Just got a new stem - steerer question
#1
Senior Member
Thread Starter
Join Date: Feb 2008
Location: UK
Posts: 2,324
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Just got a new stem - steerer question
Hi all,
I have just got a new stem and it fits on the steerer ok, however there is a bit of steerer left above it. I don't want to cut it so is it ok to just put a spacer on it and then replace the cap?
Thanks
Daven
I have just got a new stem and it fits on the steerer ok, however there is a bit of steerer left above it. I don't want to cut it so is it ok to just put a spacer on it and then replace the cap?
Thanks
Daven
#4
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,363
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
A spacer above the stem doesn't hurt anything. Just make sure the spacer is about 3mm above the steer tube...just like a stem would be.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#5
Senior Member
Thread Starter
Join Date: Feb 2008
Location: UK
Posts: 2,324
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Oh so a stem is MEANT to be above the steerer slightly? I thought that it shouldn't as then one screw would only have 1/2 a grip on the steerer. Thanks for the help, I just went for a test ride and all seemed well
#6
Mad bike riding scientist
Join Date: Nov 2004
Location: Denver, CO
Posts: 27,363
Bikes: Some silver ones, a red one, a black and orange one, and a few titanium ones
Mentioned: 152 Post(s)
Tagged: 1 Thread(s)
Quoted: 6219 Post(s)
Liked 4,218 Times
in
2,365 Posts
The stem should be slightly above the steer tube. 3mm is about 1/8". If the steer tube is flush with the top of the stem, the top cap can't compress the bearings in the headset properly. You'll end up with a loose headset...not a good thing.
__________________
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
Stuart Black
Plan Epsilon Around Lake Michigan in the era of Covid
Old School…When It Wasn’t Ancient bikepacking
Gold Fever Three days of dirt in Colorado
Pokin' around the Poconos A cold ride around Lake Erie
Dinosaurs in Colorado A mountain bike guide to the Purgatory Canyon dinosaur trackway
Solo Without Pie. The search for pie in the Midwest.
Picking the Scablands. Washington and Oregon, 2005. Pie and spiders on the Columbia River!
#7
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
In fact, for carbon steerers, having the steerer project above the stem is desirable to assure the steerer fully supports the stem. Then a spacer above the stem is used to achieve the needed headset adjustment gap.
#8
Senior Member
Thread Starter
Join Date: Feb 2008
Location: UK
Posts: 2,324
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 3 Times
in
3 Posts
Cool it is around 3mm above I think. Can't be bothered to start changing around spacers right now so I will see how it goes - if I need more height to the bars I will have to change them around!
#9
hello
But more importantly, are you happy with the height of the stem? Spacers can be placed anywhere, above or below, or combination of both.
#10
cab horn
Join Date: Jun 2004
Location: Toronto
Posts: 28,353
Bikes: 1987 Bianchi Campione
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 26 Times
in
19 Posts
Especially if it's a carbon steerer NO part of the stem should be above the steerer. The red line is draw where the uppermost pinch bolt rests - not above the steerer. On a pro assembled floor bike there is nearly always a 5mm spacer on top of the stem before the cap.