A question concerning pedals
 

Hello everyone,

I just got a pair of used toe clip pedals and would like to ask what the triangular metal plate is used for?
And if this plate is for some kind of SPD type catch, is there a way to use it with regular shoes?

Thanks!

http://bikeforums.net/attachment.php...hmentid=310721

Nah its just clamping the plastic toe clip, length adjustment.. Cant see why you cant use regular shoes,
just the regular caveat on shoe soles being smooth enough to slide in..

The raised tab seems like it's made as some kind of a guide that must mate to some specific shoe. If it isn't doing anything, you're best bet is to file or grind it off so you have a flat surface for your shoes.

No, the raised part makes the shoe sit flat and provides clearance for the toe clip and for old-school nail on cleats that hook on the rear rail.

It's part of the pedal surface, but not part of a cleat mechanism.

I too was worried that the raised edges would interfere with normal shoes, preferably Stan Smiths which I use for cycling.

I actually got these because I wanted to try out using pedal clips and if in fact I do and can get used to using them, I'll purchase a better quality set since although these are Wellgo's, except for the axles, they're made entirely out of plastic.

Use them as they are, and if the raised lips are in the way or cut into your soles, you can file them down slightly as needed. Don't be in too much of a rush to replace these if they work. Pedal quality is mostly about durability, strength & weight. Though you can feel very poor bearing quality, anything decent will perform so close to the best that the difference won't be noticeable.

If these hold up well run them until they die, at which time you can buy better toe clip pedals, or try going clipless. IMO toe clip pedals are somewhat better suited for commuting since you use regular shoes and can walk and do errands along the way. Some also have good luck using mtn pedals and shoes, many of which have the cleat pocketed below the sole and so are also good for walking.

The raised guide hooked up with a special Shimano cleat that bolted to a Look-pattern shoe. The cleat had "wings" that slid underneath the hooks on the plate. With a cinched-down toe strap it was near impossible to get the shoe to release from the pedal.

So I thought, though not specifically which cleat it mated with. However someone "corrected" me, and I chose to let it go. I figured Telly could decide for himself if he preferred filing the tabs down.

I referred to some Shimano AX pedals- same triangular plate, but w/out the ability to hook anything under the trailing edge.

I stand corrected.

Thanks for all the info and help!
I'll try them out this weekend and if the raised lips of the metal plate are obstructing, I'll just remove the plates and add washers in their place (I always prefer to save peculiar parts because you never know when you might need them!).

? - They don't look that comfy for cycling in...

http://bikeforums.net/attachment.php...hmentid=310895
;)

Considering that I call my bike Klaus
http://images1.wikia.nocookie.net/__..._Klaus_v1F.jpg


of course I'll name the following Stan!
http://photos-chaussures.spartoo.com...6874_350_A.jpg


Just have to find something to name Roger...
https://twimg0-a.akamaihd.net/profil...rican_Dad_.jpg

You won't ever need these plates since the shoes they're made for don't exist anymore. OTOH- the single plate (without the raised lip) will make a stronger support for the screws, and for a smoother entry surface for your sole. Don't sacrifice some utility on these pedals saving parts for some future use that will never happen.

You're right of course, unfortunately I'm a bit of a hoarder and tend to stash things and then forget about them. I'll take an angle grinder to the plates or take them to a friend who can lower the lip... if needed!

There are, or were specific cleats for those old Shimano 600 pedals back in the day.

http://www.businesscycles.com/tped-shim.htm

These (the classic leather version) has always been one of my favourite casual / everyday shoes for riding with clips and straps.

I own three pairs (leather, two white and one black) and when broken-in, feel like an extension of my foot. Don't think i'll ever find anything more comfortable than these!

They have been making this shoe for well over 40 years, have been wearing them since I was a kid although for walking I now wear barefoot shoes as it is better for my back... I can't abide any kind of heel lift for any period of time.

For cycling they are great, the sole is relatively stiff and transfers power and if you are using clips and straps the design is ideal... the leather also breathes quite well.

Name your saddle Roger...

Nah... too kinky :p

http://www.trbimg.com/img-5070a128/t...lon-sm-041/600

Double corrected!!

Don't sweat it. Show me someone who's never posted an error on this forum and I'll show you a liar. (or maybe John D. Thompson)

I am usually wrong, and have learned much from most if not all of the people in the "thank you" thread. The only reason I am partially right here is that I am old and have not forgotten those pedals yet.

Thanks for the kind words.