crank set drive train info
#1
Kittery Maine / NC
Thread Starter
Join Date: Aug 2011
Posts: 175
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
crank set drive train info
All,
I am tearing my old Scott rigid frame apart and turning into a touring bike, to pull a yak I think.
The front rings are beat and so is the rear freewheel. I guess it's a freewheel since it is an early 90's mtb.
The rear is a 7 speed 11-28
the front rings are 24-34-42
Is this a good enough range for light touring up here in Maine? I will hit some climbs but not massive ones.
I am having a hard time on-line finding front rings that are not too expensive. It is not an expensive bike, so I have to go overboard on this part.
I guess changing the chain along with the rest is expected?
as always,
thanks
John
I am tearing my old Scott rigid frame apart and turning into a touring bike, to pull a yak I think.
The front rings are beat and so is the rear freewheel. I guess it's a freewheel since it is an early 90's mtb.
The rear is a 7 speed 11-28
the front rings are 24-34-42
Is this a good enough range for light touring up here in Maine? I will hit some climbs but not massive ones.
I am having a hard time on-line finding front rings that are not too expensive. It is not an expensive bike, so I have to go overboard on this part.
I guess changing the chain along with the rest is expected?
as always,
thanks
John
#2
Senior Member
Join Date: Aug 2005
Location: Pittsburgh, PA
Posts: 33,656
Bikes: '96 Litespeed Catalyst, '05 Litespeed Firenze, '06 Litespeed Tuscany, '20 Surly Midnight Special, All are 3x10. It is hilly around here!
Mentioned: 39 Post(s)
Tagged: 0 Thread(s)
Quoted: 2026 Post(s)
Likes: 0
Liked 1,095 Times
in
741 Posts
The range should be good enough unless you are towing a hugely heavy load. However, depending on your crank, you may not be even able to change the chainrings since many lower line MTB cranks have the rings riveted, not bolted, on. Even if the rings can be replaced, it might be less expensive to buy a complete replacement crank and newer MTB cranks come with a 22T granny ring.
You probably have a cassette, not a freewheel since freehubs were common by the '90's. And yes, if you change the cassette or freewheel, use a new chain.
You probably have a cassette, not a freewheel since freehubs were common by the '90's. And yes, if you change the cassette or freewheel, use a new chain.
#3
Kittery Maine / NC
Thread Starter
Join Date: Aug 2011
Posts: 175
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quoted: 0 Post(s)
Likes: 0
Liked 0 Times
in
0 Posts
Since posting I agree with you on a new crank, chain etc...
Thanks
Thanks
The range should be good enough unless you are towing a hugely heavy load. However, depending on your crank, you may not be even able to change the chainrings since many lower line MTB cranks have the rings riveted, not bolted, on. Even if the rings can be replaced, it might be less expensive to buy a complete replacement crank and newer MTB cranks come with a 22T granny ring.
You probably have a cassette, not a freewheel since freehubs were common by the '90's. And yes, if you change the cassette or freewheel, use a new chain.
You probably have a cassette, not a freewheel since freehubs were common by the '90's. And yes, if you change the cassette or freewheel, use a new chain.
Thread
Thread Starter
Forum
Replies
Last Post
sewupnut
Classic & Vintage
3
03-16-15 10:44 PM