Custom made crank set
#1
Senior Member
Thread Starter
Join Date: Mar 2009
Location: Arkansas
Posts: 671
Bikes: Surly LHT 52cm Nice Bicycle I think.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
Custom made crank set
Has anyone here ever made there own crank set if so why.I made one my self but it cost more than it would have if I had just order a set.But this was the only why I could get this crank set.
#2
Senior Member
The cost of making your own set must have been many times more than the cost of buying one. What is so unusual about your situation that required it and what length of cranks did you get?
There was a thread around here a while back about a guy that makes very short cranks so that folks with knee mobility issues can continue to ride. The fellow that started it also claimed that it was surprisingly effective. Not a lot of torque but easy to spin at a much higher than normal cadence to make up for the lack of torque. The short arms were done by simply drilling the arms and spot facing the drill points and then threading the arms. The excess being then cut off and the end re-profiled.
There was a thread around here a while back about a guy that makes very short cranks so that folks with knee mobility issues can continue to ride. The fellow that started it also claimed that it was surprisingly effective. Not a lot of torque but easy to spin at a much higher than normal cadence to make up for the lack of torque. The short arms were done by simply drilling the arms and spot facing the drill points and then threading the arms. The excess being then cut off and the end re-profiled.
#3
Senior Member
Join Date: Feb 2001
Location: England
Posts: 12,948
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 19 Post(s)
Likes: 0
Liked 7 Times
in
7 Posts
Besides the crank shortening service offered by a few workshops, the main reason to go custom is for large size. Specialities TA do a fair size range and Zinn do extra long ones (which require high bottom brackets for clearance).
TA and Middleburn make separate crank/spider assemblies that you can mix and match.
TA and Middleburn make separate crank/spider assemblies that you can mix and match.
#4
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
I hope you had good metalurgical skills when you made your own cranks. Years ago there were a bunch of boutique crank makers who made custom CNC'ed cranks out of billet Aluminum. Their CNC skills were far better than their knowledge of metalurgy and the failure rate was very high.
#5
Bianchi Goddess
Join Date: Apr 2009
Location: Shady Pines Retirement Fort Wayne, In
Posts: 27,858
Bikes: Too many to list here check my signature.
Mentioned: 192 Post(s)
Tagged: 2 Thread(s)
Quoted: 2930 Post(s)
Liked 2,923 Times
in
1,491 Posts
KDC you mean you actually forged or CNCd a crankset or did you use a stock crank and swapp the rings around?
Michael thanks for the link but unfortunatly I can't afford such sexxy rings. although it does give me a few ideas
Michael thanks for the link but unfortunatly I can't afford such sexxy rings. although it does give me a few ideas
__________________
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
“One morning you wake up, the girl is gone, the bikes are gone, all that's left behind is a pair of old tires and a tube of tubular glue, all squeezed out"
Sugar "Kane" Kowalczyk
#6
Senior Member
Thread Starter
Join Date: Mar 2009
Location: Arkansas
Posts: 671
Bikes: Surly LHT 52cm Nice Bicycle I think.
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 1 Time
in
1 Post
No what I did was to get a crank spider and then get my chain rings with no pins or ramp on them and built it up this way I am using the old school friction shifters.
The chain rings are 46t,36t,26t I have about 150.00 in my set.Last year I bought a crank set with 44t,32t,22t for 39.00 it works great on my Surly LHT but this crank
set I made it for my new build I will be working on this winter.This gives me something to do.
The chain rings are 46t,36t,26t I have about 150.00 in my set.Last year I bought a crank set with 44t,32t,22t for 39.00 it works great on my Surly LHT but this crank
set I made it for my new build I will be working on this winter.This gives me something to do.
#8
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,096 Times
in
742 Posts
#9
Banned
So this is about assembling a non standard set of chainrings on an existing crank arm set..?
if that is the case, then it is safe to assume many combinations are possible,
as long as the bolt circles match up and the chainline works when you're done.
Non Indexed, friction/ratchet shifting allows more flexibility.
I put down market steel chainrings on my touring bikes crankarms , and got increased wear-life out of them,
as well as choosing them for their tooth count.
if that is the case, then it is safe to assume many combinations are possible,
as long as the bolt circles match up and the chainline works when you're done.
Non Indexed, friction/ratchet shifting allows more flexibility.
I put down market steel chainrings on my touring bikes crankarms , and got increased wear-life out of them,
as well as choosing them for their tooth count.
#10
Old fart
Join Date: Nov 2004
Location: Appleton WI
Posts: 24,784
Bikes: Several, mostly not name brands.
Mentioned: 153 Post(s)
Tagged: 0 Thread(s)
Quoted: 3587 Post(s)
Liked 3,400 Times
in
1,934 Posts
I hope you had good metalurgical skills when you made your own cranks. Years ago there were a bunch of boutique crank makers who made custom CNC'ed cranks out of billet Aluminum. Their CNC skills were far better than their knowledge of metalurgy and the failure rate was very high.
That said, builders like René Herse would purchase raw crank arm forgings and machine them in house to their own specifications. The boutique CNC machinists used plain billet.
Last edited by JohnDThompson; 10-27-10 at 05:46 PM.