Chain slip woes
#1
Senior Member
Thread Starter
Join Date: Jul 2007
Location: Absolute middle of nowhere
Posts: 136
Bikes: 2003 Kona Hahanna
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Chain slip woes
So.
My chain is being pretty annoying.
I replaced the chain and cassette over the winter. I noticed the chain slipping, particularly on rough surfaces and when I'm really on it. Figured chainrings.
Then last night my dad commented that the chain was doing a lot of flopping and looked wicked loose when I rode. Hmm. Pop it off and lay it down next to the old one, a few inches too long. Hmm. Take off two links so it's as close as it's gonna be to the same length and put it back on. Now it is absolutly awful. It slips under any stress. If I gently pedal in a low gear it'll only do so every couple of turns. It's making a pretty steady tick somehwere down there.
So, chainrings? They're original on a 2003 so I figure they're due. Also, the chain is a just a bit longer. It would be exact if I took off a wide link thing but then I couldn't close the chain.
Thoughts?
SRAM cassette and chain, Suntour cranks (dunno who made the chainrings). Would different companies make a difference?
My chain is being pretty annoying.
I replaced the chain and cassette over the winter. I noticed the chain slipping, particularly on rough surfaces and when I'm really on it. Figured chainrings.
Then last night my dad commented that the chain was doing a lot of flopping and looked wicked loose when I rode. Hmm. Pop it off and lay it down next to the old one, a few inches too long. Hmm. Take off two links so it's as close as it's gonna be to the same length and put it back on. Now it is absolutly awful. It slips under any stress. If I gently pedal in a low gear it'll only do so every couple of turns. It's making a pretty steady tick somehwere down there.
So, chainrings? They're original on a 2003 so I figure they're due. Also, the chain is a just a bit longer. It would be exact if I took off a wide link thing but then I couldn't close the chain.
Thoughts?
SRAM cassette and chain, Suntour cranks (dunno who made the chainrings). Would different companies make a difference?
#2
Keep on climbing
Is this the first chain replacement you've done on this bike? If so, it's probable that the original chain wore down the chain-rings to the point that the chain-rings just won't mesh with a new chain anymore. I'm assuming the slipping is occurring on the chain-rings and not the cogs?
#3
Amateur Hack
Join Date: Oct 2005
Location: Austin
Posts: 135
Bikes: Marin mtb turned tri turned commuter turned singlespeed, Haro Werks 2.0, Specialized Epic Allez carbon main tube built up for triathlons
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
tell us more about this tick. is it there when not pedaling? is it there at a certain point in the pedal stroke?
you may have a stiff link in there somewhere. maybe you squeezed the pin too tight when you put the chain back together. just tossing that out there as a lower cost issue than replacing the chain rings.
you may have a stiff link in there somewhere. maybe you squeezed the pin too tight when you put the chain back together. just tossing that out there as a lower cost issue than replacing the chain rings.
#4
Senior Member
Join Date: Apr 2007
Posts: 351
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I had a slipping chain. Replaced the freewheel. Still bad. Replaced the chain. Still bad.
Cursed hawed and cried, still bad.
Replaced rear Derailleur, problem solved. Shouldn't have made any difference, but it did.
Cursed hawed and cried, still bad.
Replaced rear Derailleur, problem solved. Shouldn't have made any difference, but it did.
#6
Senior Member
Thread Starter
Join Date: Jul 2007
Location: Absolute middle of nowhere
Posts: 136
Bikes: 2003 Kona Hahanna
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Is this the first chain replacement you've done on this bike? If so, it's probable that the original chain wore down the chain-rings to the point that the chain-rings just won't mesh with a new chain anymore. I'm assuming the slipping is occurring on the chain-rings and not the cogs?
tell us more about this tick. is it there when not pedaling? is it there at a certain point in the pedal stroke?
you may have a stiff link in there somewhere. maybe you squeezed the pin too tight when you put the chain back together. just tossing that out there as a lower cost issue than replacing the chain rings.
you may have a stiff link in there somewhere. maybe you squeezed the pin too tight when you put the chain back together. just tossing that out there as a lower cost issue than replacing the chain rings.
Thanks for the input
#7
Senior Member
Join Date: Apr 2007
Posts: 351
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#9
Keep on climbing
#10
Senior Member
Join Date: Jul 2006
Location: Brainerd MN
Posts: 999
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
#11
Senior Member
Thread Starter
Join Date: Jul 2007
Location: Absolute middle of nowhere
Posts: 136
Bikes: 2003 Kona Hahanna
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I use this stuff
Anyway, That made some pretty significant progress (At the beginning I could barely make it move, now its pretty close to what it should be). After like 45 mins I got bored, though haha.
Anyway, That made some pretty significant progress (At the beginning I could barely make it move, now its pretty close to what it should be). After like 45 mins I got bored, though haha.