Tire (Tyre) pressure
#1
Newbie
Thread Starter
Join Date: Oct 2001
Location: Lexington, KY
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Tire (Tyre) pressure
I'm new to biking and have a question regarding tire pressure. I started into biking by purchasing a used road bike. I inflate the tires to the recommended pressure of 110psi, but when I check the pressure two or three days later it has dropped back to the 90-95psi range. Is this normal? Could the age or wear of the tubes or tires cause a slow leak? The tires appear OK except for a few small cracks along the sidewall, I suspect from the previous owner running underinflated.
If I have to top off tire pressure every few days I definitely need to invest in a better pump!
If I have to top off tire pressure every few days I definitely need to invest in a better pump!
#2
Banned
Join Date: Aug 2001
Location: upstate New York
Posts: 1,688
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
First, let me ask, is 110 psig the recommended tyre pressure, or the maximum tyre pressure? If it is the latter, why do you keep it so high?
As far as the leaking air, it is coming out in one of 3 ways:
1) through a leaky valve
2) through a small puncture
3) through the rubber itself
The first 2 are easy to fix, by either replacing the tube, or patching the puncture. Air leaking through the rubber, thoug, is natural, but different tubes leak down at different rates.
Latex tubes are notorious leakers, often losing 25-30% of their air overnight. The only reason they still exist at all is because they are quite light. Butyl rubber, on the other hand, is usually quite impermeable-until it gets old.
Chances are that the tube is toast, so you would do well to replace it.
As far as the leaking air, it is coming out in one of 3 ways:
1) through a leaky valve
2) through a small puncture
3) through the rubber itself
The first 2 are easy to fix, by either replacing the tube, or patching the puncture. Air leaking through the rubber, thoug, is natural, but different tubes leak down at different rates.
Latex tubes are notorious leakers, often losing 25-30% of their air overnight. The only reason they still exist at all is because they are quite light. Butyl rubber, on the other hand, is usually quite impermeable-until it gets old.
Chances are that the tube is toast, so you would do well to replace it.
__________________
Je vais à vélo, donc je suis!
Je vais à vélo, donc je suis!
#3
Senior Member
Join Date: Dec 2001
Location: Southwest VA
Posts: 56
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Losing air is inevitable when you have to run high pressure in butyl tubes. Road tires are especially susceptable as they have relatively little volume and much higher pressure than MTB stuff. The reality is...you need to air them up when you are going riding. I would however check the tires out for dry-rot to make sure they ar still in fair shape. Cracking is usually from lack of use instead of too low a pressure. Good Luck
#4
Senior Member
Join Date: Dec 2001
Location: Downey, CA.
Posts: 1,166
Bikes: Litespeed Classic (55cm), Specialized Tarmac Pro (56cm)
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 7 Post(s)
Likes: 0
Liked 6 Times
in
4 Posts
Callbr549,
Let me start by saying that as stated by Geronimo tires will lose pressure over time. 110 psi is not unheard of for road bike tires and you want to try to maintain tire pressure at that level so that you reduce rolling resistance. The downside to high pressure tires is that you get a hard ride. You probably should get yourself a good floor pump with a built-in pressure gauge that accepts both presta and schrader valves if you don’t already have one. Hope this helps.
Let me start by saying that as stated by Geronimo tires will lose pressure over time. 110 psi is not unheard of for road bike tires and you want to try to maintain tire pressure at that level so that you reduce rolling resistance. The downside to high pressure tires is that you get a hard ride. You probably should get yourself a good floor pump with a built-in pressure gauge that accepts both presta and schrader valves if you don’t already have one. Hope this helps.
__________________
Litespeed, lasts a lifetime.
Specialized Tarmac, lasts a lifetime, or until it breaks.
Litespeed, lasts a lifetime.
Specialized Tarmac, lasts a lifetime, or until it breaks.
#5
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,336 Times
in
842 Posts
Sheldon has a good article which relates recommended tyre pressure to tyre width and the rider's weight. I finally bought a new Nashbar floor pump with a dual head and a built-in pressure gauge, which makes it very easy to maintain ~100psi.
#7
HomeBrew Master!
Join Date: Jan 2001
Location: West Central Illinois
Posts: 2,208
Bikes: Aegis Aro Svelte, Surly LHT, Cannondal R3000 tandem, Santana Triplet.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Your pressure loss is normal.
I run my tires at max pressure always. Like Bobsled mentions, it reduces rolling resistance. It also goes a long way in preventing "pinch flats" or "snake bites". These are flats associated with hitting small rocks or other debris causing the tube to be smashed up (or sideways) into the rim. Thus catching the tube between the two and puncturing it.
If you had a problem with a slow leak, your tire would be flat or almost totally flat in less than a couple of days. Use a good floor pump and top off both tires before you ride.
I run my tires at max pressure always. Like Bobsled mentions, it reduces rolling resistance. It also goes a long way in preventing "pinch flats" or "snake bites". These are flats associated with hitting small rocks or other debris causing the tube to be smashed up (or sideways) into the rim. Thus catching the tube between the two and puncturing it.
If you had a problem with a slow leak, your tire would be flat or almost totally flat in less than a couple of days. Use a good floor pump and top off both tires before you ride.
#8
The Female Enduro
Join Date: Apr 2000
Location: Pennsylvania, United States of America
Posts: 1,183
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Yup, I'm always at max. pressure, too.
But, you always will loose some air, that's normal. Just as long as when you come back to the bike they're not flat, you're good to put a little air in and ride off without a worry.
velo
But, you always will loose some air, that's normal. Just as long as when you come back to the bike they're not flat, you're good to put a little air in and ride off without a worry.
velo
#9
Banned
Join Date: Aug 2001
Location: upstate New York
Posts: 1,688
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Lance Armstrong rides with his tyres (competition road tyres, probably all good for 140 psig, minimum) at 125 psig rear, 105 psig front.
__________________
Je vais à vélo, donc je suis!
Je vais à vélo, donc je suis!
#10
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,336 Times
in
842 Posts
Anyone who tends to wear out sidewalls before treads could probably benefit from more pressure. I like Lance's concept of carrying somewhat more pressure on the rear tyre, particularly if using a rear rack or panniers.
#11
Banned.
Join Date: Aug 2001
Posts: 20,917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 12 Times
in
10 Posts
First, let me ask, is 110 psig the recommended tyre pressure, or the maximum tyre pressure? If it is the latter, why do you keep it so high?
In 12,000 miles of riding (6,500 on mtn bike and 5,500 on road) I have never had any problems from either wheels or tires, except for the perfunctory flat from thorns and glass.
So, why do you not seem to recommend 120+ psi pressures for the road bike??
#12
Banned
Join Date: Aug 2001
Location: upstate New York
Posts: 1,688
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Well, this thread seems to be going astray!
On my road bike, which uses 21mm wide tubulars, I usually ride with 135 rear, 110 front. I will occasionally pump them up to 145/120 for speed, or run them at 125/100 for comfort on long rides. Both tyres are rated for a maximum of 175 psig.
On my touring bike, which uses 32mm wide clinchers (Armadillos), I generally ride with 90 rear/75 front, even though they are rated for 110 psig maximum. If I'm carrying a lot of weight in the panniers, I may increase the pressure to 100/85, but any higher makes the ride quite harsh.
There are some competition tubulars available which have a maximum pressure of 220psig, but I don't know anybody who actually rides with them at that pressure.
On my road bike, which uses 21mm wide tubulars, I usually ride with 135 rear, 110 front. I will occasionally pump them up to 145/120 for speed, or run them at 125/100 for comfort on long rides. Both tyres are rated for a maximum of 175 psig.
On my touring bike, which uses 32mm wide clinchers (Armadillos), I generally ride with 90 rear/75 front, even though they are rated for 110 psig maximum. If I'm carrying a lot of weight in the panniers, I may increase the pressure to 100/85, but any higher makes the ride quite harsh.
There are some competition tubulars available which have a maximum pressure of 220psig, but I don't know anybody who actually rides with them at that pressure.
__________________
Je vais à vélo, donc je suis!
Je vais à vélo, donc je suis!
#13
human
Join Date: Jun 2001
Location: living in the moment
Posts: 3,562
Bikes: 2005 Litespeed Teramo, 2000 Marinoni Leggero, 2001 Kona Major Jake (with Campy Centaur), 1997 Specialized S-Works M2, 1992 Specialized Rockhopper
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 1 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
It actually depends on the shape/size of the tire and the composition of the rubber. I run my 23mm Conti GP3000s at the max -- 120 psi. I find the rubber a bit grippy and I find that I can have the best of both worlds -- grip and speed -- at high pressure. My Vrewdestein Fortezza Tri-Comps have a max rated pressure of 160 [or is it 145? I'll check]. But I find that they don't grip AT ALL at pressures above 120 psi. I normally run them 115 back and 105-110 front. I did jonce have them both at 135 on a group ride once, but it started to rain and the bike started getting mighty skittish.
[BTW... I like Vreds. I just can't afford to buy them often... and the sidewalls tend to shed threads like nobody's business.]
[BTW... I like Vreds. I just can't afford to buy them often... and the sidewalls tend to shed threads like nobody's business.]
__________________
when walking, just walk. when sitting, just sit. when riding, just ride. above all, don't wobble.
The Irregular Cycling Club of Montreal
Cycling irregularly since 2002
when walking, just walk. when sitting, just sit. when riding, just ride. above all, don't wobble.
The Irregular Cycling Club of Montreal
Cycling irregularly since 2002
#14
Banned.
Join Date: Aug 2001
Posts: 20,917
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 12 Times
in
10 Posts
Originally posted by D*Alex
Well, this thread seems to be going astray!
Well, this thread seems to be going astray!
Oops!! Well, what do you know. It IS about tire pressure.
#15
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,336 Times
in
842 Posts
One of my friends from the U.K. recommends reducing tyre pressure about 10 percent when cycling (or driving) in wet weather, to improve traction.
#16
Donating member
Join Date: Sep 2001
Location: Faversham, Kent, UK
Posts: 1,852
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
One of my friends from the U.K. recommends reducing tyre pressure about 10 percent when cycling (or driving) in wet weather, to improve traction.
In which case on the road does tread have any practical use?
Richard
__________________
Currently riding an MTB with a split personality - commuting, touring, riding for the sake of riding, on or off road :)
Currently riding an MTB with a split personality - commuting, touring, riding for the sake of riding, on or off road :)
#17
feros ferio
Join Date: Jul 2000
Location: www.ci.encinitas.ca.us
Posts: 21,807
Bikes: 1959 Capo Modell Campagnolo; 1960 Capo Sieger (2); 1962 Carlton Franco Suisse; 1970 Peugeot UO-8; 1982 Bianchi Campione d'Italia; 1988 Schwinn Project KOM-10;
Mentioned: 44 Post(s)
Tagged: 0 Thread(s)
Quoted: 1394 Post(s)
Liked 1,336 Times
in
842 Posts
Sheldon claims that bicycle road tyre tread is worthless, and my experience supports this. Although your logic about aquaplaning and pressure makes perfect sense, I feel much more secure on 28mm or wider tyres when the road is wet, and consider my Bianchi, with its 23mm Contis, to be a fair-weather friend.
#18
Donating member
Join Date: Sep 2001
Location: Faversham, Kent, UK
Posts: 1,852
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I seem to recall D*Alex pointing out that narrower tyres should give better traction because of the greater psi (I hope I'm paraphrasing him reasonably accurately ) and again I see the logic but I like the idea of the extra contact area.
Richard
Richard
__________________
Currently riding an MTB with a split personality - commuting, touring, riding for the sake of riding, on or off road :)
Currently riding an MTB with a split personality - commuting, touring, riding for the sake of riding, on or off road :)
#19
Newbie
Thread Starter
Join Date: Oct 2001
Location: Lexington, KY
Posts: 3
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
I want to thank everyone for their replies to my original post. While I seem to have touched off a lively debate about tire pressure, tread, etc, I also got my basic question answered. There seems to be a consensus that my experience of losing 10-15 psi every few days is probably normal. Thanks for sharing your experience.