Go Back  Bike Forums > Bike Forums > Bicycle Mechanics
Reload this Page >

Slight hop on wheel

Notices
Bicycle Mechanics Broken bottom bracket? Tacoed wheel? If you're having problems with your bicycle, or just need help fixing a flat, drop in here for the latest on bicycle mechanics & bicycle maintenance.

Slight hop on wheel

Old 03-20-11, 04:46 PM
  #1  
Senior Member
Thread Starter
 
Join Date: Jun 2010
Location: Pearland, Texas
Posts: 7,579

Bikes: Cannondale, Trek, Raleigh, Santana

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 308 Post(s)
Liked 3 Times in 3 Posts
Slight hop on wheel

Hi All, I'm trying to true the wheel, but I can't get rid of a small hop. Honestly it doesn't effect ride, but it's now a quest. It seems easier, or I've been lucky, to repair/true a well out of true wheel than this one so I think it's something subtle I'm missing.

The wheel is a 700C and the hop is about 1/4-1/3" at midpoint and runs along the rim for about 8".

TIA, Brad
bradtx is offline  
Old 03-20-11, 05:14 PM
  #2  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,545

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,432 Times in 1,345 Posts
Getting rid of hop, especially a low spot, is the hardest thing to do when aligning a tight wheel. Unlike wobble, hop requires the rim to move along the circumference because higher radius implies longer circumference. That means that when you bring a hop in the extra material needs to be spread along the entire circumference, against the resistance of the other spokes.

1/4" is quite a lot, and I wonder how it got there in the first place. Pulling it down will require staggering tension, and will also cause tension unbalance as the material tries to flow out. I suggest you carefully lower the overall tension by degrees, working about 1/4 turn at a time, until you're at about half tension. Then you can work on the hop, getting the wheel round, and tension fairly even before reloading back to normal tension by degrees.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is offline  
Old 03-20-11, 05:48 PM
  #3  
Senior Member
 
Join Date: Mar 2010
Posts: 919
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 2 Post(s)
Likes: 0
Liked 3 Times in 3 Posts
That's a tacoed rim. Unlace the rim. Repair the rim so that it is true to within +/- 1/16". Re-lace the rim. You're not going to be able to fix a 1/4" hop by messing around with a few spokes and expect the wheel to stay true.
furballi is offline  
Old 03-20-11, 06:07 PM
  #4  
Senior Member
Thread Starter
 
Join Date: Jun 2010
Location: Pearland, Texas
Posts: 7,579

Bikes: Cannondale, Trek, Raleigh, Santana

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 308 Post(s)
Liked 3 Times in 3 Posts
FB, This is a rim that came with a used bike, I don't know how the hop worked it's way in either, but it is a rim that looks to have considerable life left in it. The excessive tension was the primary reason I posted as I thought it could be avoided with a better plan. I'll start backing off all of the spoke's tension and see where that goes.

furball, Once the tension is released we'll find out the rim's condition.

Thanks for the help.

Brad
bradtx is offline  
Old 03-20-11, 06:25 PM
  #5  
Senior Member
 
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,545

Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter

Mentioned: 139 Post(s)
Tagged: 1 Thread(s)
Quoted: 5703 Post(s)
Liked 2,432 Times in 1,345 Posts
On most rims the strength of the rim is far less than the forces generated by the spokes, so the condition of the unspoked rim can be compensated in the build. It's the spoking that determines the final roundness.

Obviously that needs to be qualified. Rims come in a variety of weights and shapes, and for example a deep rim will be far less amenable to the spoke forces a in radial direction than a shallow one. Likewise wider rims resist the spokes more in terms of wobble. Also, long gentle distortions are less of a problem than local ones.

Back in the dark ages of light squirrely rims, most had distortion at the joint and you'd get a quick low, high,low zone (or the other way around) We considered a wheel aligned when the whole wheel was better than the joint zone.

On your wheel you have no way of knowing if hop is in the rim itself or, as I suspect, is imposed on it by the spokes. Easing the tension will help give you an idea, plus give the rim some freedom to flow. There's no need, and little to gain by taking it apart entirely.
__________________
FB
Chain-L site

An ounce of diagnosis is worth a pound of cure.

Just because I'm tired of arguing, doesn't mean you're right.

“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN

WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FBinNY is offline  
Old 03-20-11, 08:52 PM
  #6  
Senior Member
Thread Starter
 
Join Date: Jun 2010
Location: Pearland, Texas
Posts: 7,579

Bikes: Cannondale, Trek, Raleigh, Santana

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 308 Post(s)
Liked 3 Times in 3 Posts
FB, The hop is 90 d. from the joint or valve stem hole. Looks like someone has had a go at it in the past. I have to put it aside for a couple of days and I'll update the thread.

Brad
bradtx is offline  
Old 03-29-11, 06:56 AM
  #7  
Senior Member
Thread Starter
 
Join Date: Jun 2010
Location: Pearland, Texas
Posts: 7,579

Bikes: Cannondale, Trek, Raleigh, Santana

Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
Quoted: 308 Post(s)
Liked 3 Times in 3 Posts
Update

Hi All, Well, I found the problem. The rim had been damaged, looks like a head-on curb strike and was repaired, actually very well with only the slightest dip in the braking surface and a slight .2 mm decrease in circumference for about 20 mm. There are no cracks or other stress related damage.

When checking runout using the inside of the rim there was actually a very slight dip, which gave the appearance of a hop as the rim returned to normal. Very little work was required to true the wheel.

Brad
bradtx is offline  
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Chris Chicago
Bicycle Mechanics
21
10-10-16 11:57 AM
Roadie607
Bicycle Mechanics
3
09-08-14 06:25 AM
Plimogz
Bicycle Mechanics
6
07-31-11 07:01 PM
theblackbullet
Bicycle Mechanics
13
06-28-11 09:57 PM
serpico7
Bicycle Mechanics
16
06-18-11 05:24 AM

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.