Properly Applying Phil's Tenacious Oil to Chain
#1
Senior Member
Thread Starter
Join Date: Jul 2008
Location: The Big D
Posts: 457
Bikes: All City Nature Boy, All City Macho Man
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Properly Applying Phil's Tenacious Oil to Chain
Even if I use just the tiniest amount directly applied to each chain roller, it still strings between my chainring and chain and cog in the back. It gets all over my chainstay, my leg, my wheel, my spokes - basically everywhere. I wanted to use it, but I have just been using some Finish Line wet lube, which works well enough.
Is this everyone's experience using this stuff on a chain? Or is there a better way to do it so that my legs aren't lubricated? Or does it eventually stop slinging oil everywhere after a few hundred miles of riding?
Is this everyone's experience using this stuff on a chain? Or is there a better way to do it so that my legs aren't lubricated? Or does it eventually stop slinging oil everywhere after a few hundred miles of riding?
#2
Senior Member
Join Date: Jul 2005
Posts: 3,268
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 118 Post(s)
Likes: 0
Liked 50 Times
in
25 Posts
I'm not familiar with the viscosity of tenacious oil, but I doubt it is too thick. This works to get a minimal but sufficient amount of Pro Link into my chain rollers. On a nappy washcloth (thick nap holds oil well) soak a spot about 1" in diameter. Hold it up against the rollers and rotate the chain slowly. Do top and bottom. Capillary action will take it into the rollers. Wipe the sides of the chain clean with a dry part of the cloth. There shouldn't be any excess.
Run your finger back and forth along the length of the chain on the rollers. You should be able to feel well lubed rollers turning smoothly. After a few rides, run your fingers along it again. You'll know when it's time to clean/lube again. bk
Run your finger back and forth along the length of the chain on the rollers. You should be able to feel well lubed rollers turning smoothly. After a few rides, run your fingers along it again. You'll know when it's time to clean/lube again. bk
#3
Senior Member
Join Date: Jun 2007
Location: A Coffin Called Earth. or Toronto, ON
Posts: 12,258
Bikes: Bianchi, Miyata, Dahon, Rossin
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 3 Post(s)
Likes: 0
Liked 5 Times
in
5 Posts
the thickness is quite similar to 10W30 motor oil.
just add some mineral spirits to thin it out a bit.
just add some mineral spirits to thin it out a bit.
__________________
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
Food for thought: if you aren't dead by 2050, you and your entire family will be within a few years from starvation. Now that is a cruel gift to leave for your offspring. ;)
https://sanfrancisco.ibtimes.com/arti...ger-photos.htm
#4
Great State of Varmint
Join Date: Sep 2008
Location: Dante's Third Ring
Posts: 7,476
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 15 Times
in
15 Posts
One drop per link. Then run the chain through a towel to remove any excess. And it sounds like this stuff has plenty of that. I'll stick with Boeshield T-9, TYVM.