Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

8 speed freewheel

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

8 speed freewheel

Old 08-04-10, 07:38 AM
  #1  
Banned
Thread Starter
 
Join Date: Jul 2010
Posts: 154
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
8 speed freewheel

I'm aware that the issue with 8 speed freewheels is they can cause axles to bend, however, if I'm building a bike for my girlfriend who only weighs 135lbs, is this still going to be a major issue?
use.
My gf is new to cycling having only rented a bike once and ridden her moms comfort bike. She liked how upright she was on her moms comfort bike so I'm thinking flatbar is the way to go for her.
Kindly refrain from telling me not to go the freewheel route for the time being. I recently did a rebuild of an old nishiki to get my feet wet with wrenching again. I'll be taking the drop bars and stem from that bike and putting it on my current flatbar bike and taking the 8 speed shifters from my flat bar and putting it onto whatever frame I acquire for her. I am aware I can use my 8 speed shifters with my existing 7speed freewheel but i figure if i can get her an extra gear safely I might as well since freewheels are so much cheaper than casettes.
bigdaddy10028 is offline  
Old 08-04-10, 08:16 AM
  #2  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,544

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,425 Times in 1,341 Posts
Since you already have the wheel, go ahead and use it. Yes there is an increased axle bending risk, but it's not like it'll happen tomorrow. As you say she only weighs 135#s.

Note that the greatest bending force isn't from weight but from chain tension. When hill climbing in low gear the chain tension usually is much higher than the axle weight, and is inboard of the axle ends creating bending load. One thing that helps improve axle strength is a broad locknut on the right side, which provides some cantilever strength off the right dropout.

BTW- be aware that you'll have to respace the axle for the wider freewheel, and re-dish the wheel accordingly.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is offline  
Old 08-04-10, 08:52 AM
  #3  
Senior Member
 
Join Date: Oct 2008
Location: Right where I'm supposed to be
Posts: 1,628

Bikes: Franklin Frames Custom, Rivendell Bombadil

Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
Quoted: 114 Post(s)
Liked 205 Times in 124 Posts
Originally Posted by bigdaddy10028
I'm aware that the issue with 8 speed freewheels is they can cause axles to bend, however, if I'm building a bike for my girlfriend who only weighs 135lbs, is this still going to be a major issue?
.

Probably not, though it depends on the quality of the axle on the hub used also. A Phil Wood has no issues of axles breaking because they're oversized.

The value of more speeds though , is highly debatable.
Garthr is offline  
Old 08-04-10, 09:34 AM
  #4  
Banned
Thread Starter
 
Join Date: Jul 2010
Posts: 154
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
as for the respacing issue, this is a new wheel, not a vintage replacement wheel. That means I shouldn't have to redish or respace the wheel correct? the nishiki was a 10 speed but i just bought a brand new 130mm freewheel and put the 7speed freewheel on and haven't had any issues.

As for the value of more speeds, she and I won't be doing any crazy amounts of riding together but I can think of a couple of routes we would take that might get a bit steep. Current 7speed freewheel is 14-34 with the big jump from 24-34. Personally i find the 28tooth cog quite useful so I'd love to be able to use a 13-32 8speed freewheel for her and give her back that 28 tooth gear.
bigdaddy10028 is offline  
Old 08-04-10, 09:45 AM
  #5  
cab horn
 
Join Date: Jun 2004
Location: Toronto
Posts: 28,353

Bikes: 1987 Bianchi Campione

Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
Quoted: 42 Post(s)
Likes: 0
Liked 25 Times in 18 Posts
Originally Posted by Garthr
Probably not, though it depends on the quality of the axle on the hub used also. A Phil Wood has no issues of axles breaking because they're oversized.

The value of more speeds though , is highly debatable.
Lol.

Obviously the reason he isn't going freehub is because of cost issues. And you tell him to put a phil wood on there. Save your money and buy a modern 8/9/10 freehub. Cheaper and you have the option of putting 9/10 on that same hub in the future.
operator is offline  
Old 08-04-10, 10:03 AM
  #6  
Banned
Thread Starter
 
Join Date: Jul 2010
Posts: 154
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
lol, my gf doesn't necessarily WANT a bike, but she likes us to do things together. I'm in the fitness biz, she comes to bootcamp classes all the time and I train her in the gym a lot but we never do anything athletic TOGETHER. I hate running and then to compound it I blew out my ACL in the winter so i bought a bike and totally fell in love with it and I really think that once she gets comfortable enough with riding in a bit of traffic and has a bike that fits her she would also love it. So far she has ridden two bikes, The first was a giant cypress rental special. It's probably about 35 lbs, has annoying gripshifters , humongous 38mm tires and mtb gearing. She is in great shape but couldn't keep up with me when I wasn't even pedaling. The other bike was her moms specialized crossroads which is similar to the cypress, ridiculously heavy and made for cruising. We live on the 5th floor and her bike is going to have to be carried upstairs. I figure I could easily build her an aluminum frame flatbar down around the 22lb range for relatively short money. I think a huge part of her getting into this is going to be getting on a proper bike. When I bought my giant in february it was eyeopening! I hadn't ridden a bike since my teenage years and I never rode anything fitted to me. One test ride and I was in love with my bike. So yeah, no need for phil wood hubs and crazy amounts of gears.

I already have a wheelset, bars, stem, flat bar brifters. Ijust bought a truvativ elita 30/42/52 crankset from ebay for $35 and I already have the appropriate bottom bracket. So ultimately I just need a frame and fork which I can get each of them from nashbar for $100 each and i figure they always have crazy deals going on so probably get them both for 80 each. and should be able to build this thing nicely for cheap.
bigdaddy10028 is offline  
Old 08-04-10, 11:21 AM
  #7  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,544

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,425 Times in 1,341 Posts
reminder. 8s freewheels are wider than 7s freewheels so, unless there was about 5mm extra between the 1st 7s sprocket and the frame, you will need to respace or replace the axle.

Then you have a choice, you can re-dish the wheel to offset 1/2 the added right side spacing, or you can use a 135mm axle and spread the frame, but probably not have to re-dish the wheel. IMO, the wider axle is the better choice, and if you don't do your own wheel work the axle and QR skewer might come out cheaper.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.

Last edited by FBinNY; 08-04-10 at 11:26 AM.
FBinNY is offline  
Old 08-04-10, 11:31 AM
  #8  
Banned
Thread Starter
 
Join Date: Jul 2010
Posts: 154
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
thanks for the info, very useful. I'll just stick to the 7 and should we decide to get her to 8 speeds I'll make the transition over to freehub.
bigdaddy10028 is offline  
Old 08-04-10, 11:52 AM
  #9  
Banned
 
Join Date: Jun 2010
Location: NW,Oregon Coast
Posts: 43,598

Bikes: 8

Mentioned: 197 Post(s)
Tagged: 0 Thread(s)
Quoted: 7607 Post(s)
Liked 1,354 Times in 861 Posts
8th cog , same space between cogs,N+1, is why frames were made with 130 wide dropouts when 126 was OK before.

Its not how many gears, It's the Ratios.. build wheels around Phil Wood's freewheel hubs and the axles will not Bend.

from what I read , consider getting a Tandem, that will be something you can do together, and share the effort ,
rather than you perhaps dropping her , [and she getting pissed, as a result]

and if you want drop bars for yourself, but she wants an upright position that can be accommodated.
fietsbob is offline  
Old 08-04-10, 12:06 PM
  #10  
Banned
Thread Starter
 
Join Date: Jul 2010
Posts: 154
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times in 0 Posts
the cost of building wheels with phil wood hubs is more expensive than buying entry level freehub wheels. I can get an entry level freehub wheel for 30 bucks but since i already have a freewheel, I'm just going to build her bike with it.

Tandem is never going to happen. Lets not forget the coolness factor when dealing with a woman!

I think what FBNY was getting at was if i was attempting to put an 8speed freewheel on a 126mm frame i could def have issues. In this instance i'd be using a 130mm freewheel hub wheel on a modern 130mm spaced frame. I didn't think the wheel would need to be redished for this but I will defer to you veterans. ultimately it's not that big of a deal, I can still get her a 13-28 7 speed freewheel instead of the 14-34 and it will match the gearing on my 8 speed which is 11-28 (i have the extra top end gear this setup gets me up most hills plenty easy but the 34 tooth bailout is a nice option.)
bigdaddy10028 is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
clengman
Classic & Vintage
22
07-10-18 12:23 PM
vintagerando
Bicycle Mechanics
36
02-06-16 12:34 AM
bikemig
Bicycle Mechanics
2
10-06-15 06:23 AM
noglider
Bicycle Mechanics
8
07-28-10 01:42 PM
ScrawnyKayaker
Singlespeed & Fixed Gear
11
06-20-10 06:20 PM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.