Rear Fender Hanger Snapped Off - '74 Raleigh Sprite
#1
Senior Member
Thread Starter
Join Date: Jun 2009
Posts: 130
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 18 Post(s)
Likes: 0
Liked 2 Times
in
2 Posts
Rear Fender Hanger Snapped Off - '74 Raleigh Sprite
I was cleaning up a Raleigh Sprite and noticed that the unpainted metal thingy that attaches the rear fender to the frame is broken.
Can anyone suggest a decent fix that will be functional and unobtrusive? The haner is still on the fender but the top of it has snapped off somewhere along the way.
Thanks.
Can anyone suggest a decent fix that will be functional and unobtrusive? The haner is still on the fender but the top of it has snapped off somewhere along the way.
Thanks.
#2
Senior Member
Join Date: Apr 2009
Location: New Rochelle, NY
Posts: 38,713
Bikes: too many bikes from 1967 10s (5x2)Frejus to a Sumitomo Ti/Chorus aluminum 10s (10x2), plus one non-susp mtn bike I use as my commuter
Mentioned: 140 Post(s)
Tagged: 1 Thread(s)
Quoted: 5782 Post(s)
Liked 2,578 Times
in
1,429 Posts
I,m assuming you're talking about the little stirrup that wraps around the fender and folds under and has a tab that goes to the brake bolt. It used to be a readily spare part, did you try just buying one?
Otherwise, if you're good with your hands and have a pair of long nose pliers, get a stainless steel spoke and fashion a replacement. It's a simple bending job and will hold up very well.
If you want to do a more elegant job go to a hobby or hardware store and get a piece of copper or stainless steel sheet. Home depot might have something suitable with their roofing supplies. Then it's purely a matter of arts and crafts, with tin snips followed by some origami.
If you don't feel you're up to making a new stirrup, you can probably use an angle bracket, but you'll have to cut a slot in the fender so it supports from the bottom. (make sure the slot is in exactly the right place. Then a pop-rivet or nut and bolt to attach to the fender.
Otherwise, if you're good with your hands and have a pair of long nose pliers, get a stainless steel spoke and fashion a replacement. It's a simple bending job and will hold up very well.
If you want to do a more elegant job go to a hobby or hardware store and get a piece of copper or stainless steel sheet. Home depot might have something suitable with their roofing supplies. Then it's purely a matter of arts and crafts, with tin snips followed by some origami.
If you don't feel you're up to making a new stirrup, you can probably use an angle bracket, but you'll have to cut a slot in the fender so it supports from the bottom. (make sure the slot is in exactly the right place. Then a pop-rivet or nut and bolt to attach to the fender.
__________________
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
FB
Chain-L site
An ounce of diagnosis is worth a pound of cure.
Just because I'm tired of arguing, doesn't mean you're right.
“One accurate measurement is worth a thousand expert opinions” - Adm Grace Murray Hopper - USN
WARNING, I'm from New York. Thin skinned people should maintain safe distance.
Last edited by FBinNY; 06-28-11 at 09:04 PM.
#3
Senior Member
https://store.velo-orange.com/index.p...l-bracket.html
or
https://store.velo-orange.com/index.p...l-bracket.html
Their single hole version is listed as being out of stock.
or
https://store.velo-orange.com/index.p...l-bracket.html
Their single hole version is listed as being out of stock.
#4
Certified Bike Brat
Join Date: Jan 2011
Location: Montreal, Quebec
Posts: 4,251
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 5 Post(s)
Likes: 0
Liked 6 Times
in
6 Posts
Suggest you phone a couple bikeshops. The resin fenders commonly being sold come with two snap-on straddle clips and usually need only one - sometimes none. So there should be spares readily available depending on the width of your fender relative to those.
Alternatively a metal bracket intended to mount a reflector off the bender bolt already has two holes drilled to accept bolts or pop rivets and a slot to mount. Just reverse the normal orientation. Again - probably readily available at most shops.
Alternatively a metal bracket intended to mount a reflector off the bender bolt already has two holes drilled to accept bolts or pop rivets and a slot to mount. Just reverse the normal orientation. Again - probably readily available at most shops.
Thread
Thread Starter
Forum
Replies
Last Post
xnetter
Bicycle Mechanics
12
09-15-11 01:17 PM