post
operator and nitropowered: what did you guys use? or what are you doing differently?
#9
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
I use the park cutting fluid, it works fine for me. That *is* what it is designed for, cutting/tapping/facing operations etc.
#11
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Kerosene is a good cutting/tapping fluid for Al and that's basically what the majority of WD-40 is.
#12
deep stuff
Join Date: Jun 2007
Location: Nampa, ID
Posts: 250
Bikes: Road, Touring, Mountain Bike
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
When I was working with aluminum a lot as a fabricator, we used a Beeswax when cutting or band-sawing. I think it was actually sold specifically for that purpose.
#13
Senior Member
Join Date: Sep 2005
Posts: 1,959
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Slightly ot- I had the lbs chase the threads on my new frame that was all powdercoated in the bb (steel) and it came back still with powdercoating in the treads. It's must better and the threads feel crisp, but it's still somewhat green (the color) for the most part. Also the sides of the bb, it's been faced like 80-90% around, but there's still a patch of green. I'm assuming (hoping) that there was a slight depression in the side of the bb so rather than keep cutting down to where there wouldn't be any paint left, they just squared it up by taking a minimal amount off.
Anyway, is this typical? I always thought the point of chasing the threads was to remove all the paint. Or is it just mostly to get the threads and bb straightened up to proper depth, etc.?
Anyway, is this typical? I always thought the point of chasing the threads was to remove all the paint. Or is it just mostly to get the threads and bb straightened up to proper depth, etc.?
__________________
fun facts: Psychopaths have trouble understanding abstract concepts.
"Incompetent individuals, compared with their more competent peers, will dramatically overestimate their ability and performance relative to objective criteria."
fun facts: Psychopaths have trouble understanding abstract concepts.
"Incompetent individuals, compared with their more competent peers, will dramatically overestimate their ability and performance relative to objective criteria."
#14
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
Chasing is done to get the threads clean, smooth and at the proper depth. Facing is done to be sure the opposite bottom bracket (or head tube) faces are flat and parallel. If all that's required is scraping off excess paint, that's fine but often some metal has to be removed too.
#15
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
Slightly ot- I had the lbs chase the threads on my new frame that was all powdercoated in the bb (steel) and it came back still with powdercoating in the treads. It's must better and the threads feel crisp, but it's still somewhat green (the color) for the most part. Also the sides of the bb, it's been faced like 80-90% around, but there's still a patch of green. I'm assuming (hoping) that there was a slight depression in the side of the bb so rather than keep cutting down to where there wouldn't be any paint left, they just squared it up by taking a minimal amount off.
Anyway, is this typical? I always thought the point of chasing the threads was to remove all the paint. Or is it just mostly to get the threads and bb straightened up to proper depth, etc.?
Anyway, is this typical? I always thought the point of chasing the threads was to remove all the paint. Or is it just mostly to get the threads and bb straightened up to proper depth, etc.?